PB TEEN CHELSEA User manual

Date: 2013-May-10
Rev: 2016-August-16 www.pbteen.com Page 1 of 6
CHELSEA MIRROR HUTCH
ASSEMBLY INSTRUCTIONS

Date: 2013-May-10
Rev: 2016-August-16 www.pbteen.com Page 2 of 6
Important Safety Instructions:
•Please read all instructions carefully before assembling this Vanity Mirror.
•For your safety, assembly by two or more adults is strongly recommended.
•Keep these instructions for future use.
•Use only vendor-supplied hardware to assemble this item. Using unauthorized hardware could jeopardize the
structural integrity of the item.
Pre-assembly:
•Remove all parts and hardware from the box. Place all items on a carpeted or scratch-free work surface, as this
will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
•To avoid accidentally discarding small parts or hardware, do not dispose of any packaging or contents of the
shipping carton until assembly is complete.
•Use the parts and hardware lists below to identify and separate each of the pieces included.
•The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
•The use of power tools to aid in assembly is not recommended. Power tools can damage the hardware and split
the wood.
Parts Included:
(A) Center Mirror (1x)
(B) Left Mirror (1x)
(C) Right Mirror (1x)
(D) Wood Supports (2x)
Required parts (not included):
(E) Chelsea Vanity Desk (1x)
(F) Chelsea Vanity Desk Hutch (1x) (optional)
Hardware Included:
Tools Required (not included):
Philips Head Screwdriver
(G) Bolt
Ø1/4” x 1-1/4” – 16 x
(H) Spring Washer
¼” x Ø11x 1.2mm –16 x
(I) Flat Washer
¼” x Ø 13 x 1 –16x
(J) Ball tip Allen key
M4 x 110 x 30mm – 1x
(K) Screw
3.5mmx 16mm -12x

Date: 2013-May-10
Rev: 2016-August-16 www.pbteen.com Page 3 of 6
Assembly Instruction Steps:
Option 1: Attach the Mirror without the Desk Hutch (F).
1. Carefully place the Center Mirror (A), Left Mirror (B), and Right Mirror (C) on a flat, scratch-free, or carpeted
surface such as a rug or carpet.
2. Attach Wood Support (D) to Desk (E) by inserting 4 sets of Bolts (G), Spring Washers (H), and Flat Washers (I)
through the holes on the wood support (D), to the pre-fixed insert nuts on the back of Desk (E), as seen in the
illustration below.
3. Tighten with the supplied Ball Tip Allen Key (J).
4. Place Center Mirror (A) onto Desk (E) and align the holes on the back of Center Mirror (A), with the holes on
Wood Support (D).
5. Secure with 12 sets of Bolt (G), Spring Washer (H), and Flat Washer (I) through the holes of Wood Support (D),
and to the pre-fixed insert nuts on the back of the Center Mirror (A), as seen in the illustration below.
6. Tighten with Ball Tip Allen Key (J).

Date: 2013-May-10
Rev: 2016-August-16 www.pbteen.com Page 4 of 6
7. Attach the Left Mirror (B) to the Center Mirror (A) by inserting 6 Screws (K) through the holes of the pre-attached
hinges on Center Mirror (A), to the pre-drilled holes on Left Mirror (B), as seen in the illustration below.
8. Tighten with a Phillips Head Screwdriver (not included).
9. Repeat the above steps to assemble the Right Mirror (C).
10. The assembly is complete.
11. If the Vanity does not sit level, adjust the levelers (in or out).

Date: 2013-May-10
Rev: 2016-August-16 www.pbteen.com Page 5 of 6
Option 2: Attach the Mirror with the Desk Hutch (F):
1. Place Hutch (F) onto the top of Desk (E).
2. Align the holes on the back of Hutch (F) with the holes on Desk (E).
3. Attach Wood Support (D) to secure the Desk (E) to Hutch (F).
4. Secure by inserting 8 sets of Bolt (G), Spring Washer (H), and Flat Washer (I) through the holes of the
Wood Support (D), and to the pre-fixed insert nuts on the back of Desk (E) and Hutch (F), as seen in the
illustration below. Tighten with Ball Tip Allen Key (J).
5. Place the Center Mirror (A) onto Hutch (F).
6. Align the holes on the back of the Center Mirror (A) with the holes of Wood Support (D).
7. Insert 8 sets of Bolt (G), Spring Washer (H), and Flat Washer (I) through the holes of the Wood Support
(D), and to the pre-fixed insert nuts on the back of Center Mirror (A), as seen in the illustration below.
8. Tighten with Ball Tip Allen Key (J).
9. Attach the Left Mirror (B) to the Center Mirror (A) by inserting 6 Screws (K) through the holes of the
pre-attached hinges of the Center Mirror (A), to the pre-drilled holes of the Left Mirror (B), as seen in the
illustration below.
10. Tighten with a Phillips Head Screwdriver (not Included).
11. Repeat the above steps to assemble the Right Mirror (C).
4

Date: 2013-May-10
Rev: 2016-August-16 www.pbteen.com Page 6 of 6
12. The assembly is complete.
13. If the Vanity does not sit level, adjust the levelers (in or out).
14. NOTE: Installation of the Anti Tip Kit is REQUIRED. Please follow the separate instructions to secure
the Drawer Chest to the wall by using tipping-restraint kit included.
Care Instructions:
•Dust often using a clean, soft, dry, and lint-free cloth.
•Blot spills immediately and wipe with a clean, damp cloth.
•We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered finish.
•Hardware may loosen over time. Periodically check to make sure all connections are tight.
Re-tighten if necessary.