Panduit SmartZone EPA126 User manual

1
Version 1. April 2017
SmartZone Gateway EPA126 Troubleshooting Guide
Contents
PDUs..............................................................................................................................................................2
Sensors..........................................................................................................................................................5
SmartZone DCIM not receiving Traps ...........................................................................................................6
Temperature sensor reporting an alarm ......................................................................................................7
Ping works but cannot get into web-interface .............................................................................................8
Gateway EPA126 Reset.................................................................................................................................8
Cannot ping the Gateway EPA126 ..............................................................................................................10
Gateway EPA126 displaying an alarm –Red Alarm LED on........................................................................10
Gateway EPA126 unit has been reset? .......................................................................................................10
Connectivity between Gateway EPA126 and PDU lost...............................................................................11
How to audit Gateway EPA126 activities and changes...............................................................................11
Power A and/or B Feed on Gateway EPA126 are disconnected/powered down.......................................11
When power goes down in the cabinet, how to get access inside the cabinet .........................................12
Panduit Technical Support for SmartZone Gateway EPA126 .....................................................................12

2
Version 1. April 2017
PDUs
Lost Comms
There are two basic reasons why you may see ‘Lost Comms’ messages from PDU ports.
1. The PDU port is enabled, but does not have a PDU physically connected, in which case the port
can be disabled.
2. The connection between the Gateway EPA126 PDU port and the PDU has become defective in
some way.
Resolution
1. PDU Port Enabled but PDU not physically connected
In this situation, the unused PDU ports may be enabled, but not physically connected to a PDU.
Example: a cabinet may contain 2 PDU’s, but all 6 PDU ports may be enabled in the Gateway
EPA126, meaning that the 4 unconnected ports will generate ‘Lost Comms’ alerts.
A. Point your browser at the IP address for the Gateway EPA126 to get to the Gateway EPA126
login page as follows:
B. Login with the relevant credentials
C. Navigate to the Power>Configure screen as shown below:

3
Version 1. April 2017
D. Then select the relevant CFG box next to the PDU port which needs to be disabled.
E. NOTE –If only 2 POU’s are physically connected, to say ports 1 and 4 for example, then ports
2,3,5, and 6 need to be disabled to prevent ‘Lost Comms’ alerts from these ports.
F. Selecting the port will take you to the screen shown below, Set the Device Type field to
Disabled.
This should prevent any further “Lost Comms”alerts from the disabled ports.
2. Physical connection between Gateway EPA126 and PDU is defective
If there is a problem with the physical connection between the Gateway EPA126 PDU port and
the physical PDU, you are likely to see ‘Lost Comms’ alerts from the Gateway EPA126.

4
Version 1. April 2017
If all unused ports have been disabled as described in Resolution 1 above, then the next step is
to check the physical connections.
A. Firstly, check which port is generating the alert by examining the SNMP trap and/or email
notification details. This will show which port is generating the alerts.
B. At the Gateway EPA126 end, check that there is a patch cable connected to the PDU port that is
generating the alert.
C. If the Gateway EPA126 connection is present and is secure, make sure the relevant patch cable
is connected to the PDU monitoring port on the PDU itself.
D. If the above connection looks good, check that the LCD panel on the PDU is lit and displaying
values. If it is not, replace the patch cable between the PDU and the Gateway EPA126.
E. If replacing the cable does not resolve the issue, then there may be a more significant hardware
issue. Report this to Panduit Technical Support at [e-mail] to get advice
regarding next steps.

5
Version 1. April 2017
Sensors
“Lost Comms”
There are two basic reasons why you may see “Lost Comms” messages from Sensor ports.
1. The Sensor port is enabled but does not have a Sensor physically connected, in which case the
port can be disabled.
2. The connection between the Gateway EPA126 Sensor port and the Sensor has become defective
in some way.
Resolution
1. Sensor Port Enabled but Sensor not physically connected
In this situation, the unused Sensor ports may be enabled but not physically connected to a Sensor.
Example: a cabinet may contain 3 Temperature Sensors, but all 6 Sensor ports may be enabled in
the Gateway EPA126 for Temperature Sensors, meaning that the 3 unconnected ports will generate
‘Lost Comms’ alerts.
A. point your browser at the IP address for the Gateway EPA126 to get to the Gateway EPA126
login page as follows:
B. Login with the relevant credentials
C. Navigate to the Input Sensors>Configure screen as shown below:

6
Version 1. April 2017
D. Select the relevant CFG box next to the Sensor port which needs to be disabled.
E. Selecting the port will take you to the screen shown below. Set the Device Type field to Auto
Detect.
This should prevent any further “Lost Comms”alerts from the Unused ports.
SmartZone DCIM not receiving Traps
–Symptoms:

7
Version 1. April 2017
SmartZone DCIM is not receiving events/alarms or health status from Gateway EPA126
–Action:
•Check if Gateway EPA126 has any active events
•Check if the Enable flag has been turned off in Input Sensors>Configure screen
•Check Gateway EPA126 SNMP Rec’rs tab and verify IP, Community strings, and
Access
•Send a test alarm to the SNMP receiver
Temperature sensor reporting an alarm
–Symptoms:
A red icon or amber icon or is missing for a sensor
–Action:
•Check thresholds setting for the specific sensor to make sure it is in range of
Panduit specs
•Ensure that sensor patch cord is connected properly
•Verify that sensor is detected by Gateway EPA126 as a temperature type
•Check if sensor name ‘Channel’ matches with sensor type
•Ensure sensor is in Enabled state
•Switch the sensor to an empty port, 11 or 12 on Gateway EPA126, and check if
the problem persists
•Sensor may have been damaged/malfunctioning. Contact Panduit System
Support

8
Version 1. April 2017
Ping works but cannot get into web-interface
–Symptoms:
Gateway EPA126 can be pinged but cannot access web interface
–Action:
•Usually a transitional state
•Soft reset the Gateway EPA126 via reset button on the Gateway EPA126 front or
rear
•Wait for 1-1.5min for web interface to initialize
•Check firewall settings on the browser
•If problem persists, contact Panduit System Support as a hard-reset may be
required due to a firmware fault
Gateway EPA126 Reset
–Gateway EPA126 hard-reset
•If Gateway EPA126 is not responsive after a soft reset, as a last resort, a factory
reset can be performed under supervision of Panduit System Support
•SmartZone Gateway EPA126 configuration will be overwritten
•No impact to power outlets –power supply to devices
•Need to Restore SmartZone spec
•Recommended to be done with Panduit System Support

9
Version 1. April 2017

10
Version 1. April 2017
Cannot ping the Gateway EPA126
–Symptoms:
Cannot ping the Gateway EPA126 or cannot contact/reach Gateway EPA126
–Action:
•Check speed and link LED on Gateway EPA126 front interface are on (speed
should be sold and link LED may be blinking)
•Make sure network connection to Gateway EPA126 is good/stable - Gateway
EPA126 to switch
•Confirm if switch port supports 10/100 speed
•Ensure that your computer has access to network segment of the Gateway
EPA126 IP segment
Gateway EPA126 displaying an alarm –Red Alarm LED on
–Symptoms:
Gateway EPA126 show a red alarm LED in front and rear of the Gateway EPA126
–Action:
•This is an indication of a sensor showing value exceeding the set threshold limit
•Log into the Gateway EPA126 and check the Input Sensor screen for ‘Value’ vs
the ‘Limits’ fields
•Based on the threshold violation, Panduit may have a policy in place for
recommended action (for example, what action to recommend to client if temp
is showing more than 95°F at ‘RD M Temp’ sensor). The recommendation could
be to lower the set point of the CRAC/CRAH or adjust air dampeners, etc.
Gateway EPA126 unit has been reset?
–Symptoms:
Gateway EPA126 seems not working per spec, or configuration does not match default
–Action: