Parkside PSS 65 C1 Operating and installation instructions

Tool Sharpening Station PSS 65 C1
Tool Sharpening Station
Translation of the original instructions
Συσκευή ακονίσατο
Μετάφραση των αυθεντικών οδηγιών λειτουργίας
IAN 374688 _ 2104
Schärfstation
Originalbetriebsanleitung

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions
of the device.
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες
της συσκευής.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit
allen Funktionen des Gerätes vertraut.
GB /IE / NI /CY Translation of the original instructions Page X5GR /CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 19DE / AT / CH Originalbetriebsanleitung Seite 34

154
7
8
9
12 101113
13
632
15
16
14

14
15
10
12
11
180°

5
GB IE NI CY
Content
Introduction .................................5
Intended use................................ 5
General description...................... 6
Scope of delivery..............................6
Function description...........................6
Summary .........................................6
Technical specications................. 6
Safety Instructions........................7
Symbols and icons ............................7
General Safety Directions for Power
Tools................................................7
Further Safety Instructions...................9
Residual risks..................................10
Assembly................................... 11
Setting up ......................................11
Mount the sharpener .......................11
Operation ..................................11
Switching on and off .......................12
Sharpening drills.............................12
Sharpening picks and chisels............12
Sharpening knives...........................13
Sharpening scissors.........................13
Changing the grinding wheel ...........14
Cleaning and maintenance.........14
Cleaning........................................14
Storage...................................... 14
Waste disposal and
environmental protection ...........15
Replacement parts/accessories... 15
Trouble Shooting........................ 16
Guarantee .................................17
Repair Service............................18
Service-Center............................ 18
Importer .................................... 18
Introduction
Congratulations on the purchase of your
new device. With it, you have chosen a
high quality product.
During production, this equipment has
been checked for quality and subjected to
a nal inspection.
The operating instructions constitute
part of this product. They contain
important information on safety, use and
disposal.
Before using the product, familiarise your-
self with all of the operating and safety
instructions. Use the product only as de-
scribed and for the applications specied.
Keep this manual safely and in the event
that the product is passed on, hand over
all documents to the third party.
Intended use
The sharpening station is suitable for sharp-
ening tools (e.g. drills, knives, scissors,
picks, chisel).
The device is not intended for all other
types of applications (e.g. grinding with
unsuitable grinding tools, grinding with a
coolant solution, grinding hazardous mate-
rials such as asbestos).
The equipment is intended for use in the
eld of DIY. It is not designed for commer-
cial use.
The equipment is designed for use by
adults. Young people over the age of 16
are permitted to use the equipment only
under supervision.
The manufacturer shall not be liable for
damages caused by use other than for the
intended purpose or by incorrect opera-
tion.
UKCA declaration of conformity..50
Translation of the original
EC declaration of conformity ......51
Exploded Drawing .....................55

6
GB IE NI CY
General description
The illustrations can be found on
the front and rear fold-out pages.
Scope of delivery
Unpack the equipment and check that it is
complete. Dispose of the packaging mate-
rial correctly.
• Appliance
• Sharpener for knives and scissors
• Sharpener for drills
• Sharpener for picks and chisels
• Spare grinding wheel
• Instruction Manual
Function description
The sharpening station is suitable for
sharpening tools (e.g. drills, knives, scis-
sors, picks, chisels). The scope of delivery
contains three sharpeners for this purpose,
which, as a guide and safety device, en-
able precise sharpening and grinding.
Refer to the following descriptions for a
functional description of the controls.
Summary
1 Mains plug
2 Sharpener for knives and scissors
3 On/off switch
4 Spacer
5 Magnet holder
6 Tool table
7 Retaining screw for
angular adjustment
8 Protective hood
9 Mounting holes for work bench
assembly
10 Grinding wheel
11 rotatable drill mount
12 Knurled nut for drill-fastening
13 Release lever for sharpener
14 Drill holder
15 Adjusting device
16 Grinding wheel nuts
Technical specications
Tool sharpening station.. PSS 65 C1
Nominal
input voltage .......... 220 - 240 V~, 50 Hz
Power consumption P..... 65 W (S6 20%)*
Power consumption P0..........25 W (S1)**
Measurement idling speed n0... 6700 min-1
Safety class ..................................... II
Protection category..........................IP X0
Weight
(incl. accessories)........... approx. 1.37 kg
Grinding angle range................15° - 50°
Sharpness drill diameter............ 3 -10 mm
Sharpness knife width.............. 6 - 51 mm
Grinding wheel
Outer diameter .................. Ø 49.5 mm
Borehole diameter............ Ø 10.14 mm
Thickness ................................7.9 mm
Abrasive ............................... Diamond
Base body..................................Metal
Working speed................ max. 60 m/s
Rotational speed ....... max. 23100 min-1
Sound pressure level
(LpA)...................60.5 dB(A); KpA= 3 dB
Sound power level
(LWA)................. 73.5 dB(A); KWA= 3 dB
* Operating mode S6 20%: Continuous op-
eration with intermittent load (cycle time
10min). In order not to heat the motor
more than permitted, the motor may only be
operated for 20% of the cycle time with the
stated nominal power and must then continue
running for 80% of the cycle time without a
load.
** Operating mode S1: Continuous operation
with constant load

7
GB IE NI CY
Noise and vibration values have been
determined according to the standards and
regulations mentioned in the declaration of
conformity.
Safety Instructions
Symbols and icons
Symbols on the device:
Warning!
Read the instruction manual.
Wear ear protection.
Risk of electric shock! Disconnect
from the mains before carrying out
maintenance and repair work.
Safety class II (Double insulation)
Do not dispose of electrical equip-
ment in household waste.
Drill diameter
Grinding wheel nut
Grinding angle
Workpiece size
For grinding
knives and scissors
Rotatable drill retainer
Producer
Imported for GB market by:
Lidl Great Britain Ltd.
Lidl House, 14 Kingston Road
Surbiton, KT5 9NU
Symbols in the manual:
Warning symbols with in-
formation on damage and
injury prevention.
Instruction symbols with information
on preventing damage.
Connect the machine to the power
supply.
Pull out the mains plug.
Wear ear protection
Help symbols with information on
improving tool handling.
General Safety Directions for
Power Tools
WARNING! Read all safety
warnings, instructions, il-
lustrations and specications
provided with this power
tool. Failure to follow all instruc-
tions listed below may result in
electric shock, re and/or serious
injury.
Save all warnings and instructions
for future reference.
The term „power tool“ in the warnings
refers to your mains-operated (corded)
power tool or battery-operated (cordless)
power tool).
1) Work area safety
a) Keep work area clean and well
lit. Cluttered or dark areas invite ac-
cidents.

8
GB IE NI CY
able, please use a residual cur-
rent circuitry. The use of a residual
current circuitry reduces the risk of an
electric shock.
3) Personal safety
a) Stay alert, watch what you are
doing and use common sense
when operating a power tool.
Do not use a power tool while
you are tired or under the inu-
ence of drugs, alcohol or medi-
cation. A moment of inattention white
operating power tools may result in
serious personal injury.
b) Use personal protective equip-
ment. Always wear eye protec-
tion. Protective equipment such as dust
mask, non-skid safety shoes, hard hat,
or hearing protection used for appro-
priate conditions will reduce personal
injuries.
c) Prevent unintentional starting.
Ensure the switch is in the off-
position before connecting to
power source and/or battery
pack, picking up or carrying the
tool. Carrying power tools with your
nger on the switch or energising pow-
er tools that have the switch on invites
accidents.
d) Remove any adjusting key or
wrench before turning the pow-
er tool on. A wrench or a key left at-
tached to a rotating part of the power
tool may result in personal injury.
e) Do not overreach. Keep proper
footing and balance at all times.
This enables better control of the power
tool in unexpected situations.
f) Dress properly. Do not wear
loose clothing or jewellery. Keep
your hair, clothing and gloves
b) Do not operate power tools in
explosive atmospheres, such as
in the presence of ammable
Iiquids, gases or dust. Power tools
create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders
away while operating a power
tool. Distractions can cause you to
lose control.
2) Electrical safety
a) Power tool plugs must match
the outlet. Never modify the
plug in any way. Do not use
any adapter plugs with earthed
(grounded) power tools. Unmodi-
ed plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed
or grounded surfaces, such as
pipes, radiators, ranges and re-
frigerators. There is an increased risk
of electric shock if your body is earthed
or grounded.
c) Do not expose power tools to
rain or wet conditions. Water
entering a power tool will increase the
risk of electric shock.
d) Do not abuse the cord. Never
use the cord for carrying, pull-
ing or unplugging the power
tool. Keep cord away from
heat, oil, sharp edges or moving
parts. Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of a
cord suitable for outdoor use reduces
the risk of electric shock.
f) If operation of the power tool in
a damp environment is unavoid-

9
GB IE NI CY
away from moving parts. Loose
clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the
connection of dust extraction
and collection facilities, ensure
these are connected and prop-
erly used. Use of dust collection can
reduce dust-related hazards.
h) Do not let familiarity gained
from frequent use of tools allow
you to become complacent and
ignore tool safety principles. A
careless action can cause severe injury
within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the
switch does not turn it on and
off. Any power tool that cannot be
controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the
power source and/or remove
the battery pack, if detach-
able, from the power tool be-
fore making any adjustments,
changing accessories, or storing
power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the
reach of children and do not al-
low persons unfamiliar with the
power tool or these instructions
to operate the power tool. Power
tools are dangerous in the hands of
untrained users.
e) Maintain power tools and acces-
sories. Check for misalignment
or binding of moving parts,
breakage of parts and any
other condition that may affect
the power tool’s operation. If
damaged, have the power tool
repaired before use. Many acci-
dents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and
clean. Properly maintained cutting
tools with sharp cutting edges are less
Iikely to bind and are easier to control.
g) Use the power tool, accessories
and tool bits etc. in accordance
with these instructions, taking
into account the working condi-
tions and the work to be per-
formed. Use of the power tool for op-
erations different from those intended
could result in a hazardous situation.
h) Keep handles and grasping sur-
faces dry, clean and free from
oil and grease. Slippery handles
and grasping surfaces do not allow for
safe handling and control of the tool in
unexpected situations.
5) Service
a) Have your power tool serviced
by a qualied repair person us-
ing only identical replacement
parts. This will ensure that the safety
of the power tool is maintained.
Further Safety Instructions
• Connect the device only to a power
point with a RCD (Residual Current De-
vice) with a measured residual current
of not more than 30 mA.

10
GB IE NI CY
• Keep the mains cable and extension
cable away from the grinding disk and
saw chain. In the event that it is dam-
aged or severed, immediately discon-
nect the plug from the socket.
Do not touch the cable before it has
been disconnected from the mains.
Risk of electric shock.
• The replacement of the plug or the
cable must be carried out by the manu-
facturer or his/her customer service in
order to avoid any hazards.
• Only switch the device on once it is
safely xed to the worktop.
• For your own safety only use acces-
sories and attachments which were
stated in the operating instructions or
recommended or specied by the tool
manufacturer.
• Only use grinding wheels where the
printed rotational speed is at least as
high as what has been specied on the
name plate of the device.
• Carry out a visual inspection of the
grinding wheel before use. Do not use
any damaged or deformed grinding
wheels. Replace any damaged or worn
grinding wheels.
• Make sure that the sparks produced by
grinding do not present a danger, e.g.
reach people or ignite ammable sub-
stances.
• Never keep the ngers between the
grinding wheel and spark protection
or in close proximity to the protective
hoods. There is a risk of crushing.
• The rotating parts of the device cannot
be covered due to functional reasons.
Therefore, proceed cautiously and hold
the workpiece rmly in order to avoid
slipping which could cause your hands
to come into contact with the grinding
belt or grinding wheel.
• The workpiece gets hot during grind-
ing. Do not touch the machined area,
allow it to cool down. There is a risk
of burning. Do not use coolants or the
like.
• If you are tired or have consumed al-
cohol or tablets, do not work with the
device. Always have a break on time.
• Switch the device off and remove the
mains plug
- to loosen a blocked insertion tool,
- if the connection line is damaged or
entangled,
- in case of unusual sounds.
Residual risks
Even if properly operating and handling
this electric tool, some residual risks will
remain. Due to its construction and build,
this electric tool may present the following
hazards:
a) Lung damage, if suitable respiratory
protection is not worn.
b) Hearing damage, if suitable ear protec-
tion is not worn.
c) Damages to health due to
- touching the area of the grinding tool
which was not covered;
- the ejection of pieces from workpiece
or damaged grinding wheels.
d) Damage to your health caused by
swinging your hands and arms when
operating the appliance for longer pe-
riods of time or if the unit is not held or
maintained properly.
Warning! During operation, this
electric tool generates an electro-
magnetic eld which, under certain
circumstances, may impair the
functionality of active or passive
medical implants. To reduce the risk
of serious or lethal injuries, we rec-

11
GB IE NI CY
ommend that persons with medical
implants consult their doctor and
the manufacturer of their medical
implant before operating the ma-
chine.
Assembly
Caution! Risk of injury!
- Ensure that you have sufcient
space in which to work, and that
you do not endanger other people.
- All covers and protective devices
must be assembled properly be-
fore commissioning.
- Disconnect the mains plug before
changing the setting on the de-
vice.
Setting up
Place the sharpening station on rm sur-
face and fasten the device. Ideally, bolt the
drill to the surface. Use the mounting holes
for the work bench assembly ( 9) in the
baseplate for this.
The screws and nuts required for as-
sembly are not part of the scope of
delivery.
Mount the sharpener
1. Select one of the three sharpeners.
2. In order to remove a sharpener from
the working position, you must press
down the release lever for the sharp-
ener ( 13).
3. Remove the sharpener from the guide
rails, upwards.
4. In the storage positions, the sharpeners
are not xed to the right and left side
and can be easily removed from the
guide rails.
5. In order to fasten the selected sharpen-
er in the working position, from above
push this into the guide rails. Press
the sharpener down until it snaps into
place.
The sharpeners also present
a safety device. Never use
this device without a sharp-
ener. Risk of injury!
Operation
Caution! Risk of injury!
- Always disconnect the plug from
the mains socket before working.
- Use only grinding disks and ac-
cessories recommended by the
manufacturer. The use of other
insertion tools and other accesso-
ries may cause risk of injury.
- Never operate the device without
the visual protection disk.
- Switch on the equipment only
when it is safely installed on the
work surface.
Despite spark protection,
always wear safety goggles
while working in order to
avoid eye injuries.
We recommend wearing ear pro-
tection to prevent damage to hear-
ing.
Keep your hands away
from the grinding wheel and
grinding belt when the device
is in operation. Injury haz-
ard.

12
GB IE NI CY
Switching on and off
Ensure that the mains voltage
matches the specications on the
rating plate.
Connect the equipment to the
mains.
1. To switch on, press the “I” On switch
and the device starts up (see 3).
2. To switch off, press the “0” off switch
and the device switches off (see 3).
After switching on the device, wait until the
device has reached its max. speed. Only
then must you start with the grinding.
The disk will continue to
run after the equipment is
switched off. There is a risk
of injury.
Test run:
Before starting work and after each
change of grinding disk, carry out a test
run of at least 60 seconds with no load.
Switch off the equipment immediately if the
disk runs lumpy, substantial vibrations oc-
cur, or abnormal noises are generated.
Sharpening drills
Drills with a diameter of 3-10 mm can be
sharpened.
1. Mount the selected sharpener (see
Mounting sharpener).
2. Remove the drill holder (14) from the
sharpener.
3. Insert the drill into the drill holder (14).
Do not attach the drill.
4. Insert the drill holder (14) upwards
into the adjusting device (15) using the
knurled nut for drill-fastening (12).
5. Push the drill to the front into the V-nut
up to the metal stop. The cutting edges
of the drill must t closely to the metal
surfaces.
6. Using the knurled nut fasten the drill for
drill-fastening (12).
7. Remove the drill holder (14) and insert
this into the rotatable drill mount (11)
from below using the knurled nut for
drill-fastening (12).
8. Check the alignment of the drill. The
cutting edges of the drill must be touch-
ing the grinding wheel (10).
9. Switch the device on and grind the drill
by moving the rotatable drill mount
(11) to and fro in the direction of the
arrow.
10.Switch the device off and wait for the
grinding wheel (10) to stop.
11.Remove the drill holder (14) and insert
it into the rotatable drill mount (11) by
rotating in by 180°. Using the same
adjustment, you can grind the opposite
cutting edge of the drill.
12.Switch the device off and grind the
drill.
13.Switch the device off and wait for the
grinding wheel (10) to stop.
Sharpening picks and
chisels
1. Mount the selected sharpener (see
Mounting sharpener).
2. Place the blade on the tool table (6) so
that it lies against the spacer (4). The
magnetic holder (5) keeps the blade in
position.

13
GB IE NI CY
3. Release the retaining screw for the an-
gular adjustment (7) and turn the tool
table (6) into position. Select the angle
according to the existing bevel angle
(angle of the bevelled edge).
4. Tighten the retaining screw for angular
adjustment (7) again.
5. Switch the device on and move the tool
table (6) equally back and forth along
the grinding wheel (10).
6. Always use light pressure while sharp-
ening and slowly push the blade to-
wards the grinding wheel (10).
7. Repeat the sharpening process until all
irregularities have been removed.
8. Switch the device off and wait for the
grinding wheel (10) to stop.
To sharpen a chisel, turn the chisel
over and repeat the process from
Point 5.
Sharpening knives
The device is not suitable for grind-
ing serrated knives.
1. Mount the selected sharpener (see
Mounting sharpener).
2. Turn the machine on.
3. Insert the blade of the knife right into
the grinding slot.
4. Using light pressing guide the blade
along the grinding wheel (10) and
evenly and slowly pull the knife to-
wards you.
5. Turn the knife and insert the knife blade
into the opposite grinding slot.
6. Repeat this grinding process for this
side of the blade as well.
7. Execute the alternating grinding pro-
cess until the cutting edge is burr-free
and sharp.
8. Switch the device off and wait for the
grinding wheel (10) to stop.
Sharpening scissors
The device is not suitable for grind-
ing serrated scissors. The device
is not suitable for grinding pinking
shears.
1. Mount the selected sharpener (2)(see
Mounting sharpener).
2. Completely open the scissors.
3. Turn the machine on.
4. Insert one of the scissor blades into the
grinding slot.
5. Using light pressure guide the blade
from the screw up to the tip along the
grinding wheel (10).
6. Remove the scissors from the sharpen-
ing station and turn the scissors to
sharpen the other blade.
7. Insert the other scissor blade into the
grinding slot.
8. Using light pressure guide the blade
from the screw up to the tip along the
grinding wheel (10).
9. Execute the alternating grinding pro-
cess until the cutting edges are burr-free
and sharp.
10.Switch the device off and wait for the
grinding wheel (10) to stop.

14
GB IE NI CY
Changing the grinding wheel
Information on replacement:
• Never operate the device without
protective equipment.
• Ensure that the grinding wheel
dimensions match those of the
device.
• Never use separate bushings or
adapters in order to make grind-
ing wheels whose hole is too
large t the device.
• Do not use any saw blades.
• Always reassemble the device
completely after replacing the
grinding wheel.
Switch the device off and remove
the mains plug.
Allow the device to cool down.
When the grinding disc nut (16) is
being tightened or loosened, the
grinding disc (10) must be held rm
by hand or the axle held rmly in
place with a pair of pliers.
1. Release the grinding wheel
nut (16) in the clockwise di-
rection (left-handed thread).
2. Remove the grinding wheel (10).
3. Set up a new grinding wheel (10).
Screw the grinding wheel nut (16) in
the anti- clockwise direction (left-hand-
ed thread).
4. Test run: Before starting work and af-
ter each change of grinding disk, carry
out a test run of at least 60 seconds
with no load. Switch off the equipment
immediately if the disk runs lumpy, sub-
stantial vibrations occur, or abnormal
noises are generated.
Cleaning and
maintenance
Disconnect the plug before adjust-
ment, maintenance or repair.
Have any work not described
in these instructions carried
out by a specialist workshop.
Use only original compo-
nents. Allow the equipment
to cool before carrying out
any maintenance and clean-
ing work. There is a risk of
burns.
Before each use, check the equipment
for obvious defects such as loose, worn
or damaged components and check that
screws or other parts are sitting correctly.
In particular, check the grinding disk
(10). Replace damaged parts.
Cleaning
Do not use cleaning agents or sol-
vents. Chemical substances may at-
tack plastic parts of the equipment.
Never clean the equipment under
running water.
• Clean the equipment thoroughly after
each use.
• Clean the surface of the device with a
soft brush or cloth.
Storage
• Store the appliance in a dry place well
out of reach of children.
• Grinding disks must be stored dry and
upright and are not to be stacked.

15
GB IE NI CY
Waste disposal and en-
vironmental protection
Be environmentally friendly. Return the
tool, accessories and packaging to a recy-
cling centre when you have nished with
them.
Machines are not to be place with
domestic waste.
• Hand over the device at an utilization
location. The plastic and metal parts
employed can be separated out into
pure materials and recycling can be
implemented. Ask your Service Center
about this.
• Defective units returned to us will be
disposed of for free.
Replacement parts/accessories
Spare parts and accessories can be obtained at
www.grizzlytools.shop
If you have issues ordering, please use the contact form.
If you have any other questions, contact the ”Service-Center” (see page 18).
Position Position Description Order
Instruction Exploded number
manual drawing
10 19+21 Grinding wheel with Grinding wheel nuts 91103590
2 25 Sharpener for knives and scissors 91103591
12 Sharpener for drills 91103592
10 Sharpener for picks and chisels 91103593

16
GB IE NI CY
Trouble Shooting
Always disconnect the plug from the mains socket before working.
Danger of electric shock.
Problem Possible Cause Error correction
Device doesn‘t start
Mains voltage missing
Main circuit breaker is tripped
Check the socket, mains cable,
line, mains plug, repairs to be
carried out by qualied electri-
cian if necessary, check main
circuit breaker.
On/off switch ( 3) may be
defective Repair by Customer Care
Engine faulty
Grinding tools do
not move although
the engine is run-
ning
Grinding wheel nut ( 16)
loose
Tighten grinding wheel nut (see
„Changing the grinding wheel“)
Workpiece, remaining work-
pieces or remaining grinding
tools block drive Remove blockages
Engine is slower
and stops Device is overloaded through workpiece
Reduce pressure on grinding tool
Workpiece unsuitable
Grinding wheel
does not rotate
smoothly, abnor-
mal noises can be
heard
Grinding wheel nut ( 16)
loose
Tighten grinding wheel nut (see
„Changing the grinding wheel“)
Grinding wheel ( 10) faulty Change grinding wheel

17
GB IE NI CY
Guarantee
Dear Customer,
This equipment is provided with a 3-year
guarantee from the date of purchase.
In case of defects, you have statutory rights
against the seller of the product. These
statutory rights are not restricted by our
guarantee presented below.
Terms of Guarantee
The term of the guarantee begins on the
date of purchase. Please retain the original
receipt. This document is required as proof
of purchase.
If a material or manufacturing defect
occurs within three years of the date of
purchase of this product, we will repair or
replace – at our choice – the product for
you free of charge. This guarantee requires
the defective equipment and proof of pur-
chase to be presented within the three-year
period with a brief written description of
what constitutes the defect and when it oc-
curred.
If the defect is covered by our guarantee,
you will receive either the repaired product
or a new product. No new guarantee pe-
riod begins on repair or replacement of the
product.
Guarantee Period and Statutory
Claims for Defects
The guarantee period is not extended by
the guarantee service. This also applies for
replaced or repaired parts. Any damages
and defects already present at the time of
purchase must be reported immediately af-
ter unpacking. Repairs arising after expiry
of the guarantee period are chargeable.
Guarantee Cover
The equipment has been carefully pro-
duced in accordance with strict quality
guidelines and conscientiously checked
prior to delivery.
The guarantee applies for all material and
manufacturing defects. This guarantee
does not extend to cover product parts that
are subject to normal wear and may there-
fore be considered as wearing parts (e.g.
grinding wheels) or to cover damage to
breakable parts (e.g. switches).
This guarantee shall be invalid if the prod-
uct has been damaged, used incorrectly or
not maintained. Precise adherence to all of
the instructions specied in the operating
manual is required for proper use of the
product. Intended uses and actions against
which the operating manual advises or
warns must be categorically avoided.
The product is designed only for private
and not commercial use. The guarantee
will be invalidated in case of misuse or
improper handling, use of force, or inter-
ventions not undertaken by our authorised
service branch.
Processing in Case of Guarantee
To ensure quick handling of you issue,
please follow the following directions:
• Please have the receipt and item num-
ber (IAN374688_2104) ready as
proof of purchase for all enquiries.
• Please nd the item number on the rat-
ing plate.
• Should functional errors or other de-
fects occur, please initially contact the
service department specied below by
telephone or by e-mail. You will then
receive further information on the pro-
cessing of your complaint.

18
GB IE NI CY
• After consultation with our customer
service, a product recorded as defec-
tive can be sent postage paid to the
service address communicated to you,
with the proof of purchase (receipt) and
specication of what constitutes the
defect and when it occurred. In order
to avoid acceptance problems and
additional costs, please be sure to use
only the address communicated to you.
Ensure that the consignment is not sent
carriage forward or by bulky goods, ex-
press or other special freight. Please send
the equipment inc. all accessories sup-
plied at the time of purchase and ensure
adequate, safe transport packaging.
Repair Service
For a charge, repairs not covered by the
guarantee can be carried out by our ser-
vice branch, which will be happy to issue
a cost estimate for you.
We can handle only equipment that has
been sent with adequate packaging and
postage.
Attention: Please send your equipment to
our service branch in clean condition and
with an indication of the defect.
Equipment sent carriage forward or by
bulky goods, express or other special
freight will not be accepted.
We will dispose of your defective devices
free of charge when you send them to us.
Service-Center
GB Service Great Britain
Tel.: [phone]
E-Mail: [email protected]
IAN 374688_2104
IE Service Ireland
NI
Service Northern Ireland
Tel.: [phone]
(0,08 EUR/Min., (peak))
(0,06 EUR/Min., (off peak))
E-Mail: [email protected]
IAN 374688_2104
CY Service Cyprus
Tel.: [phone]
E-Mail: [email protected]
IAN 374688_2104
Importer
Please note that the following address is
not a service address. Please initially con-
tact the service centre specied above.
Grizzly Tools GmbH & Co. KG
Stockstädter Straße 20
63762 Großostheim
GERMANY
www.grizzlytools.de

19
GR CY
Περιεχόμενα
Εισαγωγή .......................................19
Σκοπός χρήσης .............................. 19
Γενική περιγραφή .......................... 20
Παραδοτέα υλικά ...................................... 20
Περιγραφή λειτουργίας ............................ 20
Σύνοψη ...................................................... 20
Τεχνικά στοιχεία............................. 20
Υποδείξεις ασφάλειας.....................21
Σύμβολα και εικονοσύμβολα .................... 21
Γενικές υποδείξεις ασφαλείας για
ηλεκτρικά εργαλεία.................................... 21
Περισσότερες υποδείξεις ασφαλείας...... 24
Υπολειπόμενου κινδύνου .......................... 25
Συναρμολόγηση............................. 25
Τοποθέτηση ............................................... 26
Συναρμολόγηση διατάξεων
ακονίσματος............................................... 26
Χειρισμός ......................................26
Ενεργοποίηση και απενεργοποίηση......... 26
Ακόνισμα τρυπανιών ................................. 27
Ακόνισμα σμιλών και σκαρπέλων............. 28
Ακόνισμα μαχαιριών.................................. 28
Ακόνισμα ψαλιδιών ................................... 28
Αλλαγή δίσκου λείανσης ........................... 29
Καθαρισμός και συντήρηση ........... 29
Καθαρισμός............................................... 30
Αποθήκευση .................................. 30
Απόσυρση/προστασία του
περιβάλλοντος............................... 30
Ανταλλακτικά/Αξεσουάρ................ 30
Ανίχνευση βλαβών ........................ 31
Εγγύηση......................................... 32
Σέρβις επισκευής............................ 33
Service-Center............................... 33
Εισαγωγέας....................................33
Εισαγωγή
Συγχαρητήρια για την αγορά της νέας συ-
σκευής σας. Προτιμήσατε να αγοράσετε ένα
προϊόν ανώτερης ποιότητας. Η ποιότητα αυτής
της συσκευής ελέγχθηκε κατά τη διάρκεια της
παραγωγής, αλλά και σε τελικό έλεγχο. Με τον
τρόπο αυτό εξασφαλίστηκε η λειτουργικότητα
της συσκευής σας.
Οι οδηγίες χρήσης αποτελούν αναπό-
σπαστο τμήμα αυτού του προϊόντος.
Περιέχουν σημαντικές υποδείξεις για
την ασφάλεια, τη χρήση και διάθεση
της συσκευής. Πριν τη χρήση του
προϊόντος να εξοικειωθείτε με όλες τις
οδηγίες χειρισμούς και τις υποδείξεις
ασφαλείας. Να χρησιμοποιείτε το
προϊόν μόνο όπως περιγράφεται και
μόνο για τον αναφερόμενο σκοπό.
Να φυλάξετε καλά τις οδηγίες και να
τις παραδώσετε σε τρίτους μαζί με το
προϊόν.
Σκοπός χρήσης
Η συσκευή ακονίσματος ενδείκνυται για το
ακόνισμα εργαλείων (π.χ. τρυπάνια, μαχαίρια,
ψαλίδια, σμίλες, σκαρπέλα).
Η συσκευή δεν προβλέπεται για όλα τα άλλα
είδη χρήσης (π.χ. λείανση μη ακατάλληλα
εργαλεία λείανσης, λείανση με ψυκτικό υγρό,
λείανση υλικών επιβλαβών για την υγεία όπως
αμίαντος).
Το μηχάνημα προορίζεται για χρήση στον το-
μέα οικιακών κατασκευών. Δε σχεδιάστηκε για
τη συνεχή επαγγελματική χρήση.
Το μηχάνημα προορίζεται για τη χρήση από
ενήλικες. Νέοι άνω των 16 ετών επιτρέπεται
να χρησιμοποιούν το μηχάνημα μόνο υπό
επιτήρηση.
Ο κατασκευαστής δεν ευθύνεται για βλάβες,
που προκαλούνται από τη μη προβλεπόμενη
χρήση ή τον εσφαλμένο χειρισμό.
Μετάφραση της πρωτότυπης
Δήλωσης συμμόρφωσης CE ............52
Επί μέρoυς σχεδιαγράμματα ...........55

20
GR CY
Γενική περιγραφή
Θα βρείτε τις απεικονίσεις στην
μπροστινή και πίσω αναδιπλωνό-
μενη σελίδα.
Παραδοτέα υλικά
Αποσυσκευάστε το μηχάνημα και ελέγξτε, εάν
είναι πλήρες. Διαθέστε τα υλικά συσκευασίας
σύμφωνα με τους κανονισμούς.
• Συσκευή
• Διάταξη ακονίσματος για
μαχαίρια και ψαλίδια
• Διάταξη ακονίσματος για τρυπάνια
• Διάταξη ακονίσματος για σμίλες και σκαρ-
πέλα
• Εφεδρικός δίσκος λείανσης
• Οδηγιών χρήσης
Περιγραφή λειτουργίας
Η συσκευή ακονίσματος ενδείκνυται για το
ακόνισμα εργαλείων (π.χ. τρυπάνια, μαχαίρια,
ψαλίδια, σμίλες, σκαρπέλα). Για αυτό περι-
έχονται στο σύνολο αποστολής τρεις διαφο-
ρετικές διατάξεις ακονίσματος, οι οποίες ως
οδηγός και διάταξη ασφαλείας διευκολύνουν
τρόχισμα και λείανση ακριβείας.
Μπορείτε να βρείτε τη λειτουργία των εξαρτη-
μάτων χειρισμού στις κατωτέρω περιγραφές.
Σύνοψη
1 Ρευματολήπτης
2 Διάταξη ακονίσματος για μαχαίρια
και ψαλίδια
3 Διακόπτης ενεργο-/απενεργοποίη-
σης
4 Αποστάτης
5 Μαγνητική συγκράτηση
6 Απόθεση εργαλείου
7 Κοχλίας ασφάλισης για
ρύθμιση γωνίας
8 Προστατευτικό κάλυμμα
9 Οπές συναρμολόγησης για συναρ-
μολόγηση πάγκου εργασίας
10 Δίσκος λείανσης
11 Περιστρεφόμενη υποδοχή διάτρη-
σης
12 Περικόχλιο με ραβδώσεις για την
στερέωση τρυπανιών
13 Μοχλός απασφάλισης για
διατάξεις ακονίσματος
14 Συγκράτηση τρυπανιών
15 Διάταξη ρύθμισης
16 Παξιμάδι δίσκων λείανσης
Τεχνικά στοιχεία
ΣΥΣΚΕΥΉ ΑΚΟΝΊΣΜΑΤΟΣ .. PSS 65 C1
Ονομαστική
τάση εισόδου................. 220 - 240 V~, 50 Hz
Κατανάλωση ......................... 65 W (S6 20%)*
Κατανάλωση ................................25 W (S1)**
Ταχύτητα λειτουργίας
εν κενώ n0........................................ 6700 min-1
Κατηγορία προστασίας............................... II
Τύπος προστασίας..................................... IP X0
Βάρος
(συμπεριλ. εξαρτημάτων)..........περίπ. 1,37 kg
Τομέας γωνίας λείανσης....................15° - 50°
Απόδοση ακονίσματος, διάμετρος
διάτρησης ...........................................3 -10 mm
Απόδοση ακονίσματος, πλάτος
μαχαιριού...........................................6 - 51 mm
Δίσκος λείανσης
Εξωτερική διάμετρος ................. Ø 49,5 mm
Διάμετρος διάτρησης...............Ø 10,14 mm
Πάχος................................................. 7,9 mm
Λειαντικό μέσο..................................Διαμάντι
Κυρίως σώμα................................... Μέταλλο
Ταχύτητα εργασίας .....................μέγ. 60 m/s
Αριθμός στροφών............. μέγ. 23100 min-1
Στάθμη ηχητικής πίεσης
(LpA)............................60,5 dB(A); KpA= 3 dB