Pella INSYNCTIVE DESIGNER Series User manual

PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE®TECHNOLOGY | 1
WHAT’S NEEDED:
• PELLA INSYNCTIVE SINGLE-CHANNEL REMOTE (required —sold separately): Operates Pella
Insynctive BLINDS and SHADES.
• PELLA INSYNCTIVE BRIDGE (optional —sold separately): Wirelessly connects your Insynctive
products to a compatible home automation system.*
• PELLA INSYNCTIVE WALL CHARGER (optional —sold separately): Charges battery in Pella
Insynctive BLINDS and SHADES when solar charge is not available. One per household is
strongly recommended.
PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS and SHADES
can be automatically raised and lowered to improve
the comfort and convenience of your home.
PELLA®INSYNCTIVE®PRODUCT GUIDE
Blinds Shades
BLINDS AND SHADES
* For a list of compatible home automation systems, visit Pella.com/Insynctive.

PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE®TECHNOLOGY | 2
TABLE OF CONTENTS
General and Safety Information
n Need Help?
n Have a Home Automation System?
n Warnings
Product Overview
n Specifications
Detailed Instructions
n
Setting Up Pella®Designer Series®
Between-the-Glass Blinds or Shades
n Programming Positions
n Operating Blinds or Shades with Remote
n Tilting Blind Slats
n Syncing to Pella Bridge
n With Home Automation
Additional Instructions
n Charging Battery in Blinds or Shades
n Care and Maintenance
n Replacing Batteries
n Adding or Deleting a Remote
n “Homing” Blinds or Shades
n Resetting to Factory Defaults
Troubleshooting
FCC Compliance and Industry Canada
Limited Warranty
Software License Agreement and Privacy Policy
3
4
5
11
14
15

PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE®TECHNOLOGY | 3
NEED HELP?
For instant access to warranties, troubleshooting information and videos, visit InsynctiveSupport.Pella.com
or call 855-473-5524.
HAVE A HOME AUTOMATION SYSTEM?
To view a list of compatible systems and find instructions on how to sync Pella®Insynctive®products, visit
Pella.com/Insynctive.
Failure to adhere to the warnings below may result in death, serious injury and/or loss of valuables.
• Pella BLINDS and SHADES with Insynctive technology are not 100% reliable for a variety of
reasons. For example, BLINDS and SHADES with Insynctive technology:
— communicate data wirelessly, and wireless data is susceptible to interference or failure.
— require proper installation.
— require a battery with an adequate charge.
— may be damaged after installation.
Therefore, Pella Insynctive products should not be relied upon in situations where life, safety,
and/or protection of valuables are solely dependent on their function. Test each product at least
once per year to help ensure proper operation.
• Pella Insynctive products are not a substitute for careful adult supervision of children.
• Keep battery and other small parts out of reach of children. If small parts are swallowed,
immediately seek medical help.
• Batteries carry the risk of fire, explosion and burns. Do not disassemble or incinerate.
GENERAL AND SAFETY
INFORMATION
WARNINGS

PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE®TECHNOLOGY | 4
SPECIFICATIONS
Frequency: 433.92 MHz (Insynctive®)
Operating Temperature: 32° – 120°F (0° – 49°C)
Operating Humidity: 5% – 95% RH noncondensing
Battery: Rechargeable Lithium Ion battery pack
Typical Battery Life: 3 years (may vary with use)
DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS or SHADES
can be automatically raised and lowered to improve the comfort
and convenience of your home. BLIND or SHADE may be
controlled with SINGLE-CHANNEL REMOTE or a compatible
home automation system. BLIND or SHADE may be programmed
to three custom positions, including an upper position, user position and lower position.
The slats of BLIND may be tilted to control privacy or the amount of light entering a room.
BLIND or SHADE includes a power unit which is located at the bottom of the Hinged Glass
Panel (HGP) and contains rechargeable batteries. The batteries can be charged by: 1) the solar
panel on the exterior side of the unit, requiring approximately 3 hours of direct sunlight a day,
or 2) a Pella Insynctive WALL CHARGER that magnetically couples to a port clipped to the HGP.
A wire tucks into a groove by the gasket on the HGP and provides power from the charger to
the motor located in the headrail of the BLIND or SHADE.
PRODUCT OVERVIEW

PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE®TECHNOLOGY | 5
DETAILED INSTRUCTIONS
See InsynctiveSupport.Pella.com for how-to videos.
SETTING UP PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS
BLINDS OR SHADES
1. Get Started
• To unpack BLIND or SHADE, open the Hinged Glass Panel
(HGP) and remove the cardboard corner protectors and bands
that secure BLIND or SHADE.
• Check to make sure that the wire is firmly seated into the
groove by the HGP gasket. Press any loose portions of the
clip back into the groove in the HGP.
• Close the HGP and ensure that it is securely latched.
• REMOTE ships in a separate package. Unpack REMOTE.
To set up REMOTE, follow Remote Quick Start Guide or
Remote Product Guide, or visit InsynctiveSupport.Pella.com
for more information.
2. Set up BLIND or SHADE
Complete the following steps to set up BLIND or SHADE.
• Locate the wire that runs from the BLIND or SHADE cover
to the battery at the bottom of the unit. For casement
windows, sliding patio doors and hinged patio doors, the
wire will be located on the same side as the HGP latch
releases. For double-hung or Precision Fit®window units,
the wire will be located on the right-hand side of the unit.
• With the HGP closed, touch the top end of REMOTE to
BLIND or SHADE cover approximately 6" from the edge of
the glass on the side where the wire is connected. Move
REMOTE back and forth slowly until BLIND or SHADE
completes a quick up/down motion to indicate BLIND or
SHADE has entered sync mode.
• Press and hold Up button on REMOTE until BLIND or
SHADE completes a quick up/down motion. This will
require the Up button to be pressed for about 3 seconds.
CAUTION: DO NOT remove or cut the white cord that limits
the opening of the HGP. Doing so may cause serious damage,
including glass breakage, to your Pella product. The cord should
only be detached by a qualified technician when performing
service-related procedures.
HINGED
GLASS
PANEL
(HGP)
UP
BUTTON
DOWN
BUTTON
LED
LIGHT
CENTER
BUTTON
SOLAR
PANEL
WIRE
BLIND OR
SHADE
COVER
HGP
LATCH
RELEASE
COVER
REMOTE
MEASURE 6"
FROM END WHERE
WIRE CONNECTS
BATTERY
VIEW WITH HGP OPEN
VIEW WITH HGP CLOSED
CORD

PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE®TECHNOLOGY | 6
• Press and release the Down button to send BLIND or
SHADE to its lower position. If you would like to change
this position, follow the procedure for Programming the
Lower Position on page 7 of this product guide.
• Press and release the Center button to send BLIND or
SHADE to its user position. The user position is set by
the factory at approximately 50% of the distance between
fully opened and fully closed positions. If you would
like to change this position, follow the procedure for
Programming the User Position on page 7 of this
product guide.
• Press and release the Up button to send BLIND or
SHADE to its upper position. If you would like to change
this position, follow the procedure for Programming the
Upper Position indicated below.
• BLIND or SHADE is now ready for use.
PROGRAMMING POSITIONS
See InsynctiveSupport.Pella.com for how-to videos.
REMOTE may be used to program up to three positions to
BLIND or SHADE with Insynctive®technology, including an upper
position, user position and lower position. Once placed into
program mode, REMOTE will stay in program mode until the
programming process is completed, or REMOTE will automatically
exit program mode if no buttons are pressed for 1 minute or if
battery is removed and reinserted.
Programming Upper Position
• Touch the top end of REMOTE to BLIND or SHADE cover
approximately 6" from the end where the wire connects.
Move REMOTE back and forth slowly until BLIND or SHADE
completes a quick up/down motion to indicate BLIND or
SHADE has entered program mode.
• Simultaneously press and hold the Center and Up buttons
until BLIND or SHADE completes a quick up/down motion.
This will require the buttons to be pressed for about 5
seconds. The light on REMOTE will begin blinking when
the buttons are released to acknowledge that REMOTE is
in program mode.
DETAILED INSTRUCTIONS (continued)
UP
BUTTON
DOWN
BUTTON
LED
LIGHT
CENTER
BUTTON
COVER
REMOTE
MEASURE 6"
FROM END WHERE
WIRE CONNECTS

PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE®TECHNOLOGY | 7
• Press the Up or Down button on REMOTE to move BLIND
or SHADE bottom rail to the desired position.
• Press and hold the Center button until BLIND or SHADE
makes a quick up/down movement. This should take about
3 seconds. The light on REMOTE will stop blinking.
Programming User Position
• Touch the top end of REMOTE to BLIND or SHADE cover
approximately 6" from the end where the wire connects.
Move REMOTE back and forth slowly until BLIND or SHADE
completes a quick up/down motion to indicate BLIND or
SHADE has entered program mode.
• Simultaneously press and hold the Up and Down buttons
until BLIND or SHADE completes a quick up/down motion.
This will require the buttons to be pressed for about
5 seconds. The light on REMOTE will begin blinking when
the buttons are released to acknowledge that REMOTE is
in program mode.
• Press the Up or Down button on REMOTE to move BLIND
or SHADE bottom rail to the desired position.
• Press and hold the Center button until BLIND or SHADE
makes a quick up/down movement. This should take about
3 seconds. The light on REMOTE will stop blinking.
Programming Lower Position
• Touch the top end of REMOTE to BLIND or SHADE cover
approximately 6" from the end where the wire connects.
Move REMOTE back and forth slowly until BLIND or SHADE
completes a quick up/down motion to indicate BLIND or
SHADE has entered program mode.
• Simultaneously press and hold the Center and Down
buttons until BLIND or SHADE completes a quick
up/down motion. This will require the buttons to be
pressed for about 5 seconds. The light on REMOTE
will begin blinking when the buttons are released to
acknowledge that REMOTE is in program mode.
DETAILED INSTRUCTIONS (continued)
UP
BUTTON
DOWN
BUTTON
LED
LIGHT
CENTER
BUTTON
COVER
REMOTE
MEASURE 6"
FROM END WHERE
WIRE CONNECTS
COVER
REMOTE
MEASURE 6"
FROM END WHERE
WIRE CONNECTS

PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE®TECHNOLOGY | 8
• Press the Up or Down button on REMOTE to move BLIND
or SHADE bottom rail to the desired position.
• Press and hold the Center button until BLIND or SHADE
makes a quick up/down movement. This should take about
3 seconds. The light on REMOTE will stop blinking.
OPERATING BLIND OR SHADE WITH REMOTE
See InsynctiveSupport.Pella.com for how-to videos.
• Press and release Up button: Pressing the Up button
for less than 1 second will cause BLIND or SHADE to
automatically move to the upper position that has been
programmed by the user.
• Press and hold Up button: Pressing the Up button for
longer than 1 second will cause BLIND or SHADE to move
up until the button is released or until the shade reaches
the fully opened position.
• Press and release Center button: Pressing the Center
button for less than 1 second will cause BLIND or SHADE to
automatically move to the user position.
• Press and release Down button: Pressing the Down
button for less than 1 second will cause BLIND or SHADE
to automatically move to the lower position that has been
programmed by the user.
• Press and hold Down button: Pressing the Down button for
longer than 1 second will cause BLIND or SHADE to move
down until the button is released or until the shade reaches
the fully closed position.
• While BLIND or SHADE is moving to a position, it may
be stopped by pressing either of the other two buttons.
For example, if the Center button is pressed to move the
shade to the user position, the shade will stop moving if
the Up or Down button is pressed.
DETAILED INSTRUCTIONS (continued)
UP
BUTTON
DOWN
BUTTON
LED
LIGHT
CENTER
BUTTON

PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE®TECHNOLOGY | 9
TILTING BLIND SLATS
• To enter tilt mode, press and hold the Center button on
REMOTE until light turns solid red.
• Press and release the Up button to rotate the slats up.
• Press and release the Down button to rotate the
slats down.
• REMOTE will exit tilt mode after 10 seconds of no activity
or when Center button is pressed and held until the light
turns off.
SYNCING TO PELLA®INSYNCTIVE®BRIDGE FOR CONTROL
THROUGH YOUR SMART DEVICE
Ensure that BRIDGE is enrolled in the home automation
network. See Bridge Product Guide for complete
information.
To sync BLIND or SHADE to BRIDGE:
• Touch the top end of REMOTE to BLIND or SHADE cover
approximately 6" from the end where the wire connects.
Move REMOTE back and forth slowly until BLIND or
SHADE completes a quick up/down motion to indicate
BLIND or SHADE has entered sync mode.
• Press and release the Center button on REMOTE three
times within 5 seconds. BRIDGE light will begin blinking
blue. If light does not begin blinking blue, additional
button presses may be required due to the range
between BLIND or SHADE and BRIDGE.
• Follow the inclusion process for the Z-Wave home
automation system to add BLIND or SHADE to the system.
BLIND or SHADE will complete a quick up/down motion
to acknowledge BLIND or SHADE was successfully added
to the home automation system.
• If BLIND or SHADE does not cycle to the top, press and
hold the Up button for about five seconds. BLIND or SHADE
should then make a quick up/down motion and move to
the top.
DETAILED INSTRUCTIONS (continued)
LIGHT
SYNC
BUTTON
TEST
BUTTON
UP
BUTTON
DOWN
BUTTON
LED
LIGHT
CENTER
BUTTON
UP
BUTTON
DOWN
BUTTON
LED
LIGHT
CENTER
BUTTON
COVER
REMOTE
MEASURE 6"
FROM END WHERE
WIRE CONNECTS
BRIDGE

PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE®TECHNOLOGY | 10
WITH HOME AUTOMATION
BRIDGE supports two types of home automation systems:
Professionally Installed and Do-It-Yourself (DIY) Z-Wave. For
a list of compatible home automation systems or syncing
instructions, visit Pella.com/Insynctive.
NOTE: If you have a Z-Wave home automation system, the
order in which you sync BLINDS or SHADES to BRIDGE is the
order by which they will be included into the Z-Wave network.
Write down the order in which each BLIND or SHADE is synced
to BRIDGE so you can identify and assign a name when it shows
up in your Z-Wave network.
DETAILED INSTRUCTIONS (continued)

PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE®TECHNOLOGY | 11
ADDITIONAL INSTRUCTIONS
CHARGING BATTERY IN BLINDS AND SHADES
The solar panel requires approximately 3 hours of direct sunlight each
day to charge the battery for BLIND or SHADE operation solely by
power generated from the exterior solar panel. Additional charging
is necessary when the solar panel on the exterior of the unit does not
receive adequate sunlight.
• First, plug in Pella®Insynctive®WALL CHARGER (sold separately) to
a wall outlet.
• Attach the charger cord to the charge connector on the lower left
or right corner of your unit’s Hinged Glass Panel (HGP).
• Charge for approximately 12 – 24 hours to fully recharge the
BLIND or SHADE battery.
CARE AND MAINTENANCE
Cleaning Between-the-Glass Aluminum Blinds
• First make sure BLIND is in the horizontal (opened) position,
then open the Hinged Glass Panel (HGP). To remove dust, use a
vacuum cleaner with an upholstery brush attachment. You can
remove smudges or fingerprints with a damp cloth.
Cleaning Between-the-Glass Cellular Shades
• Begin by making sure SHADE is fully extended, then open the
HGP. To remove dust, use a vacuum cleaner with an upholstery
brush attachment. Smudges or fingerprints can be carefully
removed with a damp cloth. Never use cleaners with ammonia —
they will damage the fabric. If there are any exposed threads,
trim them and seal them with a fray-check solution (available at
most fabric stores) to reduce fraying. Once SHADE is clean and
dry, raise SHADE before closing the HGP.
Solar Cell
• For optimal performance of the solar cell, keep the exterior
glass surface clean of dust and dirt. It is recommended that the
exterior glass surface be cleaned every six months or whenever
dirt noticeably builds up on the glass. Use an ammonia-free glass
cleaner and soft cloth.
CAUTION: DO NOT remove or cut the white cord that limits the
opening of the hinged glass panel. Doing so may cause serious
damage, including glass breakage, to your Pella product. The
cord should only be detached by a qualified technician when
performing service-related procedures.
HINGED
GLASS
PANEL
(HGP)
SOLAR
PANEL
CORD

PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE®TECHNOLOGY | 12
REPLACING BATTERIES
See InsynctiveSupport.Pella.com for how-to videos.
The battery pack used in this product is recharged by the solar cell
or by using the Pella®Insynctive®WALL CHARGER. Battery life is
dependent upon a number of factors such as number of charge/
discharge cycles and average temperature in the environment.
Battery life is expected to exceed three years in most applications.
When the battery reaches the end of its life, it will lose its charge
quickly and will require charging with the wall charger on a more
frequent basis. Contact your local Pella sales branch to purchase a
replacement battery.
WARNING: Batteries carry the risk of fire, explosion and burns.
Do not disassemble or incinerate. Failure to change battery
properly when low will impair BLIND or SHADE performance.
IMPORTANT NOTES:
— BLIND or SHADE does not need to be resynced to REMOTE or
BRIDGE following a battery change.
— Properly dispose of used batteries based on your local
requirements. A best practice is to dispose of batteries at your
local home chemical collection center. California Only: Contains
perchlorate material. See www.dtsc.ca.gov/hazardouswaste/
perchlorate for any special handling regulations.
ADDING AN ADDITIONAL REMOTE OR DELETING A REMOTE
These procedures may be used to sync or delete a REMOTE from
BLIND or SHADE. A total of 8 REMOTES may be synced to BLIND
or SHADE.
• Touch the top end of REMOTE to BLIND or SHADE cover
approximately 6" from the end where the wire connects.
Move REMOTE back and forth slowly until BLIND or SHADE
completes a quick up/down motion to indicate that BLIND or
SHADE has entered sync mode.
— To add a new REMOTE, press and hold the Up button on
the new REMOTE until BLIND or SHADE completes a quick
up/down motion to acknowledge that new REMOTE was
successfully synced.
— To delete a REMOTE, press and hold the Down button
on REMOTE until BLIND or SHADE completes a quick
up/down motion to acknowledge that REMOTE was
successfully deleted.
ADDITIONAL INSTRUCTIONS (continued)
SOLAR
PANEL
COVER
REMOTE
MEASURE 6"
FROM END WHERE
WIRE CONNECTS
BATTERY

PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE®TECHNOLOGY | 13
“HOMING” THE BLIND OR SHADE
Over time, you may notice that the fully opened position for raise-
and-lower BLINDS or bottom-up SHADES or the fully closed position
for top-down SHADES has drifted. This is due to normal wear and
use of BLIND or SHADE and can be corrected by homing BLIND or
SHADE. The homing process will cause BLIND or SHADE to move up
until it is fully compressed. BLIND or SHADE then resets the position.
To initiate the homing process, press and hold the Up button on
REMOTE until BLIND or SHADE reaches the top point of travel,
then release the button. Press and hold the Up button for about 5
seconds until BLIND or SHADE begins to move up. BLIND or SHADE
will stop moving when fully compressed and will reset the fully
opened or closed position.
RESETTING TO FACTORY DEFAULTS
This procedure will reset all BLIND or SHADE positions to factory
default settings.
• Slide the Hinged Glass Panel (HGP) latch releases side to side
or up and down to open the HGP.
• Locate the small hole in the top cover about 4" from the end
where the wire connects.
• Insert a paper clip or other small tool into the hole, and
depress the reset switch for about 3 seconds.
• BLIND or SHADE will move to top position to acknowledge
successful reset.
ADDITIONAL INSTRUCTIONS (continued)
UP
BUTTON
DOWN
BUTTON
LED
LIGHT
CENTER
BUTTON
WIRE
BLIND OR
SHADE
COVER
HGP
LATCH
RELEASE
FACTORY
RESET
SWITCH

PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE®TECHNOLOGY | 14
TROUBLESHOOTING
PROBLEM
BLIND or SHADE is
moving slowly.
BLIND or SHADE will not move.
BLIND or SHADE will not sync
to BRIDGE.
Bottom rail is not level.
Also refer to InsynctiveSupport.Pella.com for more troubleshooting information, including videos,
frequently asked questions and reference materials.
CAUSE AND POSSIBLE SOLUTION
Batteries are low. Batteries may be recharged with WALL
CHARGER. If problem persists after charging batteries for
12 hours, contact your local Pella sales branch to purchase
a replacement battery.
If the light on REMOTE is blinking, BLIND or SHADE is in
program mode and runs at a slower rate to allow for easier
movement of BLIND or SHADE to the desired position.
Wait 2 minutes, and BLIND or SHADE and REMOTE will
exit program mode.
Verify that all connectors are firmly plugged in at BLIND or
SHADE cover and power unit.
BLIND or SHADE may be in sync mode. Wait 2 minutes and
BLIND or SHADE will exit sync mode, or press and hold the
Up button on REMOTE until BLIND or SHADE makes a quick
up/down motion to exit sync mode.
Batteries are dead in BLIND, SHADE or REMOTE. If REMOTE
light does not come on when buttons are pressed, replace
REMOTE battery. Otherwise, try charging BLIND or SHADE
with WALL CHARGER.
Temperature in the Hinged Glass Panel (HGP) may have
exceeded 160°F. The motor will function once the HGP cools
to below 160°F.
BLIND or SHADE is out of range of BRIDGE. Move BRIDGE
closer to BLIND or SHADE.
BRIDGE has not synced to compatible home automation
system. Sync BRIDGE to system first. Then sync BLIND or
SHADE to BRIDGE and home automation system.
BLIND or SHADE strings are not evenly tensioned. Move BLIND
or SHADE to lower position and then to upper position.

PELLA®DESIGNER SERIES®BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE®TECHNOLOGY | 15
FCC COMPLIANCE AND INDUSTRY CANADA
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a different circuit from the receiver.
• Consult the dealer or an experienced radio/TV contractor for help.
Changes or modifications not expressly approved by Pella Corporation could void the user’s authority to
operate the equipment.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS. L’opération est
soumise aux deux conditions suivantes: (1) cet appareil ne peut causer d’interférences, et (2) cet
appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement de l’appareil.
FCC ID: SO7-206B0000
IC: 11009A-206B0000
LIMITED WARRANTY
A two-year limited warranty comes standard with purchase. For complete warranty details,
visit Pella.com/Warranty.
© 2016 Pella Corporation IDSPG1216