Parrot CK3100 LCD User manual

308
This document is a tool to assist with the installation of a Parrot product and is supplied purely for information. Any installation performed in
compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible
for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without
the authorisation of Parrot SA. Pictures for information only.
308
Installation manual:
Parrot MKi + Parrot
CK3100 range
The brand name PEUGEOT 308 and the PEUGEOT logo are the property of AUTOMOBILES PEUGEOT
This document is only valid for the vehicle model 308® year 2007 to 2011, excluding all other models in the same range and excluding later
modifications made to the vehicle by the manufacturer.
The Parrot brand name and logos are the exclusive property of Parrot SA.

308
This document is a tool to assist with the installation of a Parrot product and is supplied purely for information. Any installation performed in
compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible
for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without
the authorisation of Parrot SA. Pictures for information only.
Accessories required
Disassembly 20min
Mounting kit 30min
Refitting 20min
Testing 15min
Total 1h25min
YES +APC
NO ISO
YES UNIKA
FRONT LOUDSPEAKER TEL mode
ALL MUSIC mode
Fitting time (estimated) / Main features
Tools
- TORX screwdriver
- Multimeter or Test lamp
- Wire tie
- Electrical tape
- Round file (or a knife)
"Please contact your wholesaler to purchase
accessories. List of wholesalers available at
www.certified.parrot.com." »
Kram ref. Dealer ref.
CK range 86 165 9706AP
MKi range 84744 9706AT
Photos for illustration purposes
CK range MKi range
To get the most out of your hands-free kit, we recommend that you update your software regularly. The
procedure for doing this can be found at http://www.parrot.com/usa/support/downloads
Updating
Plastic trim removal tools
FACOM / BOJO
FACOM Sleeve
DX-25 (n°4 spanners)

308
This document is a tool to assist with the installation of a Parrot product and is supplied purely for information. Any installation performed in
compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible
for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without
the authorisation of Parrot SA. Pictures for information only.
Disassembly

308
This document is a tool to assist with the installation of a Parrot product and is supplied purely for information. Any installation performed in
compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible
for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without
the authorisation of Parrot SA. Pictures for information only.
Disassembly 1 / 2
Open the ashtray and remove it
pressing on the tongue Remove screws 1 and 2
Using the plastic trim tools, unclip
the air conditioning cover
Using the plastic trim tools,
unclip the storage compartment
Insert the removal tools into the
slots on each side of the radio
Unclip, pull and remove the radio
taking care to properly unplug
the connector and the antenna
1
3
2
4
5 6
1 2

308
This document is a tool to assist with the installation of a Parrot product and is supplied purely for information. Any installation performed in
compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible
for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without
the authorisation of Parrot SA. Pictures for information only.
Disassembly 2 / 2
Using the plastic trim tools, unclip
the button cover
(WARNING)
Using the plastic trim tools, unclip the
cover located on the left side of the
dashboard
Release the fuse-box cover and the
cover under the steering wheel
Remove the door seal on the
driver’s side
Using the plastic trim tools,
release the headliner (but
without disconnecting)
7
9
8
10
11

308
This document is a tool to assist with the installation of a Parrot product and is supplied purely for information. Any installation performed in
compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible
for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without
the authorisation of Parrot SA. Pictures for information only.
Microphone passage
Replacing the headliner, glue the
bracket supplied to the carpet, after
degreasing, sliding it underneath
Using a guide, feed the cable from
inside the headliner towards the
windscreen
Using the plastic trim tools, run the
cable under the head liner and down
the windscreen post on the driver’s side
Run the cable replacing the seal
on the driver’s door
1
3
2
4
5 6
Pass the cable into the
dashboard on the left side
Run it, attaching with wire ties, under
the dashboard to the radio

308
This document is a tool to assist with the installation of a Parrot product and is supplied purely for information. Any installation performed in
compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible
for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without
the authorisation of Parrot SA. Pictures for information only.
Feeding the accessory cable
Pass a guide from the glove box
towards the radio housing
Pass the cable through the hole at
the bottom inside the glove box
Bring it out leaving sufficient
length
Mount the supplied cover on the
cable
1 2
3 4

308
This document is a tool to assist with the installation of a Parrot product and is supplied purely for information. Any installation performed in
compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible
for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without
the authorisation of Parrot SA. Pictures for information only.
Fitting the hands-free system 1 / 2
Connect the adaptor (86165/9706AP for the CK
or 84744/9704AT for the Mki) to the original
connector and connect all of the wires to the
blue box as shown in the diagram below. Test
before reinstalling then slide the assembly into
the housing of the storage compartment
1
ISO
adapter

308
This document is a tool to assist with the installation of a Parrot product and is supplied purely for information. Any installation performed in
compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible
for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without
the authorisation of Parrot SA. Pictures for information only.
Fitting the hands-free system 2 / 2
Glue the supplied mounting
between the air vents (after
degreasing the surface)
With a file or knife, make a notch
just below
Glue the screen support and pass the
cable through the notch. Remount the
buttons (ATTENTION do not cut the
cable)
Pass the cable through the top of
the radio frame
Place the screen and bring out the cable
through the storage compartment
housing
2
4
3
12
5
6
!

308
This document is a tool to assist with the installation of a Parrot product and is supplied purely for information. Any installation performed in
compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible
for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without
the authorisation of Parrot SA. Pictures for information only.
Testing
Before refitting the system, switch the kit on using the
ignition (or by starting the car). By pushing the central knob
of the remote control, check:
1 - that the menu is displayed on the screen (language or
iPod etc)
2 - that the radio system is muted when the kit is in use (click
in the blue box)
3 - that the sound through all speakers is properly muted
4 - that there is sound through the front speakers for spoken
menus
5 - then turn off the ignition, verify that the kit turns off and
that the message “goodbye” is displayed on the screen
(otherwise reverse the fuses on the kit power supply
harness)
6 - pair a telephone with the kit and make a call (check that
both the microphone and the kit are working)