Panasonic KX-TD208 User manual

Digital Super Hybrid System
KX-TD208E
This booklet tells you how to install your KX-TD208 quickly and easily
and gives you initial operating instructions.
For further information, see the enclosed "Operating lnstructions."
g
n
i
t
t
e
G
S
t
a
r
t
e
d

CCoonntteennttss
• • • 2 • • •
Preparation
Describes the included
accessories and required
tools for installation.
Page 3Connection
Shows you how to install
your system from set-up to
initial use.
Page 4
Basic
Programming
Describes the programs nec-
essary depending on your
contract and requirements.
Page 6
Programming
Using A Personal
Computer
Shows you a personal comput-
er connection and how to
program by using it.
Page 9
Basic
Operations
Describes how to make and
receive calls in order to
confirm the connections.
Page 8
Assistance
Information
Page 11
IBM is a registered trademark of International Business Machines Corporation.
MS-DOS®is registered trademark of Microsoft Corporation in the United States and/or other countries.
All other trademarks identified herein are the property of their respective owners.

• • • 3 • • •
PPrreeppaarraattiioonn
¢¢Check the package contents. The included materials are:
¢¢Necessary user-supplied tools:
✔Phillips screwdriver and flathead screwdriver
✔Electrician’s pliers
✔Telephone company contract
✔Serial printer cable to connect a PC to the telephone system
✔Telephone sockets to connect the telephone equipment, if required
✔Wire (solid wire) for the extension connection:
Conductor diameter: Ø 0.4 – 0.6mm
Diameter with coating: Ø 0.66 – 1.05mm
D
I
G
I
T
A
L
S
U
P
E
R
H
Y
B
R
I
D
S
Y
S
T
E
M
POWER
Main Unit ... one
AC Cord ... one
ISDN Line Cord ... one
4-pin Plugs* ... eleven
Screws and Washers
... three
Floppy Disk for PC
Programming ... one
Before installing your system
*Do not close
the transparent
part into the black
part before insert-
ing the wires.

CCoonnnneeccttiioonnss
• • • 4 • • •
POWER
D
I
G
I
T
A
L
S
U
P
E
R
H
Y
B
R
I
D
S
Y
S
T
E
M
2. Connect the include
3. Connect the user -
4. Connect the PC to
1. Open the front cove
RS-232C Port
(Serial Interface)
To AC Outlet
Reset Switch
Strip the wire cover
with pliers.
To the "Extension Jack"
User-supplied
Telephone
Socket
ISDN Modular Jack
5. Close the front cove
1.
Extension Jack
4.
Remove the socket
cover with flathead
screwdriver.
You can program the syste
The required operating syste
ISDN Port 2
ISDN Port 1
scre
Preparation
EXTN.1 A
B
PC
socke
cover
POWER
D
I
G
I
T
A
A
L
S
U
P
E
R
H
Y
B
R
I
D
E
S
Y
S
T
E
E
M
Tie together all of the connected cords
and attach them to the wall so that they
cannot be pulled out of the unit.

• • • 5 • • •
ISDN line cord to "ISDN Port 1" and the Telephone socket to the exchange line.
supplied extension line cord to the "Extension Jack" and telephone equipment.
the RS-232C port.
D
I
G
I
T
A
L
S
U
P
E
R
H
Y
B
R
I
D
S
Y
S
T
E
M
POWER
EXTN.
EXTN.
EXTN.
EXTN.
EXTN.
EXTN.
EXTN.
EXTN.
8
7
6
5
4
3
2
1
1. Slide the cover in the direction of the arrow.
2. Tighten the screw.
AC Inlet
Press the transparent part into the
black part firmly.
Insert the other end of the wires
into the hole on the back and
tighten both screws by the driver.
A
B
6
5
4
1
2
3
and connect the AC cord to the AC inlet and AC outlet.
3.
2.
5.
Insert the user-supplied telephone
wires completely into the holes of
the included plugs.
A
B2
5
D
I
G
I
T
A
L
S
U
P
E
R
H
Y
B
R
I
D
S
Y
S
T
E
M
PO WE R
screw
1. Loosen the screw.
2. Slide the cover toward the right
while pressing the " " mark.
data using TD208.EXE file in the included floppy disk on the IBM-PC/AT or compatible personal computer (PC).
OS) is Version 5.0 or later versions of MS-DOS.
hole
A
B
To the Exchange Line
¥The maximum length of the
extension line cords
to the extensions are;
Line Diameter Max. Length
SLT
PT 0.6mm
0.6mm 240m
620m
Note
¥ For installing proprietary telephones,
an optional PT Interface Card
(KX-TD20870CE) should
be installed on your system.
Please refer to the Operating
Instructions for details.
screw

BC
D
• • • 6 • • •
BBaassiiccPPrrooggrraammmmiinngg
Some programming is required for basic operation. Check your contract
with the telephone company and program as needed. The following flow
chart will tell you which programming is required for your system. Please
program your system accordingly.
Your contract is:
1: Point-to-Multi-point
2: Point-to-Point
Do you want to specify
the receiving extension? Does your contract apply
to a DDI service?
Programming type selection
A
1 2
No Yes No Yes
Connect a tone-type single line telephone to jack number 1 for programming.
Check: • Your telephone is on-hook.
• No calls are on hold at your telephone.
Programming
5
1
2
3
4
Password (Default)
Off-hook Dial tone 3
extension no. CLIP/COLP no.
20 digits max. (0 ··· 9)
[404] CLIP / COLP Number Assignment
21 through 28,
31 through 34,
301 through 308
(ISDN ext.),
300 (all ISDN ext.)
4
0
X
4
(Continued)
X – CLIP / COLP Classfication
1 : CLIP no. Business 2 : CLIP no.-Private
3 : COLP no.-Business 4 : COLP no.-Private
: All
Type
Step 2. Program [404] to all the types A, B, C, D.
Step 1. Enter into the programming mode.
Before programming
(1,2, )
ISDN
port no. (1
··· 4, )

• • • 7 • • •
BBaassiiccPPrrooggrraammmmiinngg
[407] Multiple Subscriber Number (MSN) Set
(01···10)
16 digits max.
(0···9)
MSN
location
no.
(01···10)
location
no.
[406] ISDN Configuration
6
4
0
[408]–[409] Extension Ringing Assignment
—Day / Night for ISDN
(21 ... 28, 31...34)
extension no.
0: immediate
1: 1 ring delay
3: 3 rings delay
6: 6 rings delay
9: disable
delayed ring time
Y- Day...8
Night...9
Consecutive entries
(1,2, )
ISDN
port no.
(1,2, )
ISDN
port no.
(1,2, )
ISDN
port no.
(1,2, )
4 0 7
4 0 Y
A B C D
[412] ISDN DDI Number / Extension Number Transformation
20 digits max.
(0···9)
DDI no.
4
1
2
Press Reset Switch.
On-hook
[405] Direct Dialling In
Step 3. Follow the chart according to your programming type .
Step 4. Exit from the programming mode.
1
0
5
2
4
ISDN
port no.
(1,2, )
ISDN
port no.
extension no.
21 through 28,
31 through 34,
301 through 308, 300,
291 through 298
(UCD Group or Ring
Gruop)
Go to Step 4 .
C DA B

BBaassiiccOOppeerraattiioonnss
• • • 8 • • •
Let’s try to make and receive a call in order to confirm the connections.
¢¢Making a call from extension 21 to extension 22
Did it work???
¢¢Calling a Speaking Clock
1. Off-hook.
2. Enter .
3. Dial .
Can you hear the time announcement?
9
Making a call to another extension and receiving it
Making a call to an outside party
At extension 21
1. Off-hook.
2. Dial .
2
2
At extension 22
1. Off-hook.
1
2
3

• • • 9 • • •
¢¢Refer to the following chart for the pin configuration;
HING SYSTEM
EXTN.
EXTN.
EXTN.
EXTN.
EXTN.
EXTN.
EXTN.
EXTN.
8
7
6
5
4
3
2
1
Connect
your personal
computer to the RS-
232C port with the user-
supplied serial printer
cable. The Cable must
be shielded and the
maximum length
is 2 m.
Connection
Circuit
Type
(EIA)
BB
BA
CD
AB
CC
CA
CB
Pin
No.
2
3
4
5
6
7
8
Signal
Name
RXD
TXD
DTR
SG
DSR
RTS
CTS
Pin
No.
2
3
4
5
6
7
8
Port on your system 9-pin port on a PC
PPrrooggrraammmmiinnggUUssiinnggAAPPeerrssoonnaallCCoommppuutteerr

• • • 10 • • •
PPrrooggrraammmmiinnggUUssiinnggAAPPeerrssoonnaallCCoommppuutteerr
You can program the system data using the application software in the included
floppy disk on the IBM-PC/AT or a compatible personal computer. The system pro-
gramming data can be stored either on the floppy disk or on your hard disk.
To use the floppy disk for PC programming, you must have MS-DOS (or equivalent)
version 5.0 or later. A minimum of 450K of free conventional memory is required.
¢¢File Configuration
The file name: TD208.EXE (Execution file)
You may store the following files if desired.
Database file: *.DBF
ASCII file: *.DBA
Screen save file: P208.PRT
£The “*” represents the file name of your choice. (up to 8 characters)
¢¢Setup
1. Insert the floppy disk into drive A.
2. Change the current directory to drive A.
3. Type TD208 after confirming the sign “>” and press the Enter key.
– The initial screen appears.
£After the initial screen appears, you can remove the included disk and insert
a database file disk to save the data.
£If your monitor is monochrome and you cannot see the cursor easily, exit the
programming mode and re-type
TD208/MONO .
£If you need an explanation of the system and its operations, press F4 (Help)
on the initial screen. A Help screen will appear.
£This program is guaranteed to work with MS-DOS only. It is not guaranteed
with MS-DOS in Windows.
Programming
!
!
!
!