PB TEEN Sleep & Study Loft Bed - Bookcase User manual

Date – 02-July-2012 www.pbteen.com Page 1/3
Sleep & Study Loft Bed – Bookcase
PRE-ASSEM LY:
• For your safety and ease, assembly by two adults is recommended.
• Please read all instructions before beginning assembly. The illustrations provided allow for easier assembly when
used in conjunction with the assembly instructions.
• Remove all parts and hardware from box and lay out on a carpeted or scratch-free work surface. The shipping
box provides and ideal work surface. Do not dispose of any contents until assembly is completed to avoid
accidentally discarding small parts or hardware.
• Use the parts and hardware lists to identify and separate each of the pieces included prior to starting assembly.
• Note: DO not fully tighten the bolts until all parts are in place. Failure to follow these instructions may cause the
bolts to misalign during assembly.
• Do not use power drill as it may cause cracking.
Assembly Instructions 1 of 4

Date – 02-July-2012 www.pbteen.com Page 2/3
HARD ARE LIST
(D7) Allen Key – 1x
(D8) Long olt 1/4” x 51mm – 4x
(D9) Short olt 1/4“x28mm –20x
(D10) Spring Washer – 24x
(D11) Flat Washer – 24x
ASSEM LY INSTRUCTIONS:
1. Slide a Spring Washer (D10) and a Flat Washer (D11) onto each Long/Short olts (D8 & D9).
2. Attach Support Rail (D6) to bottom of the Center Shelf (D2). Insert (4) Long olts (D) with washers from
Support Rail (D6) into bottom of the Center Shelf (D2) by using Allen Key (D7). Note: Wooden cleat on the
Support Rail (D6) is close to surface of Center Shelf (D2) after assembly.
D6.
D2.
D7.
D10.
D11.
D8.
D1.
D1.
D2.
D1.
D6.
D3.
PARTS LIST
D1). Shelf – 3pcs
D2). Center Shelf – 1pc
D3). ottom Shelf – 1pc
TOOLS REQUIRED:
Philips Screwdriver
(Not included)
D4). Side Panel – 1pc
D5). Cork Panel – 1pc
D6). Support Rail
–
1pc
D8
4x

Date – 02-July-2012 www.pbteen.com Page 3/3
3. Place Side Panel (D4) on a soft, scratch-free surface with bottom wooden blocks facing up. Attach (3) Shelf
(D1), Center Shelf (D2) and ottom Shelf (D3) to Side Panel (D4) in sequence as shown below. Insert (2)
Shorts olts (D9) with washers from wooden cleat of each shelf into Side Panel (D4). Note: Wide apron of
Center Shelf (D2) and apron of ottom Shelf (D3) face the edge without cut-out on bottom.
4. Place Cork Panel (D5) onto the assembled piece. Secure each shelf to Cork Panel (D5) by inserting (2) Short
olts (D9) with washers. Note: Cut-Out corner of the Side Panel and Corkboard Panel face each other.
Place the assembled bookcase in upright position. Check alignments and tighten all connecting bolts.
5. Assembly of ookcase component completes.
CARE INSTRUCTIONS:
• Dust with a clean, soft cloth.
• Avoid the use of chemicals and harsh cleaning agents.
D5.
D7.
D10.
D11.
D9.
D4.
D1.
D1.
D3.
D7.
D10.
D11.
D9.
ottom
Cut-Out
Corner
ottom
Cut-out
Corner
Cut
-
o
ut
Cut
-
o
ut
D9
10
x
D9
10
x