Parkside 306948 User manual

IAN 306948
CORDLESS ROTARY TOOL PFBS 12 B2
CORDLESS ROTARY TOOL
Translation of the original instructions
AKKU-FEINBOHRSCHLEIFER
Originalbetriebsanleitung
ΕΠΑΝΑΦΟΡΤΙΖΟΜΕΝΗ ΣΥΣΚΕΥΗ
ΛΕΙΑΝΣΗΣ ΚΑΙ ΔΙΑΤΡΗΣΗΣ
Μετάφραση των αυθεντικών οδηγιών λειτουργίας

GB/IE/NI/CY Translation of the original instructions Page 1
GR/CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 17
DE/AT/CH Originalbetriebsanleitung Seite 33
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες
της συσκευής.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.

B
A

PFBS 12 B2 GB│IE│NI│CY │ 1 ■
Contents
Introduction......................................................2
Intended use................................................................ 2
Features ................................................................... 2
Package contents ............................................................ 2
Technical details............................................................. 2
General power tool safety warnings .................................3
1. Work area safety.......................................................... 3
2. Electrical safety ........................................................... 4
3. Personal safety............................................................ 4
4. Power tool use and care .................................................... 5
5. Use and handling of the cordless electrical power tool............................. 5
6. Service .................................................................. 5
Safety instructions for all applications ............................................ 6
Additional safety instructions for all applications .................................... 7
Supplementary safety instructions for grinding and abrasive cutting ..................... 8
Supplementary safety instructions for working with wire brushes. . . . . . . . . . . . . . . . . . . . . . . . 9
Safety guidelines for battery chargers ............................................ 9
Use .............................................................9
Charging the integrated battery................................................ 10
Checking the battery charge level ..............................................10
Changing/inserting the tool/collet chuck. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Switching on and off/setting speed range........................................ 10
Notes on working with materials/tools/speed range ............................... 10
Tips and tricks.............................................................. 12
Maintenance and cleaning.........................................12
Disposal........................................................13
Kompernass Handels GmbH warranty ..............................13
Service .........................................................14
Importer .......................................................14
Translation of the original Conformity Declaration .....................15

PFBS 12 B2
■ 2 │ GB│IE│NI│CY
CORDLESS ROTARY TOOL
PFBS 12 B2
Introduction
Congratulations on the purchase of your new appli-
ance. You have chosen a high-quality product. The
operating instructions are part of this product. They
contain important information about safety, usage
and disposal. Before using the product, please
familiarise yourself with all operating and safety
instructions. Use the product only as described and
for the range of applications specified. Please also
pass these operating instructions on to any future
owner.
Intended use
This cordless precision drill/sander is intended for
drilling, milling, engraving, polishing, cleaning,
grinding, cutting of materials such as wood, metal,
plastics, ceramics and stone in dry rooms using
the corresponding attachments (as supplied). Any
other usage of or modification to the appliance is
deemed to be improper and carries a significant
risk of accidents. The manufacturer accepts no
responsibility for damage(s) attributable to misuse.
This appliance is not intended for commercial use.
Features
Cordless precision drill/sander:
Speed control
Battery LED
On/Off switch
Charging socket
Tensioning nut
Union nut
Spindle lock
Battery charger (see Fig. A):
Charger
Accessories (See Fig. B):
6 HSS drill bits
2 mandrels as tool holders
3 polishing discs
4 grinding discs
1 metal brush
16 cutting discs
5 collet chucks
2 synthetic brushes
3 milling bits
2 engraving bits
5 grinding bits
1 combination spanner
Package contents
1 cordless rotary tool
1 charger
1 accessories set (50 pieces)
1 set of operating instructions
Technical details
Model PFBS 12 B2:
Rated voltage: 12 V (DC)
Rated idle speed: n 5000–25000 rpm
Max. disc ø: 25mm
Chuck clamping
range: max. ø 3.2 mm
Capacity: 1300 mAh
Battery (integrated): LITHIUM-ION
Cells: 3
Charger PFBS 12 B2-2:
Primary (input):
Rated voltage: 100–240 V∼, 50–60 Hz
(AC)
Rated power
consumption: 0.25 A
Secondary (output):
Rated voltage: 12.6 V (DC)
Rated current: 500 mA

PFBS 12 B2 GB│IE│NI│CY │ 3 ■
SMPS – switched-mode
power supply
Charging time: approx. 3 hours
Safety transformer,
short-circuit-proof
Protection class: II/ (double insulation)
Polarity:
Protection type IP20
Protection against solid
objects with a diameter of
more than 12.5 mm
Max. Ambient temperature: ta: 40°C
Noise emission value:
Noise measurement value determined in accord-
ance with EN 60745. The A-rated noise level of
the power tool is typically as follows:
Sound pressure level: LpA = 61.8 dB (A)
Uncertainty: KpA = 3 dB
Sound power level: LWA = 72.8 dB (A)
Uncertainty K: KWA = 3 dB
Wear hearing protection!
Total vibration value:
ah, SG = 1,216 m/s2
Uncertainty K: 1.5 m/s2
NOTE
► The vibration level specified in these instruc-
tions has been measured in accordance with
a standardised measuring procedure and
can be used for equipment comparisons. The
specified vibration emission value can also
be used to make an initial exposure estimate.
WARNING!
► The vibration level varies depending on the
use of the power tool and may be higher
than the value specified in these instructions
in some cases. Regular use of the power tool
in this way may cause the user to underesti-
mate the vibration. Try to keep the vibration
loads as low as possible. Measures to reduce
the vibration load are, e.g. wearing gloves
and limiting the working time. Wherein all
states of operation must be included (e.g.
times when the power tool is switched off and
times where the power tool is switched on but
running without load).
General power tool
safety warnings
WARNING!
► Read all safety warnings and all
instructions. Failure to follow the
warnings and instructions may result
in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.

PFBS 12 B2
■ 4 │ GB│IE│NI│CY
2. Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment.
Always wear eye protection.
Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising
power tools that have the switch on invites
accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.

PFBS 12 B2 GB│IE│NI│CY │ 5 ■
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that can-
not be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have
the power tool repaired before use. Many
accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
5. Use and handling of the cordless
electrical power tool
a) Charge a rechargeable battery unit using
only the charger recommended by the
manufacturer. Chargers are often designed
for a particular type of rechargeable battery
unit. There is the danger of fire if other types of
rechargeable battery units are used.
b) Only the rechargeable battery units supplied
are to be used with an electrical power tool.
The use of other rechargeable battery units may
lead to the danger of injury or fire.
c) When they are not being used, store
rechargeable battery units away from paper-
clips, coins, keys, nails, screws or other small
metal objects that could cause the contacts
to be bridged. Short-circuiting the contacts of
a rechargeable battery unit may result in heat
damage or fire.
d) Fluids may leak out of rechargeable battery
units if they are misused. If this happens,
avoid contact with the fluid. If contact occurs,
flush the affected area with water. Seek addi-
tional medical help if any of the fluid gets into
your eyes. Escaping battery fluid may cause
skin irritation or burns.
CAUTION! RISK OF EXPLOSION!
Never charge non-rechargeable
batteries.
Protect the rechargeable battery from
heat; for example, from continuous
exposure to sunlight, fire, water and
moisture. There is a risk of explosion.
6. Service
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.

PFBS 12 B2
■ 6 │ GB│IE│NI│CY
Safety instructions for all applica-
tions
General safety instructions for grinding, sand-
paper sanding, working with wire brushes,
polishing, milling and abrasive cutting:
a) This power tool is intended for use as a grinder,
sandpaper sander, wire brush, polisher, milling
machine and abrasive cutting machine.
Please follow all safety instructions, instruc-
tions, diagrams and data that you receive
with the appliance. If you do not observe the
following instructions, this can lead to electrical
shock, fire and/or serious injuries.
b) Do not use any accessories that have not
been provided or recommended by the manu-
facturer for this power tool. Just because you
can attach the accessories to your power tool,
does not ensure they are safe to use.
c) The permissible speed of the accessory tool
used must be at least as high as the maximum
speed specified for the power tool. Accessories
that rotate faster than the permissible rate can
break and throw pieces into the air.
d) The external diameter and thickness of the
accessory tool used must comply with the
dimensions of your power tool. Incorrectly
dimensioned accessory tools cannot be suffi-
ciently shielded or controlled.
e) Grinding discs, sanding drums or other acces-
sories must match the grinding spindle or
collet chuck of your power tool exactly.
Accessory tools which do not fit precisely into
the take-up of the power tool will rotate unevenly,
vibrate severely and can lead to a loss of control.
f) Discs, grinding cylinders, cutting tools or
other accessories mounted on a mandrel must
be completely inserted in the collet or chuck.
Any "protrusion" or exposed parts of the
mandrel between the grinding tool and the
collet or chuck must be kept to a minimum. If
the mandrel is not sufficiently tightened or the
grinding tool protrudes too far, the tool could
come loose and be thrown out at high speed.
g) Never use damaged accessory tools. Before
each use, check accessory tools such as
grinding discs for chips or cracks, sanding
drums for cracks or excessive wear and tear
and wire brushes for loose or broken wires.
If the power tool or the accessory tool in use
is dropped, check to see if it is damaged or
use an undamaged accessory tool. When
you have checked and inserted the accessory
tool, ensure that you and any other people
in the vicinity remain outside of the range of
the rotating accessory tool and allow the tool
to rotate at maximum speed for one minute.
Damaged accessory tools usually break during
this test period.
h) Wear personal protective equipment.
Depending on the application, ensure that
you use full face protection, eye protection
or goggles. If required, use a dust mask, ear
protectors, protective gloves or a special
apron to protect you from grindings and
material particles. Protect your eyes from
flying debris that may be created during certain
applications. Dust or filter masks must be used
to filter any dust created by the application.
If you are exposed to loud noise for any length
of time, you may suffer hearing loss.
i) Ensure that other people remain at a safe
distance from your workspace. Anyone who
enters the workspace must wear personal
protective equipment. Fragments of the work-
piece or broken accessory tools can fly off
and cause injury – even outside the immediate
working area.

PFBS 12 B2 GB│IE│NI│CY │ 7 ■
j) Hold the power tool only by the insulated
gripping surfaces when performing an oper-
ation where the accessory tool may contact
hidden wiring or its own cord. Contact with
a live cable can also make metal parts of the
appliance live and could result in an electric
shock.
k) Always hold the power tool firmly. When
running up to full speed, the torque of the motor
can cause the power tool to twist.
l) If possible, use clamps to hold the workpiece
in position. Never hold a small workpiece
in one hand and the power tool in the other
while you are using it. By clamping small
workpieces, you keep both hands free for better
control of the power tool. When cutting round
workpieces such as dowels, rods or pipes, be
aware that these can roll away and this can
cause the tool to jam and be thrown towards
you.
m) Hold the power cord away from any rotating
accessories. If you lose control of the appli-
ance, the cord may get cut or caught and your
hand or arm could get caught in the rotating
accessory tool.
n) Never put the power tool down until the
accessory tool has come to a complete stand-
still. The rotating accessory tool can come into
contact with the surface and cause you to lose
control of the power tool.
o) When changing accessory tools or changing
settings, tighten the collet nut, the chuck or
other fixing elements tightly. Loose fastening
elements can shift unexpectedly and lead to
loss of control; unsecured, rotating components
will fly off violently.
p) Do not leave the power tool running whilst
carrying it. Accidental contact between your
clothing and the rotating accessory tool could
lead to physical injury.
q) Clean the ventilation slits of your power tool
regularly. The engine fan draws dust into the
housing and a strong accumulation of metal
dust can cause electrical hazards.
r) Do not use the power tool in the vicinity of
flammable materials. Sparks can ignite such
materials.
s) Do not use any accessory tools which require
liquid coolant. The use of water or other liquid
coolants may lead to electric shock.
Additional safety instructions for all
applications
Kickback and corresponding safety instruc-
tions
Kickback is a sudden reaction caused when a
rotating accessory tool, e.g. grinding disc, grinding
band, wire brush, etc., catches or jams and leads
to an abrupt stop of the rotating accessory tool.
If this happens, an uncontrolled power tool will
turn rapidly against the direction of rotation of the
accessory tool.
If, for example, a grinding disc catches or jams,
the edge of the grinding disc that is projecting into
the workpiece can get caught and break off the
grinding disc or cause a kickback. The grinding
disc can then fly in the direction of the operator
or away from him, depending on the direction of
rotation of the disc at the blockage. This can also
break grinding discs.
A kickback is caused by improper or incorrect use
of the power tool. This can be avoided by taking
proper precautions as described below.

PFBS 12 B2
■ 8 │ GB│IE│NI│CY
a) Hold the power tool firmly in both hands
and position your body and arms so they
can absorb the force of a kickback. By taking
adequate precautions, the operator can stay in
control of the kickback forces.
b) Take special care when working on corners,
sharp edges, etc. Avoid allowing the accessory
tool to bounce back from the workpiece or
jam in the workpiece. The rotating accessory
tool is more likely to jam in corners or sharp
edges or if it rebounds off them. This can cause
a loss of control or kickback.
e) Do not use toothed saw blades. Such acces-
sories often cause a kickback or loss of control
over the power tool.
d) Always move the accessory tool in the same
direction in the material in which the cutting
edge leaves the material (in other words, the
same direction in which the dust is thrown
out). Guiding the power tool in the wrong direc-
tion will cause the cutting edge of the accessory
tool to jump out of the workpiece which can
lead to the accessory tool being pulled in this
direction.
e) Always clamp the workpiece when using
rotary files, cutting discs, high-speed milling
tools or hard-metal tools. Even a minimal tilting
in the groove can cause these tools to jam and
lead to a kickback. When a cutting disc jams, it
usually breaks. When a rotary file, high-speed
milling tool or hard-metal milling tool jams, the
accessory tool can jump out of the groove and
lead to loss of control of the power tool.
Supplementary safety instructions
for grinding and abrasive cutting
Special safety instructions for grinding and
abrasive cutting:
a) Use only the grinding accessories approved
for your power tool and only for the recom-
mended applications. Example: Never grind
with the side surface of a cutting disc. Cutting
discs are designed to remove material with
the edge of the disc. Any lateral application
of force on these grinding tools can lead to
breakage.
b) For conical and straight pencil grinders, use
only undamaged mandrels of the correct
size and length and without an undercut on
the shoulder. Using an appropriate mandrel
reduces the risk of breakages.
c) Avoid cutting disc jams or excessive contact
pressure. Do not make any excessively deep
cuts. Overloading the cutting disc increases the
stress and likelihood of tilting or jamming and
thus the possibility of kickback or breakage of
the grinding tool.
d) Avoid putting your hand in the area in front
of or behind the rotating cutting disc. When
you move the cutting disc away from your hand,
it is possible, in the event of a kickback, that the
power tool (along with the rotating disc) could
be thrown out directly towards you.
e) If the cutting disc jams or you stop working,
switch the tool off and hold it steady until the
disc has completely stopped turning. Never
attempt to pull a rotating cutting disc out of a
cut. This could lead to kickback. Identify and
remove the cause of the jam.
f) Do not switch the power tool back on while it
is still in the workpiece. Allow the cutting disc
to reach its full speed before you carefully
resume the cut. Otherwise, the disc may jam,
jump out of the workpiece or cause kickback.

PFBS 12 B2 GB│IE│NI│CY │ 9 ■
g) Support panels or large workpieces to
reduce the risk of the cutting disc jamming
and causing a kickback. Large workpieces can
bend under their own weight. The workpiece
must be supported on both sides, namely in the
vicinity of the cut, and also at the edge.
h) Be particularly careful when making "pocket
cuts" into existing walls or other obscured
areas. The inserted cutting disc may cut into
gas or water pipes, electrical wiring or other
objects that can cause kickback.
Supplementary safety instructions
for working with wire brushes
Special safety instructions for working with
wire brushes:
a) Be aware that the brush can lose wire bristles
even during normal operation. Do not
overstress the wires by applying excessive
pressure to the brush. The wire bristles can
easily penetrate light clothing and/or skin.
b) Allow the brush to run at working speed for
at least one minute before applying it to the
workpiece. Ensure that no one is standing in
front of or in line with the brush during this
time. Loose pieces of wire can fly off during the
run-in period.
c) Aim the rotating steel brush away from your-
self. When working with these brushes, small
particles and minute pieces of wire can fly off at
great speed and pierce skin.
Safety guidelines for battery chargers
■ This appliance may be used by chil-
dren aged 8 years and above and
by persons with limited physical,
sensory or mental capabilities or
lack of experience and knowledge,
provided that they are under super-
vision or have been told how to use
the appliance safely and are aware
of the potential risks. Do not allow
children to use the appliance as a
toy. Cleaning and user maintenance
tasks may not be carried out by
children unless they are supervised.
■ To avoid potential risks, damaged
mains cables should be replaced
by the manufacturer, their customer
service department or a similarly
qualified person.
The charger is suitable for indoor use
only.
WARNING!
■ Do not operate the appliance with a dam-
aged cable, power cord or mains plug.
A damaged power cord poses a threat of
fatal electric shock.
Use
■Never use the appliance for other purposes
and use it only with original parts/acces-
sories. Using attachments or accessory tools
other than those recommended in the operating
instructions can lead to a risk of injury.

PFBS 12 B2
■ 10 │ GB│IE│NI│CY
Charging the integrated battery
NOTE
► A new battery or a battery which has not
been used for a long time will need to be
charged before first use/reuse. It will reach its
full capacity after 3–5 charge cycles.
The charging process lasts around 180
minutes.
Starting charging:
♦ Connect the charger to the charging socket
on the appliance.
♦ Connect the charger to a mains power
socket.
The battery is fully charged when the battery
LED shows RED/ORANGE/GREEN.
Stopping charging:
♦ Disconnect the charger from the mains
power supply.
♦ Disconnect the charger from the charging
socket on the appliance.
CAUTION!
► Never recharge a battery again immediately
after charging. There is a risk that the battery
will become overcharged.
Checking the battery charge level
If the appliance is switched on, the remaining
charge will be shown on the battery LED as
follows:
RED/ORANGE/GREEN = maximum charge
RED/ORANGE = medium charge
RED = low charge – charge the battery
Changing/inserting the tool/collet
chuck
♦ Press the spindle lock and hold it down.
♦ Turn the tensioning nut until the lock clicks
into place.
♦ Undo the tensioning nut from the thread
using the combination spanner .
♦ Remove any attached tool.
♦ First push the intended tool through the tensioning
nut before inserting it into the appropriate
collet chuck for the tool shaft.
♦ Press the spindle lock and hold it down.
♦ Push the collet chuck into the thread insert
and screw the tensioning nut tight with the
combination spanner .
NOTE
► Use the screwdriver side of the combination
spanner to undo and tighten the screw on
the mandrel .
Switching on and off/setting speed
range
Switching on/setting the speed range:
♦ Set the On/Off switch to the position "I".
♦ Set the speed control to a position between
"1" and "MAX".
Switching off:
♦ Set the On/Off switch to the position "O".
Notes on working with materials/
tools/speed range
■ Use the milling bits for working on steel and
iron at maximum speed.
■ Determine the rotational speed range for working
on zinc, zinc alloys, aluminium and copper by
trying it out on test pieces.
■ Use a low rotational speed for work on plastics
and materials with a low melting point.
■ Use a high rotational speed for working on
wood.
■ Carry out cleaning, polishing and buffing work
in the medium speed range.
The following are recommendations only and not
binding. When carrying out practical work, carry
out your own tests to see which tool and which
settings are ideal for the material you are working
on.

PFBS 12 B2 GB│IE│NI│CY │ 11 ■
Set a suitable rotational speed:
Number on the speed
control
Material being worked
1–3 Plastics and materials
with a low melting
point
6Hardwood
4–5 Stone, ceramics Max Steel
5Soft wood, metal
Application examples/selecting a suitable tool:
Function Accessories Use Protrusion
(min–max) mm
Drilling HSS drills Working wood 18–25, using the
smallest drill, the
protrusion is 10 mm
Milling Milling bit Various jobs; e.g. creat-
ing recesses, hollows,
forms, grooves or slits
18–25
Engraving Engraving bits Labelling, handicrafts 18–25
Polishing, rust removal
CAUTION!
Exert only a light pres-
sure when applying the
tool to the workpiece.
Metal brush Rust removal 9–15
Polishing discs Various metals and plas-
tics, especially precious
metals such as gold and
silver
12–18
Cleaning Synthetic brushes e.g. cleaning hard-to-
access plastic housings
or the area around a
door lock
9–15
Grinding Grinding discs Grinding work on
stone, wood, fine work
on hard materials such
as ceramics or alloyed
steel
12–18
Grinding bits 10
Cutting Cutting discs Working metal, plastic
and wood
12–18

PFBS 12 B2
■ 12 │ GB│IE│NI│CY
■ The maximum diameter of the assembled grind-
ing bodies, grinding cones, pencil grinders with
a thread insert may not exceed 55mm.
The maximum diameter of sandpaper grinding
accessories may not exceed 80mm.
NOTE
► The max. permissible length of a mandrel is
33 mm.
■ Store the accessories in the original box or store
the accessory components somewhere else to
protect them from damage.
■ Store the accessories somewhere dry and not in
the vicinity of aggressive media.
Tips and tricks
■ If you exert too much pressure, the fitted tool
can break and/or the workpiece could be dam-
aged. You will achieve optimum working results
by moving the tool over the workpiece at a
steady speed and while exerting light pressure.
■ When carrying out cutting work, hold the appli-
ance firmly with both hands.
■ Observe the data and the information in the
table to prevent the end of the spindle from
touching the perforated base of the grinding
tool.
Maintenance and cleaning
The appliance is maintenance-free.
■ Remove all dirt from the appliance. Use a dry
cloth to do this.
■ At the beginning and end of an extended
period of non-use, charge the battery fully.
■ If a lithium-ion battery is to be stored for an
extended period, the charge level should be
checked regularly. The optimum charge level is
between 50% and 80%. The optimum storage
environment is cool and dry.
WARNING!
■Have the power tool repaired by the
service centre or a qualified electrician and
only using genuine replacement parts. This
will ensure that the safety of the appliance is
maintained.
WARNING!
■Always ensure that the power plug or
the mains cable is replaced only by the
manufacturer of the appliance or by an
approved customer service provider. This
will ensure that the safety of the appliance is
maintained.
NOTE
► Replacement parts not listed (such as the
charger) can be ordered via our service
hotline.

PFBS 12 B2 GB│IE│NI│CY │ 13 ■
Disposal
The packaging is made from environmen-
tally friendly material and can be disposed
of at your local recycling plant.
Do not dispose of power tools in
your normal domestic waste!
European Directive 2012/19/EU requires that
worn-out power tools be collected separately and
recycled in an environmentally compatible manner.
Do not dispose of batteries in your
normal household waste!
NOTE
► The integrated rechargeable battery in this
appliance cannot be removed for disposal.
► The integrated lithium-ion battery may only
be removed by trained personnel. To remove
the battery from the housing, the battery must
be empty and the screws unscrewed from the
housing. The connections on the battery must
individually disconnected and isolated.
Defective or worn-out rechargeable batteries must
be recycled according to Directive 2006/66/EC.
Take the battery pack and/or appliance to a near-
by collection facility.
Please consult your local authorities regarding
suitable disposal of worn-out power tools/battery
packs.
Dispose of the packaging in an
environmentally friendly manner.
Note the labelling on the packaging
and separate the packaging material
components for disposal if necessary.
The packaging material is labelled
with abbreviations (a) and numbers
(b) with the following meanings:
1–7: plastics,
20–22: paper and cardboard,
80–98: composites
Your local community or municipal
authorities can provide information
on how to dispose of the worn-out
product.
Kompernass Handels GmbH
warranty
Dear Customer,
This appliance has a 3-year warranty valid from
the date of purchase. If this product has any faults,
you, the buyer, have certain statutory rights. Your
statutory rights are not restricted in any way by the
warranty described below.
Warranty conditions
The validity period of the warranty starts from the
date of purchase. Please keep your original receipt
in a safe place. This document will be required as
proof of purchase.
If any material or production fault occurs within
three years of the date of purchase of the product,
we will either repair or replace the product for you
at our discretion. This warranty service is dependent
on you presenting the defective appliance and
the proof of purchase (receipt) and a short written
description of the fault and its time of occurrence.
If the defect is covered by the warranty, your product
will either be repaired or replaced by us. The repair
or replacement of a product does not signify the
beginning of a new warranty period.

PFBS 12 B2
■ 14 │ GB│IE│NI│CY
Warranty period and statutory claims for
defects
The warranty period is not prolonged by repairs
effected under the warranty. This also applies to
replaced and repaired components. Any damage
and defects present at the time of purchase must
be reported immediately after unpacking. Repairs
carried out after expiry of the warranty period shall
be subject to a fee.
Scope of the warranty
This appliance has been manufactured in accordance
with strict quality guidelines and inspected meticu-
lously prior to delivery.
The warranty covers material faults or production
faults. The warranty does not extend to product parts
subject to normal wear and tear or fragile parts such
as switches, batteries, baking moulds or parts made
of glass.
The warranty does not apply if the product has been
damaged, improperly used or improperly maintained.
The directions in the operating instructions for the
product regarding proper use of the product are
to be strictly followed. Uses and actions that are
discouraged in the operating instructions or which
are warned against must be avoided.
This product is intended solely for private use and
not for commercial purposes. The warranty shall be
deemed void in cases of misuse or improper handling,
use of force and modifications/repairs which have
not been carried out by one of our authorised
Service centres.
Warranty claim procedure
To ensure quick processing of your case, please
observe the following instructions:
■ Please have the till receipt and the item number
(e.g. IAN 12345) available as proof of purchase.
■ You will find the item number on the type plate,
an engraving on the front page of the instructions
(bottom left), or as a sticker on the rear or
bottom of the appliance.
■ If functional or other defects occur, please
contact the service department listed either by
telephone or by e-mail.
■ You can return a defective product to us free of
charge to the service address that will be provided
to you. Ensure that you enclose the proof of
purchase (till receipt) and information about
what the defect is and when it occurred.
You can download these instructions
along with many other manuals,
product videos and software on
www.lidl-service.com.
Service
Service Great Britain
Tel.: [phone]
E-Mail: [email protected]
Service Ireland
Tel.: [phone]
(0,08 EUR/Min., (peak))
(0,06 EUR/Min., (off peak))
E-Mail: [email protected]
CY Service Cyprus
Tel.: [phone]
E-Mail: [email protected]
IAN 306948
Importer
Please note that the following address is not the
service address. Please use the service address
provided in the operating instructions.
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
DE-44867 BOCHUM
GERMANY
www.kompernass.com

PFBS 12 B2 GB│IE│NI│CY │ 15 ■
Translation of the original Conformity Declaration
We, KOMPERNASS HANDELS GMBH, documents officer: Mr Semi Uguzlu, BURGSTR. 21,
DE - 44867 BOCHUM, Germany, hereby declare that this product complies with the following standards,
normative documents and EC directives:
Machinery Directive
(2006/42/EC)
EMC (Electromagnetic Compatibility)
(2014/30/EU)
RoHS Directive
(2011/65/EU)*
*The manufacturer bears the full responsibility for compliance with this conformity declaration. The object
of the declaration described above complies with the requirements of the Directive 2011/65/EU of the
European Parliament and Council of 8 June 2011 on the limitations of use of certain dangerous substances
in electrical and electronic appliances.
Applied harmonised standards:
EN 60745-1:2009/A11:2010
EN 60745-2-23:2013
EN 55014-1:2006/A2:2011
EN 55014-1:2017
EN 55014-2:2015
EN 60335-1:2012/A11:2014
EN 60335-2-29:2004/A2:2010
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 62233:2008
EN 50581:2012
Type designation of machine: Cordless rotary tool PFBS 12 B2
Year of manufacture: 05-2018
Serial number: IAN 306948
Bochum, 08/05/2018
Semi Uguzlu
- Quality Manager -
We reserve the right to make technical changes in the context of further product development.

PFBS 12 B2
■ 16 │ GB│IE│NI│CY

PFBS 12 B2 GR│CY │ 17 ■
Περιεχόμενα
Εισαγωγή.......................................................18
Προβλεπόμενη χρήση ....................................................... 18
Εξοπλισμός ...............................................................18
Παραδοτέος εξοπλισμός.....................................................18
Τεχνικά χαρακτηριστικά ...................................................... 18
Γενικές υποδείξεις ασφαλείας για ηλεκτρικά εργαλεία...................19
1. Ασφάλεια στο χώρο εργασίας...............................................20
2. Ηλεκτρική ασφάλεια....................................................... 20
3. Ασφάλεια ατόμων ........................................................ 20
4. Χρήση και χειρισμός του ηλεκτρικού εργαλείου .................................21
5. Χρήση και χειρισμός του επαναφορτιζόμενου εργαλείου ..........................21
6. Σέρβις ................................................................. 22
Υποδείξεις ασφαλείας για όλες τις χρήσεις.......................................22
Περισσότερες υποδείξεις ασφαλείας για όλες τις χρήσεις ........................... 24
Επιπρόσθετες υποδείξεις ασφαλείας για λείανση και αποκοπή με λείανση ..............24
Επιπρόσθετες υποδείξεις ασφαλείας για την εργασία με συρματόβουρτσες ............. 25
Υποδείξεις ασφαλείας για φορτιστές............................................ 26
Χειρισμός.......................................................26
Φόρτιση ενσωματωμένου συσσωρευτή........................................... 26
Ανάγνωση κατάστασης συσσωρευτών ...........................................26
Τοποθέτηση/Αλλαγή εργαλείου/λαβίδας σύσφιξης ............................... 27
Ενεργοποίηση και απενεργοποίηση/Ρύθμιση εύρους αριθμού στροφών................27
Υποδείξεις για την επεξεργασία υλικού/Εργαλεία/Εύρος αριθμού στροφών ............ 27
Υποδείξεις και τεχνάσματα.................................................... 29
Συντήρηση και καθαρισμός........................................29
Απόρριψη ......................................................30
Εγγύηση της Kompernass Handels GmbH ............................30
Σέρβις. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Εισαγωγέας .....................................................31
Μετάφραση της Πρωτότυπης Δήλωση συμμόρφωσης ...................32