Panasonic ET-PKD130B User manual

ENGLISH
ENGLISH
FRANÇAIS
DEUTSCH
Thank you for purchasing this Panasonic product.
■To customers
The “Installation Instructions” is intended for use by installation personnel. Be sure to employ certified personnel to
perform the installation.
After installation, have the installation personnel return these “Installation Instructions” to you, and save it for future use.
When moving or removing the projector, give this manual to the certified personnel and have them perform the procedure.
■To installation personnel
Read the “Installation Instructions” thoroughly and then perform the operation correctly and safely.
Be sure to read through the section entitled “Read this first!” (page 3) before proceeding with the installation.
If the separately sold ET-DLE030 Fixed-focus lens will be used with the projector, obtain the “Operating Instructions”for
the lens from the customer and refer to this manual and the “Installation Instructions” during installation.
After installation, return these “Installation Instructions” to the customer.
* The figure above shows this product combined with the separately sold ET-PKD130H Ceiling Mount Bracket (for High
Ceilings, 6-axis Adjustment).
Installation Instructions
Projector Mount Bracket
Model No. ET-PKD130B
TQZJ577-7
ET-PKD130B_EN_TQZJ577-7.indd 1 2017/03/13 19:04:50

2 - ENGLISH
Contents
Read this rst! ................................................................................................... 3
Product components......................................................................................... 4
Standard installation dimensions.................................................................... 5
When using the ET-DLE030 Fixed-focus lens.................................................................... 5
When using a lens other than the ET-DLE030 Fixed-focus lens or a PT-RZ575 /
PT-RZ570 projector ............................................................................................................ 8
Installation........................................................................................................ 12
Setting up the screen........................................................................................................ 12
Screws tightening torques ................................................................................................ 12
Installing the bracket to the projector................................................................................ 12
Attaching the drop prevention kit to the projector ............................................................. 14
Using an existing bracket............................................................................... 15
Removing the projector from the existing bracket ............................................................ 15
Mounting the projector on an existing bracket.................................................................. 16
Specications .................................................................................................. 18
ET-PKD130B_EN_TQZJ577-7.indd 2 2017/03/13 19:04:50

ENGLISH - 3
Read this rst!
WARNING:
Installation work should only be carried out by the certied personnel.
zIf this product is not installed correctly, serious accidents may result.
zFollow the instructions specied in “Installation” of this manual, and perform secure installation.
Install the ceiling mount bracket in accordance with the structure and materials of the installation
location.
zIf a mistake is made in the installation procedure, the ceiling mount bracket may fall down and an injury may
result.
Mounting must be carried out by two or more persons.
zWhen installing the projector in an overhead location, for example, in a high ceiling, at least two persons will
be required to handle the installation.
Make sure that your footing is safe and secure during installation.
zIf your footing is not secure, you may trip or fall down, and an injury may result.
Do not loosen or remove the unit screws and bolts unnecessarily.
zThe projector may fall down and an injury may result.
Do not install in a location that is not strong enough.
zIf the installation location is not strong enough, the unit may fall down and damage to the projector or an
injury may result.
Do not install the ceiling mount bracket in humid or dusty locations or in locations where the ceiling
mount bracket may be exposed to oily smoke, steam, or excessive heat.
zFailure to obey may result in re or electric shock. In addition, oil will cause the plastic to deteriorate, which
may result in a drop hazard.
Do not allow children to reach the supplied screws and metal ttings.
zThese items can cause personal injury if swallowed.
zIf swallowed, seek medical help immediately.
Do not disassemble or modify the projector mount bracket.
zThe projector may be damaged or fall down, and an injury may result.
CAUTION:
Install only the designated projector.
Install only using the designated method.
zFailure to obey may result in dropping, damage to the projector, or injury.
Do not install the ceiling mount bracket in a place which may impede projector ventilation.
zIf this is not observed, re may result.
Do not hang from or hang objects on the projector or ceiling mount bracket.
zThe projector may fall and cause injury.
Use only the specied ceiling mount bracket (for high ceilings or for low ceilings).
zFailure to obey may result in dropping, damage to the projector, or injury.
Always use the supplied parts when performing installation.
zOtherwise, this may cause damaged projector to fall and cause injury.
Install the mounting screws and power cable in such a way that they will not make contact with the
inside metals of the ceiling.
zElectric shocks may result from contact with any metal objects inside the ceiling.
■Panasonic disclaims all liability for any accidents or any damage caused by the installation of the
ceiling mount bracket using methods that are not described in these Installation Instructions or
methods that do not use the parts specied in these Instructions.
■ If products are no longer being used, they should be dismantled and removed by the certied
personnel as soon as possible.
Always follow these precautions
ET-PKD130B_EN_TQZJ577-7.indd 3 2017/03/13 19:04:50

4 - ENGLISH
Product components
This is a projector mount bracket for installing projectors.
Use this together with the ceiling mount bracket for high ceilings or low ceilings (sold separately).
■Supported ceiling mount brackets and projectors
zCeiling Mount Bracket
ET-PKD130H / ET-PKD120H / ET-PKD120S / ET-PKD310H / ET-PKD310S / ET-PKD56H / ET-PKD55S /
ET-PKD100H / ET-PKD100S / ET-PKD77H / ET-PKD75S
zProjector
PT-RZ575 / PT-RZ770 / PT-RW730 / PT-RZ660 / PT-RW620 / PT-RZ970 / PT-RW930 / PT-RX110 / PT-DZ780 /
PT-RZ570 / PT-DW750 / PT-DX820 / PT-RZ670 / PT-RW630 / PT-DZ870 / PT-DW830 / PT-DX100 / PT-DZ770 /
PT-DZ680 / PT-DZ6710 / PT-DZ6700 / PT-DW740 / PT-DW730 / PT-DW640 / PT-DW6300 / PT-DX810 /
PT-DX800 / PT-DX610 / PT-D6000 / PT-D5000
Note
zInstallation of the ET-PKD130H ceiling mount bracket (for high ceilings, 6-axis adjustment) is recommended if
the projector will be used with the optional ET-DLE030 Fixed-focus lens. When installed using the
ET-PKD130H you can more accurately adjust horizontal tilt of the projector.
zProducts not listed above may be supported in some cases. For details, refer to the operating instructions of
your ceiling mount bracket (for high ceilings or for low ceilings) and projector.
zIn this document, the letters at the end of the projector part numbers are omitted.
■Structural components
Check that the package contains the following parts. The number enclosed in < > is the quantity.
Projector mount bracket < 1 >
This is used to install the projector itself.
The bracket has a function for adjusting horizontal tilt.
Hex head bolt,
captive washer < 6 >
(M6×16) These are used to mount the bracket onto the projector.
Flat washer < 2 >
(M8)
Prevents the projector from falling.
Wire rope < 1 >
(Approx. 2.5 mm (3/32")
wire diameter,
800 mm (31-1/2") length)
zTightening torque for the screws are M6: 4±0.5 N•m, M8: 10±1 N•m.
zWhen tightening up the screws, use a tool such as a torque screwdriver or torque wrench. Do not use electric
screwdrivers or impact screwdrivers.
Note
zThe projector models listed below require ve of the six supplied captive washer hex head bolts (M6 × 16) for
installation.
Model: PT-RZ575 / PT-RZ770 / PT-RW730 / PT-RZ660 / PT-RW620 / PT-RZ970 / PT-RW930 / PT-RX110 /
PT-DZ780 / PT-RZ570 / PT-DW750 / PT-DX820 / PT-RZ670 / PT-RW630 / PT-DZ770 / PT-DZ680 /
PT-DZ6710 / PT-DZ6700 / PT-DW740 / PT-DW730 / PT-DW640 / PT-DW6300 / PT-DX810 / PT-DX800 /
PT-DX610 / PT-D6000 / PT-D5000
ET-PKD130B_EN_TQZJ577-7.indd 4 2017/03/13 19:04:51

ENGLISH - 5
Product components (continued)
Attention
zDispose of the packaging materials properly after taking the product out of it.
zStore small parts in an appropriate manner, and keep them away from small children.
Standard installation dimensions
<When using the ET-DLE030 Fixed-focus lens>
The dimensional relationship between the screen and the projector is shown below.
Establish the dimensions after assessing the area possible for installation.
zUse of the ET-PKD130H ceiling mount bracket is recommended.
■Dimensional reationship diagram
zAlso refer to the "Operating Instructions" for the ET-DLE030 Fixed-focus lens.
zWhen using the ET-PKD130H, the L1, L2, L3, L4 and L5 values assume that the projector is positioned at the
center longitudinal slide position. For details on how to do this, refer to "Before Installation" in the ET-PKD130H
Installation Instructions.
SH
SW
SD
SH A1SW
(Units : mm ("))
Screen
Screen
100
(3-15/16")
100
(3-15/16")
200
(7-7/8")
200
(7-7/8")
L3
L5
L4
L1
L2
350 -510*
(13-3/4" -20-1/16")
Ceiling
* Includes the thickness of
the attachment plate.
H1
Projected image
ET-PKD130B_EN_TQZJ577-7.indd 5 2017/03/13 19:04:51

6 - ENGLISH
Standard installation dimensions (continued)
Note
zThis illustration assumes that the projector will be installed so that the projected image lls the screen and is
properly aligned with it.
zThis drawing is not in exact scale.
SH Image height L4 From screen to rear of projector
SW Image width L5 From center of attachment plate to front of projector
SD Projected image size A1 From top edge of screen to top of projector
L1 Projection distance (from screen to mirror reective
surface*) H1 From bottom of set (the surface in contact with this
product) to top of projector
L2 From screen to tip of lens
L3 From screen to front of projector
* The mirror reective surface is inside the xed-focus lens, and is not visible from the outside.
Attention
zInstall the projector with at least 500 mm (19-11/16") gap from the surrounding walls or objects in order to
ensure that the air intake/exhaust ports of the projector will not be blocked.
zAvoid setting up in places which are subject to sudden temperature changes, such as near an air conditioner
or lighting equipment (studio lamps, etc.).
zRegardless of the projector model, set up the projector so that the projected image is rectangular and the
back of the projector and the screen are parallel. Depending on your projector, however, keystone distortion
correction via the [GEOMETRY (2D)] or [GEOMETRY] function may be possible, even after setup.
Refer to the Operating Instructions of ET-DLE030 for details.
Note
zDimension L4 is not the distance from the projector rear panel to the wall, but the distance from the projector
rear panel to the screen.
zWhen [GEOMETRY (2D)], [GEOMETRY] and [KEYSTONE] are used, distance is corrected to become smaller
than the specied image size.
zThe illustrations of projectors in this manual are for informational purposes only and do not represent a specic
model. Congurations may vary with the model.
■ Dimensional relationship
zH1 and L5 values (Unit: m)
PT-RZ770 / RW730 / RZ660 / RW620 / RZ970 /
RW930 / RX110 / RZ670 / RW630 / DZ870 /
DW830 / DX100
PT-DZ770 / DZ680 / DZ6710 / DZ6700 / DW740
/ DW730 / DW640 / DW6300 / DX810 / DX800 /
DX610 / D6000 / D5000
PT-DZ780 /
DW750 / DX820
H1 0.196 0.155 0.175
L5 0.239 0.147 0.167
zL1, A1 calculation formula (Unit: m)
Check the projected image size SD (m) and use each formula to determine projection distance (L1) and top of set
to top edge of screen (A1).
By determining L1 and A1, you can calculate all other dimensions.
(Values obtained by the calculation formulas contain a slight error.)
When calculating a projection distance using image size designation (value in inches), multiply the value in inches
by 0.0254 and substitute it into SD in the formula for calculating the projection distance.
In the case of PT-RZ770 / PT-RZ660 / PT-RZ970 / PT-RZ670 / PT-DZ870
For 16:10 aspect ratio For 16:9 aspect ratio For 4:3 aspect ratio
L1 = 0.3205 × SD + 0.0047 = 0.3294 × SD + 0.0047 = 0.3628 × SD + 0.0047
A1 = 0.1977 × SD
- 0.0721 = 0.2304 × SD - 0.0721 = 0.2238 × SD - 0.0721
In the case of PT-RW730 / PT-RW620 / PT-RW930 / PT-RW630 / PT-DW830
For 16:10 aspect ratio For 16:9 aspect ratio For 4:3 aspect ratio
L1 = 0.3365 × SD + 0.0047 = 0.3459 × SD + 0.0047 = 0.3809 × SD + 0.0047
A1 = 0.2597 × SD
- 0.0740 = 0.2942 × SD - 0.0740 = 0.2941 × SD - 0.0740
ET-PKD130B_EN_TQZJ577-7.indd 6 2017/03/13 19:04:52

ENGLISH - 7
Standard installation dimensions (continued)
In the case of PT-RX110 / PT-DX100
For 4:3 aspect ratio For 16:9 aspect ratio
L1 = 0.3133 × SD + 0.0047 = 0.3413 × SD + 0.0047
A1 = 0.1881 × SD
- 0.0715 = 0.2866 × SD - 0.0715
In the case of PT-DZ780 / DZ770 / DZ680 / DZ6710 / DZ6700
For 16:10 aspect ratio For 16:9 aspect ratio For 4:3 aspect ratio
L1 = 0.3205 × SD + 0.0047 = 0.3294 × SD + 0.0047 = 0.3628 × SD + 0.0047
A1 = 0.1977 × SD
- 0.0671 = 0.2304 × SD - 0.0671 = 0.2238 × SD - 0.0671
In the case of PT-DW750 / DW740 / DW730 / DW640 / DW6300
For 16:10 aspect ratio For 16:9 aspect ratio For 4:3 aspect ratio
L1 = 0.3365 × SD + 0.0047 = 0.3459 × SD + 0.0047 = 0.3809 × SD + 0.0047
A1 = 0.2597 × SD
- 0.0690 = 0.2942 × SD - 0.0690 = 0.2941 × SD - 0.0690
In the case of PT-DX820 / DX810 / DX800 / DX610 / D6000 / D5000
For 4:3 aspect ratio For 16:9 aspect ratio
L1 = 0.3133 × SD + 0.0047 = 0.3413 × SD + 0.0047
A1 = 0.1881 × SD
- 0.0665 = 0.2866 × SD - 0.0665
zL2, L3 and L4 calculation formulas (Unit: m)
PT-RZ770 / RW730 / RZ660 /
RW620 / RZ970 / RW930 /
RX110 / RZ670 / RW630
PT-DZ870 /
DW830 / DX100
PT-DZ770 / DW740 / DX810 / DZ680 / DW640 /
DX610 / DW730 / DX800 / DZ6710 / DZ6700 /
DW6300 / D6000 / D5000
PT-DZ780 /
DW750 / DX820
L2 L1 + 0.023
L3 L1 - 0.166 L1 - 0.146
L4 L1 - 0.704 L1 - 0.679 L1 - 0.589 L1 - 0.644
ET-PKD130B_EN_TQZJ577-7.indd 7 2017/03/13 19:04:52

8 - ENGLISH
Standard installation dimensions (continued)
<When using a lens other than the ET-DLE030 Fixed-focus lens or a
PT-RZ575 / PT-RZ570 projector>
The dimensional relationship between the screen and the projector is shown below.
Establish the dimensions after assessing the area possible for installation.
The zoom function of the lens allows you to adjust the projection distance (excluding the ET-DLE055). Fine adjust
while checking the projected image.
■Dimensional relationship diagram
zThe illustration shows the ET-PKD120H ceiling mount bracket mounted on a projector.
SH SH
L (LW/LT)
Screen
H1
L5
SW
SW
SD
100
(3-15/16")
100
(3-15/16")
200
(7-7/8")
200
(7-7/8")
L1
Projected image
Ceiling
(Units : mm ("))
Note
zThis illustration assumes that the projector will be installed so that the projected image lls the screen and is
properly aligned with it.
zThis drawing is not in exact scale.
SH Image height L1 Lens protrusion dimension (from front of set to tip of lens)
SW Image width L5 From front center of the attachment plate to front of projector
SD Projected image size H1 From lens center to attachment plate (includes the thickness of the
attachment plate)
L Projection distance
Attention
zInstall the projector with at least 500 mm (19-11/16") gap from the surrounding walls or objects in order to
ensure that the air intake/exhaust ports of the projector will not be blocked.
zAvoid setting up in places which are subject to sudden temperature changes, such as near an air conditioner
or lighting equipment (studio lamps, etc.).
ET-PKD130B_EN_TQZJ577-7.indd 8 2017/03/13 19:04:52

ENGLISH - 9
Standard installation dimensions (continued)
Note
zThe illustrations of projectors in this manual are for
informational purposes only and do not represent
a specic model. Congurations may vary with the
model.
zWhen using the existing ET-PKD100H and ET-
PKD77H ceiling mount brackets for high ceilings, the
center position of the projection lens of the currently
installed projector shifts by 54 mm (2-1/8″) based on
the central axis of the adjustment pole. However,
when replaced with PT-DZ870, for example, the
center position will shift to the left by 54 mm (2-1/8″)
as shown in the gure on the right.
zWhen using the existing ET-PKD100S and ET-
PKD75S ceiling mount brackets for low ceilings, the
center position of the projection lens of the currently
installed projector is aligned with the horizontal
center of the attachment plate. However, when replaced with PT-DZ870, for example, the center position will
shift to the left by 54 mm (2-1/8″) as shown in the gure on the right.
■ Dimensional relationship
zH1 and L5 values (Unit: m)
PT-RZ770 / RW730 / RZ660
/ RW620 / RZ970 / RW930 /
RX110 / RZ670 / RW630 /
DZ870 / DW830 / DX100
PT-DZ770 / DZ680 / DZ6710 /
DZ6700 / DW740 / DW730 / DW640
/ DW6300 / DX810 / DX800 / DX610
/ D6000 / D5000
PT-DZ780 /
DW750 /
DX820
PT-RZ575 /
RZ570
ET-PKD120H H1 0.464 - 0.544 0.428 - 0.508 0.443 - 0.523 0.442 - 0.522
L5 0.244 0.152 0.172 0.175
ET-PKD310H / PKD56H /
PKD77H
H1 0.452 - 0.532 0.416 - 0.496 0.431 - 0.511 0.430 - 0.510
L5 0.244 0.152 0.172 0.175
ET-PKD100H H1 0.526 - 0.646 0.491 - 0.611 0.506 - 0.626 0.505 - 0.625
L5 0.244 0.152 0.172 0.175
ET-PKD120S / PKD310S /
PKD55S / PKD100S / PKD75S
H1 0.221 0.185 0.200 0.199
L5 0.239 0.147 0.167 0.170
zL1 values (Unit: m)
PT-RZ770 / RW730 / RZ660 / RW620 /
RZ970 / RW930 / RX110 / RZ670 / RW630 /
DZ870 / DW830 / DX100 / DZ770 / DW740 /
DX810 / DW730 / DX800
PT-DZ680 / DW640 / DX610 / DZ6710
/ DZ6700/ DW6300 / D6000 / D5000
PT-DZ780 /
DW750 / DX820
Standard zoom lens 0.043 0.017 0.023
ET-DLE055 0.027 0.007
ET-DLE080 / DLE085 0.084 0.064
ET-DLE150 0.044 0.024
ET-DLE250 0.045 0.025
ET-DLE350 0.051 0.031
ET-DLE450 0.095 0.075
PT-RZ570 PT-RZ575
0.032 0.021
zFormulas for calculating projection distance by projection lens
Check the projected image size SD (m) and use the following formula to determine projection distance.
(Values obtained by the calculation formulas in the tables below contain a slight error.)
When calculating a projection distance using image size designation (value in inches), multiply the value in inches
by 0.0254 and substitute it into SD in the formula for calculating the projection distance.
FILTER
CLEANING
OPEN
CLOSE
FILTER
CLEANING
OPEN
CLOSE
FILTER
CLEANING
OPEN
CLOSE
FILTER
CLEANING
OPEN
CLOSE
54 mm (2-1/8″)
ET-PKD130B
ET-PKD130B
<Example>
When using
ET-PKD100H
<Example>
When using
ET-PKD100S
54 mm (2-1/8″)
ET-PKD130B_EN_TQZJ577-7.indd 9 2017/03/13 19:04:54

10 - ENGLISH
In the case of PT-RZ770 / RZ660 / RZ970 / DZ780 / RZ670 / DZ870 / DZ770 / DZ680 / DZ6710 / DZ6700 (Unit: m)
Projection Lens Aspect ratio Projection distance (L) formula
Minimum (LW) Maximum (LT)
Standard zoom lens
(supplied with the PT-RZ770 /
RZ660 / RZ970 / DZ780 /
RZ670 / DZ870 / DZ770)
16 : 10 = 1.4906 × SD
- 0.0746 = 2.0814 × SD - 0.0725
16 : 9 = 1.5320 × SD
- 0.0746 = 2.1393 × SD - 0.0725
4 : 3 = 1.6874 × SD
- 0.0746 = 2.3563 × SD - 0.0725
Standard zoom lens
(supplied with the
PT-DZ680 / DZ6710 / DZ6700)
16 : 10 = 1.5551 × SD
- 0.0745 = 2.0787 × SD - 0.0734
16 : 9 = 1.5984 × SD
- 0.0745 = 2.1378 × SD - 0.0734
4 : 3 = 1.7598 × SD
- 0.0745 = 2.3583 × SD - 0.0734
Fixed-focus lens
(ET-DLE055)
16 : 10 = 0.6893 × SD
- 0.0476
16 : 9 = 0.7084 × SD
- 0.0476
4 : 3 = 0.7803 × SD
- 0.0476
Ultra short focus zoom lens
(ET-DLE085,
ET-DLE080)
16 : 10 = 0.6865 × SD
- 0.0471 = 0.8498 × SD - 0.0442
16 : 9 = 0.7056 × SD
- 0.0471 = 0.8735 × SD - 0.0442
4 : 3 = 0.7772 × SD
- 0.0471 = 0.9621 × SD - 0.0442
Short focus zoom lens
(ET-DLE150)
16 : 10 = 1.1259 × SD
- 0.0540 = 1.6243 × SD - 0.0498
16 : 9 = 1.1572 × SD
- 0.0540 = 1.6695 × SD - 0.0498
4 : 3 = 1.2747 × SD
- 0.0540 = 1.8388 × SD - 0.0498
Intermediate focus zoom lens
(ET-DLE250)
16 : 10 = 1.9665 × SD
- 0.0800 = 3.1059 × SD - 0.0792
16 : 9 = 2.0212 × SD
- 0.0800 = 3.1923 × SD - 0.0792
4 : 3 = 2.2263 × SD
- 0.0800 = 3.5161 × SD - 0.0792
Long focus zoom lens
(ET-DLE350)
16 : 10 = 3.1000 × SD
- 0.1351 = 4.6843 × SD - 0.1346
16 : 9 = 3.1862 × SD
- 0.1351 = 4.8146 × SD - 0.1346
4 : 3 = 3.5094 × SD
- 0.1351 = 5.3030 × SD - 0.1346
Ultra long focus zoom lens
(ET-DLE450)
16 : 10 = 4.6931 × SD
- 0.3017 = 7.4193 × SD - 0.2991
16 : 9 = 4.8236 × SD
- 0.3017 = 7.6256 × SD - 0.2991
4 : 3 = 5.3129 × SD
- 0.3017 = 8.3992 × SD - 0.2991
Note
zUse the ET-DLE085 ultra short focus zoom lens for the PT-RZ770, PT-RZ660, PT-RZ970, PT-DZ780,
PT-RZ670 and PT-DZ870 projectors.
zWhen [GEOMETRY (2D)], [KEYSTONE (3D)], [GEOMETRY] and [KEYSTONE] are used, distance is corrected
to become smaller than the specied image size.
In the case of PT-RW730 / RW620 / RW930 / DW750 / RW630 / DW830 / DW740 / DW730 / DW640 / DW6300 (Unit: m)
Projection Lens Aspect ratio Projection distance (L) formula
Minimum (LW) Maximum (LT)
Standard zoom lens
(supplied with the PT-RW730 /
RW620 / RW930 / DW750 / RW630 /
DW830 / DW740 / DW730)
16 : 10 = 1.5651 × SD
- 0.0746 = 2.1855 × SD - 0.0725
16 : 9 = 1.6086 × SD
- 0.0746 = 2.2462 × SD - 0.0725
4 : 3 = 1.7715 × SD
- 0.0746 = 2.4736 × SD - 0.0725
Standard zoom lens
(supplied with the
PT-DW640 / DW6300)
16 : 10 = 1.5630 × SD
- 0.0650 = 2.0630 × SD - 0.0638
16 : 9 = 1.6063 × SD
- 0.0650 = 2.1220 × SD - 0.0638
4 : 3 = 1.7717 × SD
- 0.0650 = 2.3346 × SD - 0.0638
Fixed-focus lens
(ET-DLE055)
16 : 10 = 0.7237 × SD
- 0.0476
16 : 9 = 0.7438 × SD
- 0.0476
4 : 3 = 0.8191 × SD
- 0.0476
Ultra short focus zoom lens
(ET-DLE085,
ET-DLE080)
16 : 10 = 0.7209 × SD
- 0.0471 = 0.8923 × SD - 0.0442
16 : 9 = 0.7409 × SD
- 0.0471 = 0.9171 × SD - 0.0442
4 : 3 = 0.8159 × SD
- 0.0471 = 1.0100 × SD - 0.0442
Short focus zoom lens
(ET-DLE150)
16 : 10 = 1.1822 × SD
- 0.0540 = 1.7055 × SD - 0.0498
16 : 9 = 1.2151 × SD
- 0.0540 = 1.7529 × SD - 0.0498
4 : 3 = 1.3381 × SD
- 0.0540 = 1.9304 × SD - 0.0498
Standard installation dimensions (continued)
ET-PKD130B_EN_TQZJ577-7.indd 10 2017/03/13 19:04:54

ENGLISH - 11
Projection Lens Aspect ratio Projection distance (L) formula
Minimum (LW) Maximum (LT)
Intermediate focus zoom lens
(ET-DLE250)
16 : 10 = 2.0649 × SD
- 0.0800 = 3.2612 × SD - 0.0792
16 : 9 = 2.1223 × SD
- 0.0800 = 3.3519 × SD - 0.0792
4 : 3 = 2.3371 × SD
- 0.0800 = 3.6912 × SD - 0.0792
Long focus zoom lens
(ET-DLE350)
16 : 10 = 3.2550 × SD
- 0.1351 = 4.9185 × SD - 0.1346
16 : 9 = 3.3455 × SD
- 0.1351 = 5.0553 × SD - 0.1346
4 : 3 = 3.6842 × SD
- 0.1351 = 5.5671 × SD - 0.1346
Ultra long focus zoom lens
(ET-DLE450)
16 : 10 = 4.9277 × SD
- 0.3017 = 7.7903 × SD - 0.2991
16 : 9 = 5.0647 × SD
- 0.3017 = 8.0069 × SD - 0.2991
4 : 3 = 5.5775 × SD
- 0.3017 = 8.8174 × SD - 0.2991
Note
z
Use the ET-DLE085 ultra short focus zoom lens for the PT-RW730, PT-RW620, PT-RW930, PT-DW750, PT-RW630
and PT-DW830 projectors.
zWhen [KEYSTONE] is used, distance is corrected to become smaller than the specied screen size.
In the case of PT-RX110 / DX820 / DX100 / DX810 / DX800 / DX610 / D6000 / D5000 (Unit: m)
Projection Lens Aspect ratio Projection distance (L) formula
Minimum (LW) Maximum (LT)
Standard zoom lens
(supplied with the
PT-RX110 / DX820 / DX100 /
DX810 / DX800)
4 : 3 = 1.4571 × SD
- 0.0746 = 2.0346 × SD - 0.0725
16 : 9 = 1.5875 × SD
- 0.0746 = 2.2167 × SD - 0.0725
Standard zoom lens
(supplied with the
PT-DX610 / D6000 / D5000)
4 : 3 = 1.4567 × SD
- 0.0650 = 1.9213 × SD - 0.0638
16 : 9 = 1.5866 × SD
- 0.0650 = 2.0945 × SD - 0.0638
Fixed-focus lens
(ET-DLE055)
4 : 3 = 0.6738 × SD
- 0.0476
16 : 9 = 0.7340 × SD
- 0.0476
Ultra short focus zoom lens
(ET-DLE085,
ET-DLE080)
4 : 3 = 0.6711 × SD
- 0.0471 = 0.8307 × SD - 0.0442
16 : 9 = 0.7311 × SD
- 0.0471 = 0.9051 × SD - 0.0442
Short focus zoom lens
(ET-DLE150)
4 : 3 = 1.1006 × SD
- 0.0540 = 1.5878 × SD - 0.0498
16 : 9 = 1.1991 × SD
- 0.0540 = 1.7299 × SD - 0.0498
Intermediate focus zoom lens
(ET-DLE250)
4 : 3 = 1.9224 × SD
- 0.0800 = 3.0361 × SD - 0.0792
16 : 9 = 2.0943 × SD
- 0.0800 = 3.3078 × SD - 0.0792
Long focus zoom lens
(ET-DLE350)
4 : 3 = 3.0304 × SD
- 0.1351 = 4.5791 × SD - 0.1346
16 : 9 = 3.3015 × SD
- 0.1351 = 4.9888 × SD - 0.1346
Ultra long focus zoom lens
(ET-DLE450)
4 : 3 = 4.5876 × SD
- 0.3017 = 7.2526 × SD - 0.2991
16 : 9 = 4.9981 × SD
- 0.3017 = 7.9015 × SD - 0.2991
Note
zUse the ET-DLE085 ultra short focus zoom lens for the PT-RX110, PT-DX820 and PT-DX100 projectors.
zWhen [KEYSTONE] is used, distance is corrected to become smaller than the specied screen size.
In the case of PT-RZ570 (Unit: m)
Aspect ratio Projection distance (L) formula
Minimum (LW) Maximum (LT)
16:10 = 1.2598 × SD
- 0.0526 = 2.5118 × SD - 0.0390
16:9 = 1.2949 × SD
- 0.0526 = 2.5816 × SD - 0.0390
4:3 = 1.4262 × SD
- 0.0526 = 2.8436 × SD - 0.0390
In the case of PT-RZ575 (Unit: m)
Aspect ratio Projection distance (L) formula
16:10 = 0.6893 × SD - 0.0476
16:9 = 0.7084 × SD - 0.0476
4:3 = 0.7803 × SD - 0.0476
Standard installation dimensions (continued)
ET-PKD130B_EN_TQZJ577-7.indd 11 2017/03/13 19:04:54

12 - ENGLISH
After checking the height, width, and structure of the installation location while referring to “Standard installation
dimensions” on pages 5 to 11, determine the appropriate positions for setting up the screen and installing the
projector.
To mount this product on an already installed ceiling mount bracket, refer to "Using an existing bracket" on pages
15 to 17.
Setting up the screen
Set up the screen according to the specied method in a position which takes into account the projection distance
and angle and the type of screen being used.
Screws tightening torques
M6............... 4±0.5 N•m
M8............... 10±1 N•m
M10............. 20±1 N•m
zUse a torque screwdriver or torque wrench to tighten screws and bolts to their specied tightening torques. Do
not use electric screwdrivers or impact screwdrivers.
Installing the bracket to the projector
Attach the projector mount bracket to the projector (sold separately).
<For the PT-RZ770 / RW730 / RZ660 / RW620 /
RZ970 / RW930 / RX110 / RZ670 / RW630>
1) Place the projector upside-down onto a piece of
soft material.
2) Turn the adjustment leg(s) (see the two points for
PT-RZ670 / RW630 or the one point for
PT-RZ970 / RW930 / RX110 / RZ770 / RW730 /
RZ660 / RW620 in the gure on the left) clockwise
to minimize the length of the legs.
zIf the adjustment legs (see the two points in
the gure on the left) are too long, the projector
mount bracket will come into contact with the
legs, and mounting it onto the projector will not
be possible.
Secure in ve places
Projector mount bracket
3) Firmly secure the projector mount bracket to the
bottom of the projector using the ve supplied
captive washer hex head bolts (M6 × 16) as shown
in the gure on the left.
zUse ve of the six captive washer head bolts
supplied with the unit.
PT-RZ670 / RW630 PT-RZ670 / RW630 / RZ970 /
RW930 / RX110 / RZ770 /
RW730 / RZ660 / RW620
Installation
ET-PKD130B_EN_TQZJ577-7.indd 12 2017/03/13 19:04:55

ENGLISH - 13
<For the PT-DZ870, DW830 and DX100>
1) Place the projector upside-down onto a piece of
soft material.
2) Turn the adjustment leg (see the gure on the left)
clockwise to minimize the length of the leg.
zIf the adjustment leg (see the gure on the left)
is long, the projector mount bracket comes in
contact with the leg and cannot be mounted
onto the projector.
Secure in six places
Projector mount bracket
3) Firmly secure the projector mount bracket to the
bottom of the projector using the six supplied
captive washer hex head bolts (M6 × 16) as shown
in the gure on the left.
Secure in ve places
Projector mount bracket
<For the PT-DZ780 / RZ575 / RZ570 / DW750 /
DX820 / DZ770 / DW740 / DX810 / DZ680 /
DW640 / DX610 / DW730 / DX800 / DZ6710 /
DZ6700 / DW6300 / D6000 / D5000>
1) Place the projector upside-down onto a piece of
soft material.
2) Firmly secure the projector mount bracket to the
bottom of the projector using the ve supplied
captive washer hex head bolts (M6 × 16) as shown
in the gure on the left.
zUse ve of the six captive washer head bolts
supplied with the unit.
Installation (continued)
ET-PKD130B_EN_TQZJ577-7.indd 13 2017/03/13 19:04:58

14 - ENGLISH
Attaching the drop prevention kit to the projector
Attach the drop-prevention wire rope to the projector (sold separately).
Adjustment leg
1) Turn the adjustment leg (one) counterclockwise to
remove it from the projector.
Wire rope
Flat washer
Adjustment leg 2) Pass the supplied at washer (one) and wire
rope through the adjustment leg (one) as
illustrated on the left.
Attention
zBe sure to use the supplied at washers and wire
rope.
3) Turn the adjustment leg clockwise to secure it to
the projector.
Attention
zFor information on how to join this product to the
ceiling mount bracket (ceiling mount bracket for
low or high ceilings) (separately sold) and how
to attach the wire rope in the ceiling, refer to
the installation instructions or other instructions
supplied with the ceiling mount bracket (ceiling
mount bracket for low or high ceilings).
Wire rope
Adjustment leg
zWhen attaching the wire rope to a PT-RZ575 /
RZ570, pull out the wire rope as illustrated on the
left, and tighten the adjustment leg.
Installation (continued)
ET-PKD130B_EN_TQZJ577-7.indd 14 2017/03/13 19:05:02

ENGLISH - 15
Removing the projector from the existing bracket
When combining an existing ET-PKD120H, ET-PKD120S, ET-PKD310H, ET-PKD310S, ET-PKD56H, ET-PKD55S,
ET-PKD100H, ET-PKD100S, ET-PKD77H and ET-PKD75S ceiling mount brackets with this product, you will need
to rst remove the projector from these ceiling mount brackets.
Note
zThe illustration shows an installation using the ET-PKD56H ceiling bracket for high ceilings. Other ceiling
mount brackets for low or high ceilings can be removed according to the same procedure.
zThe illustrations of projectors are for informational purposes only and do not represent a specic model.
Congurations may vary with the model.
1) Remove the wire rope from the ceiling.
2) Remove the two captive washer hex head bolts.
zMake sure the projector is properly supported
from below while doing this.
Hex head bolt,
captive washer
Hook
Angle adjusting
bracket
Pole base
3) Slightly loosen the captive washer hex head bolts
in the hooks and remove the angle adjusting
bracket from the pole base (the attachment plate if
a ceiling mount bracket for low ceilings is used) as
shown in the gure on the left.
Attention
zDo not over-loosen the captive washer hex head
bolts in the hooks. If the bolts become too loose,
the projector could fall down.
WARNING:
Removal must be carried out by two or more
persons.
Hex head bolt,
captive washer
4) Loosen and remove the six captive washer hex
head bolts that secure the angle adjusting bracket
and remove it.
Attention
zThe removed angle adjusting bracket and the captive washer hex head bolts that secured it will be used later.
zWhen the projector and the projector mount bracket are no longer needed, be sure to dispose of them
appropriately.
Using an existing bracket
ET-PKD130B_EN_TQZJ577-7.indd 15 2017/03/13 19:05:03

16 - ENGLISH
Mounting the projector on an existing bracket
To combine this product with an existing ET-PKD120H, ET-PKD120S, ET-PKD310H, ET-PKD310S, ET-PKD56H,
ET-PKD55S, ET-PKD100H, ET-PKD100S, ET-PKD77H and ET-PKD75S, use the steps on pages 12 to 14 to install
this product and the drop prevention kit supplied with the product on the projector. Then install the projector on
the existing ceiling mount bracket according to the following instructions.
Note
zThe illustration shows an installation using the ET-PKD56H ceiling bracket for high ceilings. Other ceiling
mount brackets for low or high ceilings can be installed according to the same procedure.
zThe illustrations of projectors are for informational purposes only and do not represent a specic model.
Congurations may vary with the model.
Angle adjusting
bracket
Projector
mount bracket
Angle adjusting bracket
Hex head bolt, captive washer
Hex head bolt, captive washer
1) Align the screw holes on the angle adjusting
bracket with the holes on the projector mount
bracket and secure the bracket with the six captive
washer hex head bolts removed in the section
“Removing the projector from the existing bracket”,
as shown in the gure on the left.
Attention
zAfter adjusting the installation angle, tighten the six
captive washer hex head bolts rmly.
For information on how to adjust the installation
angle, refer to the installation instructions or other
instructions supplied with the ceiling mount bracket
(for low or high ceilings).
Note
zThe illustration of the angle adjusting bracket is for
informational purpose only and does not represent
a specic product. Tightening positions of the
captive washer hex head bolts may vary depending
on the shape of the angle adjusting bracket.
Using an existing bracket (continued)
ET-PKD130B_EN_TQZJ577-7.indd 16 2017/03/13 19:05:05

ENGLISH - 17
Hex head bolt,
captive washer
Pole base
Hook
2) Fit the nger tightened captive washer hex head
bolts in the pole base (the attachment plate for a
ceiling mount bracket for low ceilings) in the hooks
on the angle adjusting bracket.
Attention
zMake sure that the nger tightened captive washer
hex head bolts are rmly engaged with the thread
ridges of the pole base (the attachment plate if a
ceiling mount bracket for low ceilings is used).
zHold the projector rmly until the captive washer
hex head bolts are securely placed in the hooks on
the angle adjusting bracket.
WARNING:
Mounting and installation must be carried out
by two or more persons.
Hex head bolt,
captive washer
Hex head bolt,
captive washer
3) Use the two captive washer hex head bolts
removed in the section "Removing the projector
from the existing bracket" to secure the pole base
(the attachment plate for a ceiling bracket for low
ceilings) and the angle adjusting bracket as shown
in the gure on the left.
Attention
zAfter mounting the projector on the ceiling mount bracket, adjust the installation angle.
For information on how to adjust the installation angle, refer to the installation instructions or other instructions
supplied with the ceiling mount bracket (for low or high ceilings).
Using an existing bracket (continued)
ET-PKD130B_EN_TQZJ577-7.indd 17 2017/03/13 19:05:06

External dimensions
Width: 378 mm (14-7/8")
Height: 56 mm (2-7/32")
Depth: 400 mm (15-3/4")
Weight Approx. 3 (6.61 lbs.)
SS1013AM7047 –PS
Printed in Japan
https://panasonic.net/cns/projector/
Specications
ET-PKD130B_EN_TQZJ577-7.indd 18 2017/03/13 19:05:07