Patriot Lighting OD38996RBZ User manual

Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-887-6326
Monday – Friday 9:00 a.m. – 5:00 p.m. CST
Sku Number: 356-8298
OUTDOOR PENDANT LIGHT
Model Number: OD38996RBZ
Page 1 of 4
191106
HARDWARE CONTENTS Note: Hardware not shown actual size.
PACKAGE CONTENTS
A
B
C
D
E
Mounting Screw
X2
Chain
X1
Loop Lock
X2
Mounting Strap Unit
X1
Wire Connector
X3
Canopy
X1
AA BB CC
DD EE FF
Clip
X3
GG

Page 2 of 4
191106
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with
package contents list and diagram on previous page. If any part is missing or damaged, do not attempt to assemble,
install or operate the product. Contact customer service for replacement parts.
Tools Required for Assembly (not included): Screwdriver, Phillips Screwdriver, Pliers, Electrical Tape, Wire Cutters,
Safety Glasses, Ladder, Wire Stripper.
ASSEMBLY INSTRUCTIONS
PREPARATION
Turn off the power at fuse or circuit box.
WARNING
●Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or
switching off circuit breaker).
●Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact
any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury
or death from electric shock.
CAUTION
●All electrical connections must be in agreement with local codes, ordinances or the national electric code (NEC).
Contact your municipal building department to learn about your local codes, permits and/or inspections.
●Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC. Consult a qualified electrician
before installation.
●Do not connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use
a fixture in a two-wire system that is not grounded. If you are not sure your lighting system has a grounding means,
do not attempt to install this fixture. Contact a qualified, licensed electrician for information with regards to proper
grounding methods as required by the local electrical code in your area.
●If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type and
electrical rating required.
1. Remove the collar from the
mounting strap unit (AA).
Attach the mounting strap
unit (AA) to outlet box using
two mounting screws (BB).
2. Take the glass shade (C) out
from the frame (B) carefully,
then discard the bubble bags
and foams.
AA
BB
1
1
Collar
2
C
B
3. Unscrew the set screws
from the frame (B). Put the
glass shade (C) into the
frame (B) carefully, then
secure it with the clips (GG)
and set screws.
3
GG
C
B
Set Screw

Page 3 of 4
191106
ASSEMBLY INSTRUCTIONS (continued)
4. Connect the chain (FF):
Determine length of chain (FF)
needed to achieve desired
fixture height.
(To remove excess chain
section, use plier to bend link
open.)
Weave the fixture wires through
the chain (FF) , collar and
canopy (DD).
Connect one chain (FF) to the
loop and the top loop on the
mounting strap unit (AA) using
the two loop locks (EE).
Thread the fixture wire and
fixture ground wire through the
threaded pipe on the mounting
strap unit (AA).
6. Attach the canopy (DD) to the
mounting strap unit (AA) by
inserting the top loop into the hole
of canopy (DD), then secure with
the collar.
6
DD
AA
Top Loop Collar
DD
AA
CC
5Green Grounding Screw
7. Install bulbs (not included).
See relamping label at
socket area or packaging for
maximum wattage allowed .
Turn on the power at fuse or circuit box.
5. Pull out the source wires from
the outlet box. Make wire
connections using wire
connectors (CC) as follows:
Connect the smooth wire
(marked) from the fixture to
the black wire (hot) from the
power source.
Connect the ribbed wire
(unmarked) from the fixture
to the white wire (neutral) from the power source.
Attach the fixture grounding wire to the mounting
strap unit (AA) with the green grounding screw.
Then, depending on local code connect it to the
house grounding wire with the wire connector (CC).
Carefully put the wires back into the outlet box.
4
DD
EE
FF
EE
A
Top Loop
Collar
Threaded Pipe
AA
Loop
7
Candle
Cover
Max.60W Type B
Bulb (not included)
8. Unscrew the bottom finial (E) from
the bottom assembly unit, then
secure the threaded pipe into the
coupling by using the hex nut.
Attach the frame (B) to the dome
(A) and attach the cap (D) to the
frame (B) by aligning and
inserting the threaded pipe into
the open hole on the cap (D), then
secure it with the bottom finial (E).
Hex Nut
Threaded
Pipe
D
E
Coupling
B
A
8
E
Bottom Assembly Unit

Page 4 of 4
191106
●Toclean, turn off and wipe with a damp, non-abrasive cloth.
1) Thelight does not come on at all:
a) Make sure the wall switch and circuit breaker are on.
b) Make sure the wiring is correct.
2) Fuse blows or circuit trips when lightis turned on.
Check for crossed wires, ensure wiring is correct.
If unable to fix any of the above issues, please consult a certified electrician.
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-887-6326
Monday – Friday 9:00 a.m. – 5:00 p.m. CST
CARE AND MAINTENANCE
TROUBLESHOOTING
FIVE-YEAR LIMITED WARRANTY: If, during normal use, this PATRIOT LIGHTING lighting fixture breaks or fails
due to a defect in material workmanship within five (5) years from the date of original purchase, simply bring this
lighting fixture with the original sales receipt back to your nearest MENARDS retail store. At its discretion, PATRIOT
LIGHTING agrees to have the product or any defective part(s) repaired or replaced with the same or similar PATRIOT
LIGHTING product or part free of charge, within the stated warranty period, when returned by the original purchaser
with original sales receipt. This warranty; (1) excludes expendable parts including but not limited to light bulbs; (2) does
not cover damage that has resulted from abuse or misuse; and (3) does not cover any losses, labor, injuries to
persons/property or costs. This warranty does give you specific legal rights and you may have other rights, which vary
from state to state.
R
R
R
R
The following parts are available for reorder if damaged or missing. Call our toll free at 1-800-887-6326.
Spare Parts List:
Assembly Kit
X-HCB03RBZ (1 SET)
Bottom Assembly Unit
X-HCB04RBZ (1 SET)
Glass Shade
938991
X1
Mounting Screw
X2
Chain
X1
Loop Lock
X2
Mounting Strap Unit
X1
Wire Connector
X3
Canopy
X1
AA BB CC
DD EE FF
Clip
X3
GG
Bottom Assembly Unit
X1