Argos Aspley 391/8168 User manual

Aspley Dining Table
Dimensions
Dia - 120cm
Height - 74cm
Issue 1 - 03/04/15
Important – Please read these instructions fully before starting assembly
Assembly Instructions - Please keep for future reference 391/8168
If you need help or have damaged or missing parts, call the Customer Helpline:
Homebase = 0345 0778888
341573
341575

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
Handy Hints
•Keep these instruction for future
reference.
• Imported by:
Homebase Ltd.
• If the glass is chipped or broken, stop using the product and
consult the Manufacturer or Supplier.
Glass Safty
Avebury, Milton Keynes
MK9 2NW
• Batch No: 465262 （按订单PO号）
• Date of Manufacture: May.2015（按出货年月）
• Type of glass used: 8mm toughened glass
Warning:
(a) Do not place very hot or very cold items on the glass surface(s) unless adequately thick table mats
are used to prevent such items from coming into contact with the glass.
(b) Do not sit or stand upon the glass surface(s).
(c) Do not use the glass as a chopping surface. Do not strike the glass with hard or pointed items.
(d) When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if
necessary, do not use washing powders or any other substance containing abrasives since these
substances scratch glass.

Components - Panels
Please check you have all the panels listed below
2
12
Table leg x 4
(124.7 x 6.2cm)
Table top
(Dia120cm)
Components - Fittings
Please check you have all the fittings listed below
19mm Bolt x 4
A
40mm Bolt x 4
B
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
C
Plain washer x 4
D
G
E
Connector x 1
Large hex key x 1
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
If you have damaged or missing components, call the
Customer Helpline: Homebase = 0345 0778888
The bolts length is measured from the head to the point (40mm bolt shown)..
Spring washer x 4
F
Small hex key x 1

Step 1
Assembly Instructions
a:
b:
3
2
2
Two person are needed
during assembly.
Carefully place table top
upside down on a
clean protected surface.
2B
D
C
1
Do not fully tighten
bolts at this stage.
Important note:
D
Fix table legs onto
table top one after
one, using bolts ,
spring washers and
plain washers .
1
2
C
a: Fix the first table leg
Follow step a-b-c-d.
b: Fix the second table
leg
Continued on next page.
Do not fully tighten
bolts at this stage.
Important note:
B
B
D
C
11

Step 1 - continued
Assembly Instructions
c:
d:
4
2
B
D
C
1
Do not fully tighten
bolts at this stage.
Important note:
c: Fix the third table leg.
d: Fix the fourth table
leg.
Do not fully tighten
bolts at this stage.
Important note:
B
D
C
11
1
1
11
2

Step 2
Assembly Instructions
Assemble connector
Fix connector to table
legs using bolts .
Assemble is complete
If you need help or have damaged or missing parts, call the Customer Helpline:
Homebase = 0345 0778888
Turn the table upright.
Remove the plastic film
on table top.
Important note: After all the parts are positioned, you
can now fully tighten all bolts fixed on previous steps.
A
E
A
AA
A
E