Panasonic ET-MD77NT User manual

204
(8-1/32˝)
21432
(8-7/16˝)(1-1/4˝)
1
ET-MD77NT
Network Board for DLP™ Projector
S P E C F I L E
Specifications
Power supply: Provided from the DLP™ projector
Power consumption: Projector power consumption increases approximately 5 W
Terminals: LAN: RJ-45 x 1, 10Base-T/100Base-TX for network connection
Dimensions (W x H x D): 204 x 32 x 214 mm (8-1/32˝x 1-1/4˝x 8-7/16˝)
Weight: 280 g (10.2 lbs.)
Operating temperature: 0°C – 40°C
Operating humidity: 10% – 80% (no condensation)
Weights and dimensions shown are approximate.
Specifications subject to change without notice.
DLP and DLP logo are trademarks of Texas Instruments.
As of December 2006
This board is designed for use with the DLP™ projectors. It enables remote control of the projector and
transmission of still images to the projector from a PC on a LAN via a Web browser.
NOTE: Please use the module only on the specified Panasonic DLP™ projector.
Dimensions
unit: mm
(Dimensions given in inches are approximate.)
Note: This illustration is not drawn to scale.

2
ET-MD77DV
DVI-D Board for DLP™ Projector
S P E C F I L E
As of December 2006
Specifications
Power supply: Provided from the DLP™ projector
Power consumption: Projector power consumption increases approximately 5 W
Terminals: DVI-D input: DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP
EDID1: 480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i,
1080/25p, 1080/24p, 1080/24sF, 1080/30p
EDID2: VGA (640 x 480) – U-XGA (1,600 x 1,200),
dot clock: 25 –162 MHz
LAN: RJ-45 x 1, 10Base-T/100Base-TX for network connection
Dimensions (W x H x D): 204 x 32 x 214 mm (8-1/32˝x 1-1/4˝x 8-7/16˝)
Weight: 310 g (10.9 lbs.)
Operating temperature: 0°C – 40°C
Operating humidity: 10% – 80% (no condensation)
NOTE: Ready for single link only. Ready for the non-interlaced signals only with EDID2.
576p and 720/50p signals can be input only when this unit is used with the PT-DW10000,
PT-D10000, PT-DW7000 or PT-D7700.
Weights and dimensions shown are approximate.
Specifications subject to change without notice.
DLP and DLP logo are trademarks of Texas Instruments.
This input board is designed for use with the DLP™ projectors. It enables the input of a digital signal (DVI-D) from
a computer. Remote control of the projector is also possible from an external computer connected via LAN.
NOTE: Please use the module only on the specified Panasonic DLP™ projector.
Dimensions DVI-D output connector pin
assignment
unit: mm
(Dimensions given in inches are approximate.)
204
(8-1/32˝)
21432
(8-7/16˝)(1-1/4˝)
Note: This illustration is not drawn to scale.
no. signal
1 T, M, D, S data 2-
2 T, M, D, S data 2+
3 T, M, D, S data 2/4 shield
4 T, M, D, S data 4-
5 T, M, D, S data 4+
6 DDC clock
7 DDC clock
8NC
9 T, M, D, S data 1-
10 T, M, D, S data 1+
11 T, M, D, S data 1/3 shield
12 T, M, D, S data 3-
13 T, M, D, S data 3+
14 +5 V
15 GND
16 Hot plug detection
17 T, M, D, S data 0-
18 T, M, D, S data 0+
19 T, M, D, S data 0/5 shield
20 T, M, D, S data 5-
21 T, M, D, S data 5+
22 T, M, D, S clock shield
23 T, M, D, S clock +
24 T, M, D, S clock -

3
ET-MD77SD1
SD-SDI Board for DLP™ Projector
S P E C F I L E
As of December 2006
204
(8-1/32˝)
21432
(8-7/16˝)(1-1/4˝)
Specifications
Power supply: Provided from the DLP™ projector
Power consumption: Projector power consumption increases approximately 5 W
Terminals: Serial input: BNC x 1, 4:2:2 digital serial component signal, SMPTE 259M compliant,
480i, 576i
Serial output: BNC x 1, active through
LAN: RJ-45 x 1, 10Base-T/100Base-TX for network connection
Dimensions (W x H x D): 204 x 32 x 214 mm (8-1/32˝x 1-1/4˝x 8-7/16˝)
Weight: 290 g (10.2 lbs.)
Operating temperature: 0°C – 40°C
Operating humidity: 10% – 80% (no condensation)
Weights and dimensions shown are approximate.
Specifications subject to change without notice.
DLP and DLP logo are trademarks of Texas Instruments.
This board is designed for use with the DLP™ projectors. It enables the input of a 4:2:2 digital serial component
signal (SMPTE259M-compliant). Remote control of the projector is also possible from an external computer
connected via LAN. NOTE: Please use the module only on the specified Panasonic DLP™ projector.
Dimensions
unit: mm
(Dimensions given in inches are approximate.)
Note: This illustration is not drawn to scale.

4
ET-MD77SD3
HD-SDI/SD-SDI Board for DLP™ Projector
S P E C F I L E
As of December 2006
204
(8-1/32˝)
21432
(8-7/16˝)(1-1/4˝)
Specifications
Power supply: Provided from the DLP™ projector
Power consumption: Projector power consumption increases approximately 10 W
Terminals: Serial input: BNC x 1
4:2:2 digital serial component signal: SMPTE 259M compliant,
480i, 576i
HD digital serial component signal: SMPTE 292M compiant,
720/60p, 720/50p, 1035/60i, 1080/60i, 1080/50i,
1080/25p, 1080/24p, 1080/24sF, 1080/30p
Serial output: BNC x 1, active through
LAN: RJ-45 x 1, 10Base-T/100Base-TX for network connection
Dimensions (W x H x D): 204 x 32 x 214 mm (8-1/32˝x 1-1/4˝x 8-7/16˝)
Weight: 290 g (10.2 lbs.)
Operating temperature: 0°C – 40°C
Operating humidity: 10% – 80% (no condensation)
NOTE: Use connection cables of 5CFB or higher (ex. 5CFB, 7CFB, 5CFTX, etc.).
720/50p signals can be input only when this unit is used with the PT-DW10000, PT-D10000,
PT-DW7000 or PT-D7700.
Weights and dimensions shown are approximate.
Specifications subject to change without notice.
DLP and DLP logo are trademarks of Texas Instruments.
This board is designed for use with the DLP™ projectors. It enables the input of a HD digital serial component
signal (SMPTE292M-compliant). Remote control of the projector is also possible from an external computer
connected via LAN.
NOTE: Please use the module only on the specified Panasonic DLP™ projector.
Dimensions
unit: mm
(Dimensions given in inches are approximate.)
Note: This illustration is not drawn to scale.

204
(8-1/32˝)
214
(8-7/16˝)
32
(1-1/4˝)
SPEC FILE
ET-MD100SD4
HD-SDI Input Board for the PT-DW10000
As of February 2008 < 1 >
Specifications
Power supply: Provided from the DLP™ projector
Power consumption: Projector power consumption increases approximately 10 W
Terminals: Link A/Link B input: BNC x 1 for each
SD-SDI signal (YCBCR4:2:2 10 bit)
SMPTE 259M compliant: 480i, 576i
Single link HD-SDI signal (YCBCR4:2:2 10 bit)
SMPTE 292M compiant: 1720/50p, 720/60p, 1080/50i, 1080/60i, 1080/25p,
1080/24p, 1080/24sF, 1080/30p
Dual link HD-SDI signal (RGB 4:4:4 12 bit/10 bit)
SMPTE 372M compiant: 1920 x 1080/50i, 1920 x 1080/60i, 1920 x 1080/25p,
1920 x 1080/24p, 1920 x 1080/24sF, 1920 x 1080/30p
Dual link HD-SDI signal (X´Y´Z´ 4:4:4 12 bit)
2048 x 1080/24p, 2048 x 1080/24sF
Dimensions (W x H x D): 204 x 32 x 214 mm (8-1/32˝ x 1-1/4˝ x 8-7/16˝)
Weight: 250 g (8.8 oz)
Operating temperature: 0°C – 45°C (32°F– 113°F)
Operating humidity: 10% – 80% (no condensation)
Weights and dimensions shown are approximate. Specifications subject to change without notice.
DLP and the DLP logo are trademarks of Texas Instruments. All other trademarks are the property of their respective trademark owners.
NOTE: Please use the module only on the Panasonic DLP™ projector PT-DW10000.
NOTE: Use connection cables of 5CFB or higher (ex. 5CFB, 7CFB, 5CFTX, etc.).
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
Dimensions
This board is designed for use with the DLP™ projector PT-DW10000. It enables the input of a HD-SDI (SMPTE
292M) and dual link HD-SDI (SMPTE 372M). Remote control of the projector is also possible from an external com-
puter connected via LAN.