Panasonic ET-SFD310 User manual

R
Operating Instructions
Commercial Use
Model No. ET-SFD310
Thank you for purchasing a Panasonic product.
Read this manual and the projector manual completely, and use this
product correctly and safely.
All the projector illustrations in this manual are based on PT-DZ8700U and
PT-DZ110XE model.
Before replacing the parts
• Turn off the main power of the projector and remove the power plug from the power
socket when replacing the cartridge.
• Follow the procedures in the “Powering off the projector” section in the projector’s
Operating Instructions manual when turning off the projector.
Attention:
•
•
•
operating problems. (The time of shutting down is shown in minutes.)
Note:
• The <Filter Monitor> of the projector will blink in green and the fan speed will increase
•
•
If it is used for more than approximately 24 hours, operating problems may occur and
inspection or repairs might be required.
•
ambient temperature is 35°C or higher.
Filter
Monitor
TQZJ300-1
ET-SFD310_TDZJ300_EN.indd 1 2010/07/08 15:07:11

2
Installing the smoke filter
(1) Loosen the [ACF unit cover screw] (one screw) until the screw turns
freely and remove the [ACF unit cover].
ACF unit cover
screw
ACF unit cover
Attention:
• Store the [ACF unit cover] carefully after removal.
(2) Remove the [ACF unit] from the projector.
ACF unit
Attention:
• Store the [ACF unit] carefully after removal.
(3) Install the [smoke-cut  lter] according to the procedure shown in
 gures Aand B and secure the [smoke-cut  lter screw] (one screw)
 rmly.
Smoke-cut  lter Smoke-cut  lter screw
A
B
Attention:
• Ensure the stability of the projector and install the smoke-cut  lter in a place
whereby it is safe in case the  lter falls.
• The smoke-cut  lter must be installed before turning on and using the projector.If the
projector is used without the smoke-cut  lter installed, dust and foreign objects may
get inside it and cause operating problems.
ET-SFD310_TDZJ300_EN.indd 2 2010/07/08 15:07:12

3
Changing the fan mode settings
(1) After installing the [smoke-cut lter], turn on the projector and press
<MENU> button. Select [PROJECTOR SETUP] from the [MAIN MENU]
and press <ENTER> button.
MAIN MENU
PICTURE
POSITION
P IN P
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MENU SELECT
SUB MENU
(2) Select [SERVICE PASSWORD] in [PROJECTOR SETUP] Menu and
press <ENTER> button.
PROJECTOR SETUP
REMOTE2 MODE
NO SIGNAL SHUT-OFF
FUNCTION BUTTON
DISABLE
DEFAULT
LENS CALIBRATION
FILTER COUNTER RESET
DATE AND TIME
SAVE ALL USER DATA
LOAD ALL USER DATA
INITIALIZE
SERVICE PASSWORD
MENU SELECT
SUB MENU
(3) Enter [1111] by pressing <1> on the remote control and then press
<ENTER> button in the service password entry screen.
SERVICE PASSWORD
＊＊＊＊


ENTER
〜
INPUT
SET
(4) Press tuto switch from [NORMAL] to [SPECIAL] in the [AIR FILTER]
screen.
AIR FILTER
FILTER TYPE
CHANGE
Attention:
• When you have nished using the smoke-cut lter and changed the ACF unit,
change the [Filter Type] settings from [SPECIAL] to [NORMAL] and ensure that the
<Filter Monitor> is not blinking in green. Operation problems might occur if the lter
settings are not changed.
(5) Press <MENU> button 3 times to escape from the Menu.
ET-SFD310_TDZJ300_EN.indd 3 2010/07/08 15:07:13

Disposal
When discarding this product, please contact your local authorities or dealer
and ask for the correct method of disposal.
SS0710AM1047 -PS
Web Site : https://panasonic.net/cns/projector/
© Panasonic Corporation 2010
ET-SFD310_TDZJ300_EN.indd 4 2010/07/08 15:07:13