ParaBody 841101 User manual

841101 WEIGHT STACK OPTION
CLASSH
PART # 6754401
REV.A
Version: 841101
Revision: 06/19/01
1
ASSEMBLY INSTRUCTIONS

IMPORTANT NOTES
Please note:
Tools Required forAssembly
* Thank you for purchasing the Parabody 841101 WEIGHT STACK OPTION. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled on
a flat, level surface to assure its proper function.
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* Tape measure
2
NOTE:BOLTLENGTHISMEASURED FROMTHEUNDERSIDEOFTHEHEADOFTHE BOLT.
BOLT LENGTH RULER:
We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your Parabody customer service representative
at [phone].
BoltLengthRuler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
WELCOMETOTHEWORLDOF Serious steel!
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
2. Do not allow minors or children to play on or around this equipment.
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
3. Exercise with care to avoid injury.
4. If unsure of proper use of equipment, call your local Parabody distributor or call the
Parabody customer service department at [phone].
BOLT LENGTH
5. Consult a physician before beginning any exercise program.

3
PARTS LIST
PART #
6750803
6753703
6274402
6275302
6609002
6610402
6750503
6176201
6754501
6189501
3116101
3116201
6284501
6714601
6758701
6577701
6542402
3103102
3108002
6595201
3117401
6467001
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
QTY
1
1
1
1
1
1
1
2
2
1
1
6
1
1
1
1
2
4
2
2
4
1
PART #
3102901
3102933
3102922
3102904
3102915
3102910
3102502
3102801
3102501
3102802
6480301
6692601
3119301
6405201
6236701
6177001
6214401
3013801
6075906
6382301
6214501
DESCRIPTION
3/8 X 1-1/4” BOLT
3/8 X 2” BOLT
3/8 X 2-3/4” BOLT
3/8 X 3” BOLT
3/8 X 3-1/4” BOLT
1/2 X 3” BOLT
1/2” WASHER
1/2” LOCK NUT
3/8” WASHER
3/8” LOCK NUT
3/8” FLANGE SPACER
3 X 2” END CAP
2-1/2” ROUND END CAP
2” SQ. END CAP
1-3/4” SQ. END CAP
NON-SKID STRIP
SELECTOR PIN
5/16” SNAP LINK
12 LINK CHAIN
PLATE BUSHING 10 CT
WEIGHT PLATE
QTY
1
2
6
2
2
4
4
3
11
12
10
2
2
2
1
2
1
3
1
4
20
DESCRIPTION
UPRIGHT
TOP BOOM
LOW ROW BAR
LAT BAR
LOW ROW ATTACHMENT
KNEE SUPPORT
WEIGHT STACK BASE
ROLLER PAD
79-1/2” GUIDE ROD
WEIGHT STACK LABEL
4-1/2” PULLEY
3-1/2” PULLEY
WEIGHT STACK SHAFT
HEAD PLATE
LAT CABLE
LOW ROW CABLE
1-3/4” X 5-1/4” PLATE
1 X 8” GRIP
WEIGHT STACK CUSHION
GUIDE ROD BUSHING
CAP PLUG
2” SQ COVER CAP
KEY
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
FIGURE 1
STEP 1:
• Insert two 2-1/2” ROUND END CAPS (35) to the LOW ROWATTACHMENT (5) as shown in FIGURE 1.
• Attach two NON-SKID STRIPS (38) to the LOW ROW ATTACHMENT (5) as shown in FIGURE 1.
5
38 35

4
FIGURE 2
STEP 2:
• SECURELY assemble the LOW ROWATTACHMENT (5) and the UPRIGHT (1) to the POWER RACK using two 3/8 X 3-1/4”
BOLTS (27), four 3/8” WASHERS (31), and two 3/8” LOCK NUTS (32). See FIGURE 2.
0123456
1/2 1/2 1/2 1/2 1/2 1/2
1
36
5
31
32
POWER RACK
• Insert two 2” SQ ENDCAPS (36) into the ends of the UPRIGHT (1) as shown in FIGURE 2.
3/8 X 3-1/4” 27
31
36

5
FIGURE 4
• Insert two WEIGHT PLATE BUSHINGS (42) into
the “PARABODY” side of each of the twenty
WEIGHT PLATES (43) as shown in FIGURE 4.
STEP 4
43
42
FIGURE 3
STEP 3
• Slide one 2” SQ. COVER CAP (22) over the end of the WEIGHT STACK BASE (7) as shown in FIGURE 3.
• SECURELY assemble the WEIGHT STACK BASE (7) to the UPRIGHT (1) using two 1/2 X 3” BOLTS (28), two 1/2” WASH-
ERS (29), and two 1/2” LOCK NUTS (30) as shown in FIGURE 3.
29
30
22
1/2 X 3” 28
7
1

6
• Insert four CAP PLUGS (21) into the bottom end & top end of the two GUIDE RODS (9) as shown in FIGURE 5.
STEP 5:
FIGURE 5
9
31
23 3/8 X 1-1/4” 13
43
10
21
7
19
14
21
• Insert two GUIDE RODS (9) into the WEIGHT STACK BASE (7) as shown on FIGURE 5. (NOTE: Lubricate GUIDE RODS
(9) with silicon or teflon spray available at most hardware stores.)
• Slide two WEIGHT STACK CUSHIONS (19) down over the GUIDE RODS (9).
• Securely assemble the WEIGHT STACK SHAFT (13) to the HEAD PLATE (14) using one 3/8 X 1-1/4” BOLT (23) and one 3/8”
WASHER (31).
• Using EXTREME CARE slide all twenty WEIGHT PLATES (43) down over the GUIDE RODS (9) on to the WEIGHT STACK
CUSHIONS (19). Make sure that the keyholes of the WEIGHT PLATES (43) are all facing the right way.
• Attach the WEIGHT STACK LABELS (10) to the WEIGHT STACK. Also insert the WEIGHT STACK SELECTOR PIN (39) into
the first WEIGHT PLATE (43) of the WEIGHT STACK.
• CAREFULLY slide the HEAD PLATE ASSEMBLY down over the GUIDE RODS (9) onto the WEIGHT STACK.
39

7
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• SECURELY assemble two 3-1/2” PULLEYS (12) to the TOP BOOM (2) using two 3/8 X 2-3/4” BOLTS (25), four 3/8”
FLANGE SPACERS (33), and two 3/8” LOCK NUTS (32). See FIGURE 6. (NOTE: BEFORE TIGHTENING, MAKE SURE
CABLE (15) IS IN THE GROOVES OF THE PULLEYS.)
STEP 6:
• Insert two 2 X 3” END CAPS (34) into the TOP BOOM (2) as shown in FIGURE 6.
• Route threaded end of the LAT CABLE (15) through the TOP BOOM (2) as shown in FIGURE 6.
FIGURE 6
• Insert two GUIDE ROD BUSHINGS (20) into the BUSHINGS of the TOP BOOM (2) as shown in FIGURE 6.
2
FIGURE 7
STEP 7
• LOOSELY assemble two 3-1/2” PULLEYS (12) to two 1-3/4” X
5-1/4” PLATES (17) using two 3/8 X 2” BOLTS (24) and two 3/8”
LOCK NUTS (32) as shown in FIGURE 7.
24 3/8 X 2”
12
17
34
15
12
32
20
32
33
33
25 3/8 X 2-3/4”

8
STEP 8:
FIGURE 8
• SECURELY assemble two 3-1/2” PULLEYS (12) to the TOP BOOM (2) using two 3/8 X 2-3/4” BOLTS (25), four 3/8”
FLANGE SPACERS (33), and two 3/8” LOCK NUTS (32). See FIGURE 8. (NOTE: BEFORE TIGHTENING, MAKE SURE
CABLE (15) IS IN THE GROOVES OF THE PULLEYS.)
• Route threaded end of the LAT CABLE (15) around the one of the PULLEYS in PLATE & PULLEY ASSEMBLY (17) and
through the holes in the TOP BOOM (2) as shown in FIGURE 8.
2
17
12
15
32
33
25 3/8 X 2-3/4”

9
STEP 9:
FIGURE 9
• Swing the GUIDE RODS (9) under the TOP BOOM (2) as shown on FIGURE 9.
• Assemble the TOP BOOM (2) over the GUIDE RODS (9) and SECURELY assemble the TOP BOOM (2) to the UPRIGHT (1)
using two 1/2 X 3” BOLTS (28), two 1/2” WASHERS (29), and one 1/2” LOCK NUT (30). See FIGURE 9.
• SECURELY assemble the TOP BOOM (2) to the top of the POWER RACK using two 3/8 X 3” BOLTS (26), four 3/8” WASH-
ERS (31), and two 3/8” LOCK NUTS (32). See FIGURE 9.
• Screw the threaded end of the LAT CABLE (15) approximately 3/4” into the end of the WEIGHT STACK SHAFT (13) and tighten
jam nut securely. See FIGURE 9.
15
13
31
3/8 X 3” 26
1
2
32
9
1/2 X 3” 28
30
29
POWER RACK

10
FIGURE 10
STEP 10:
3/8 X 2-3/4” 25
• Loop the ball end of the LOW ROW CABLE (16) around one 4-1/2” PULLEY (11) and SECURELY assemble the 4-1/2” PUL-
LEY (11) to the UPRIGHT (1) using two 3/8 X 2-3/4” BOLTS (25), two 3/8” FLANGE SPACERS (33), two 3/8” WASHERS
(31), and two 3/8” LOCKNUTS (32). (NOTE: Make sure CABLE is routed between the PULLEY and the retaining bolt as
shown in FIGURE 10.)
16
31
33
32
1
11