Pentair Pool Products Hydromatic SW33 Manual

SW50
SD50 VS50
SW/SD/VS33 & 50
Submersible
Sump/Effluent
Pumps
SW33
SD33
N
e
w
1
/
2
H
P
M
o
d
e
l
s
SW/SD/VS50
VS33
NOTE! To the installer: Please make sure you provide
this manual to the owner of the pumping equipment or to
the responsible party who maintains the system.
Pump Installation and Service Manual

Thank you for purchasing your
Hydromatic®pump. To help
ensure years of trouble-free
operation, please read the
following manual carefully.
Before Operation:
Read the following instructions
carefully. Reasonable care and
safe methods should be practiced.
Check local codes and
requirements before installation.
Attention:
This manual contains important
information for the safe use of
this product. Read this manual
completely before using this
product and refer to it often for
continued safe product use.
DO NOT THROW AWAY OR
LOSE THIS MANUAL. Keep it
in a safe place so that you may
refer to it often.
WARNING: Before handling
these pumps and controls,
always disconnect the power
first. Do not smoke or use
sparkable electrical devices or
flames in a septic (gaseous) or
possible septic sump.
To reduce risk of electrical shock:
1. Risk of Electrical Shock:
This pump has not been
investigated for use in
swimming pool areas.
2. Risk of Electrical Shock:
Connect only to a properly
grounded receptacle.
Septic tank is to be vented
in accordance with local
plumbing codes.
Do not smoke or use sparkable
electrical devices or flame in a
septic (gaseous) or possible
septic sump.
If a septic sump condition
exists and if entry into sump is
necessary, then (1) provide
proper safety precautions per
OSHA requirements and (2)
do not enter sump until
these precautions are strictly
adhered to.
Do not install pump in location
classified as hazardous per
N.E.C., ANSI/NFPA 70 - 1999.
Failure to heed above cautions
could result in injury or death.
General
Information
Pump
Warning
Approx. Turn-On Level
SW33A 91/2"
SD33A 73/8"
VS33A 83/8"
Approx. Turn-Off Level
SW33A 37/8"
SD33A 37/8"
VS33A 37/8"
Approx. Turn-On Level
SW50A 91/2"
SD50A 77/8"
VS50A 71/2"
Approx. Turn-Off Level
SW50A 31/2"
SD50A 33/8"
VS50A 4"
2. Make sure float (Models
SW33/50 and VS33/50) hangs
free. It should not come into
contact with side or bottom of
sump.
3. Make sure sump is free of
string, cloth, nails, gravel, etc.
before installing pump.
4. Do not set pump directly on
the bottom of sump if it is not
solid. Raise the pump by
using bricks or concrete blocks
underneath it.
5. Use steel or plastic pipe for all
connecting lines between
pump and sewer outlet.
NOTE: Some city regulations
do not allow installing a
pump with plastic pipe.
Check local regulations.
6. Hydromatic check valve
should be installed in
discharge pipe, at least twelve
inches above the discharge
outlet of the pump.
These important instructions
must be followed for satisfactory
performance of your pump.
Before installation, check
your local electrical and
plumbing codes.
1. Provide proper sump.
Minimum Sump Diameter
SW/SD/VS50 18"
SW33 18"
SD/VS33 12"
2
Pump
Installation

3
Example one
SD50
PERFORMANCE CURVE
Example one illustrates a typical system installation.
7. Connect to power source using
3-prong grounded 115 volt
AC receptacle. Do not
remove ground pin from
electrical plug. Do not use an
extension cord.
8. For proper automatic
operation make sure the pump
power cord is plugged into
the back of the piggyback
receptacle on the switch cord.
9. Use pump submerged for
pumping waterlike liquids
(temperature to 120°F).
WARNING: Risk of
Electrical Shock – This
pump has not been
investigated for use in
swimming pool areas.
10.CAUTION: Do not pump
flammable liquids, strong
chemicals or salt water.
11.In applications where the
pump may sit idle for months
at a time, it is recommended
that the pump(s) be cycled
every month to ensure
pumping system is working
properly when needed.
12.An audible alarm system such
as the Q Alert for high water
conditions should be installed
for additional protection
against high water conditions.

4
Pump
Servicing
electrical components of the
pump. Starting with the power
cord, inspect for cuts or nicks
in the insulation. If the cord is
damaged, it must be replaced!
9. Using an ohmmeter, check
the resistance of the motor
windings by connecting one
lead clip to each electric flat
prong on the power cord plug.
The ohmmeter should be on
R x 1 setting.
To check for ground, place the
ohmmeter on R x 100k,
connect one lead clip to the
round ground prong on
the power cord and touch the
other lead clip to each flat
prong individually. If the
reading is other than infinity
(on the ohmmeter scale),
a leakage through stator
insulation or moisture in the
windings is occurring and the
pump must be replaced.
WARNING: Before handling
these pumps and controls,
always disconnect the
power first.
Do not smoke or use sparkable
electrical devices or flames in a
septic (gaseous) or possible
septic sump.
Pump does not run or hum.
1. Line circuit breaker may be
off, blown or loose.
2. Water level in sump may be
too low. Run in more water.
Turn-on level is 12 to 13
inches above sump bottom.
3. Pump and/or switch cord plug
may not be making contact
in receptacle.
Read the following instructions
carefully before replacing any
parts. Reasonable care and safe
methods should be practiced.
Check local codes and
requirements before installation.
Only competent electrician
should make the installations.
Servicing should be performed
only by knowledgeable pump
service contractors or authorized
service stations.
1. WARNING: Always disconnect
the pump from power source
before handling or making any
adjustments. Always wear
rubber boots when there is
water on the floor and you
must unplug the pump.
2. Before removing pump from
sump for repair, check if the
trouble could simply be a
blown fuse, tripped circuit
breaker, or a power cord
not completely inserted into
the receptacle.
3. NOTE: Automatic thermal
overload protects the sealed-
in-oil motor. Running dry will
overheat the motor and
activate the overload protector
until the unit cools.
4. If the unit is being operated
by the optional float control or
diaphragm switch, unplug the
pump from the piggyback
receptacle and plug the pump
directly into the power source.
If the pump starts each time it
is plugged directly into the
receptacle and does not start
each time when plugged into
the piggyback switch with the
float raised up (or the
diaphragm switch pressed in)
to a start position, replace the
complete piggyback switch
assembly and retest with
new assembly.
5. If pump fails the above two
steps, unplug and pull the
pump from the sump by the
handle. Sandblast, if possible,
any dirt or trash from
the outside of the pump
before proceeding.
6. Check for an obstruction in the
impeller cavity by laying the
pump on its side and removing
the screws (10) to remove the
plastic base and bottom plate
(12 & 13). If the impeller does
not rotate freely, clear the
impeller and cavity walls
before reassembling the base.
Repeat Step 4.
7. Air Locking: A sump pump is
said to be air locked if air traps
in the pump and it cannot get
out, thus preventing pump from
operation. Hydromatic sump
pumps have a small air vent
hole in the impeller cavity to let
out trapped air. If the hole
becomes plugged, pump may
air lock. To break the air lock,
use a small screwdriver to
clear the hole in the impeller
cavity. As a secondary
precaution in installations of
this type – 1⁄8" hole should be
drilled in the discharge pipe
below the check valve.
The check valve should be
12 to 18 inches above pump
discharge. Do not put check
valve directly into pump
discharge opening.
NOTE: In sumps where the
pump is operating daily, air
locking rarely occurs.
8. If the above tests have not
resolved the problem, the
problem may be in the
Pump
Troubleshooting

5
4. If pump is using the series cord
plug, the two plugs may not be
plugged tight together.
5. Float may be stuck. Be sure
float operates freely in basin.
6. If all symptoms check OK,
motor winding may be
open; take to service center
for check.
Pump runs but does not
deliver water.
1. Check valve may be installed
backward. Arrow in valve
points in direction of flow.
2. Discharge gate valve, if used,
may be closed.
3. Pump may be air locked. Start
and stop several times by
plugging and unplugging cord.
Check vent hole in pump case
for plugging.
4. Pump head may be too high.
Pump cannot deliver water
over 30' (1⁄2HP), 26' (1⁄3HP)
vertical. Horizontal distance
does not affect pumping,
except loss due to friction.
5. Inlet in pump base may be
clogged. Remove pump and
clean out openings.
6. Impeller or volute openings
may be plugged or
partially plugged. Remove
pump and clean per
maintenance instructions.
Pump runs and pumps out
sump but does not stop.
1. Float is stuck in Up position.
Be sure float operates freely
in basin.
Pump runs but delivers only
small amount of water.
1. Pump may be air locked. Start
and stop several times by
plugging and unplugging cord.
Check vent hole in pump case
for plugging.
2. Pump head may be too high.
Pump cannot deliver water
over 30' (1⁄2HP), 26' (1⁄3HP)
vertical. Horizontal distance
does not affect pumping,
except loss due to friction.
3. Inlet in pump base may be
clogged. Remove pump and
clean out openings.
4. Impeller or volute openings
may be plugged or partially
plugged. Remove pump and
clean per maintenance
instructions.
5. Pump impeller may be
partially clogged causing
motor to run slow, resulting in
motor overload. Clear impeller.
Fuse blows or circuit breaker
trips when pump starts.
1. Inlet in pump base may be
clogged. Remove pump and
clean out openings.
2. Impeller or volute openings
may be plugged or
partially plugged. Remove
pump and clean per
maintenance instructions.
3. Pump impeller may be
partially clogged causing
motor to run slow, resulting
in motor overload. Clear
impeller.
4. Fuse size or circuit breaker is
too small.
5. Defective motor stator: return
to Hydromatic service center
for verification.
Motor runs for short time then
stops. Then after short
period starts again. Indicates
tripping overload caused by
symptom shown.
1. Inlet in pump base may be
clogged. Remove pump and
clean out openings.
2. Impeller or volute openings
may be plugged or
partially plugged. Remove
pump and clean per
maintenance instructions.
3. Pump impeller may be
partially clogged causing
motor to run slow, resulting in
motor overload. Clear impeller.
4. Defective motor stator: return
to Hydromatic service center
for verification.
Your pump warranty is void…
If… power cord has been cut or
spliced.
If… pump has been used to pump
mud, cement, tar, abrasives or
chemicals.
If… pump has been used for
pumping of hot water (above
120°F).
If… pump has been dismantled
by other than authorized
Hydromatic service center or
distributor.

6
SW/SD/VS33 & 50
Parts List

7
SW/SD/VS33 & 50
Parts List
Ref. No. Description Part No. Qty.
1 PLUG – PIPE 14981-001-1 1
2 HANDLE – PUMP 8522-006-1 1
3 SCREW – QUADREX #10-24 x 3/8" 14770-006-1 2
4 SCREW – QUADREX #8-32 x 5/16" 14770-001-1 1
5 WIRE W/ TERMINAL 6000-053-1 1
6 HOUSING – MOTOR 8507-013-5 1
7 SCREW – HHC 1/4-20 x 3/4" 176-005-1 3
8 SHAFT 5482-001-1 1
9 BRG. 65-024-1 1
10 SCREW – MACH 10-24 x 1-1/4" (1/3 HP) 27592C001 5
- SCREW – HHC 1/4-20 x 1-1/4" (1/2 HP) 176-007-1 7
11 IMPELLER (1/3 HP) 8498-003-1 1
- IMPELLER (1/2 HP) 14577-000-1 1
12 BASE – STRAINER (1/3 HP) 8520-002-1 1
- BASE – STRAINER (1/2 HP) 8520-003-1 1
13 PLATE – SUCTION (1/3 HP) 8521-002-1 1
- PLATE – SUCTION (1/2 HP) 8521-003-1 1
14 GASKET – FIBER ((1/2 HP ONLY) 14828-000-1 1
15 CASE – VOLUTE (1/3 HP) 8504-002-2 1
- CASE – VOLUTE (1/2 HP) 8504-005-2 1
16 SEAL – SHAFT ROT. 21607A001 1
18 SEAL – RING 149-001-1 1
19 STATOR (1/3 HP) 14590-001-1 1
STATOR (1/2 HP) 14591-001-1 1
20 SCREW – HEX #8-32 x 3" 145-009-1 2
21 ROTOR (1/3 HP) 14590-010-1 1
- ROTOR (1/2 HP) 14591-010-1 1
22 SEAL – RING 139-014-1 1
24 CORD – POWER – 10' 14623-010-1 1
- CORD – POWER – 20' 14623-020-1 1
25 NUT – CORD 75-005-1 1
27 TIE – PUSH MOUNT 1055-001-1 1
28 SWITCH – FLOAT (10' CORD) 13967-010-1 1
- SWITCH – FLOAT (20' CORD) 13967-020-1 1
29 BRACKET (1/3 HP) 5502-011-1 1
- BRACKET (1/2 HP) 5502-005-1 1
30 SCREW – 1/4-20 x 3/8" 11455-003-1 1
31 SWITCH – DIAPHRAM (10' CORD) 14974-000-5 1
- SWITCH – DIAPHRAM (20' CORD) 14974-001-5 1
32 BRACKET 13871-000-1 1
33 SWITCH – VERT. (10' CORD) 13869-010-1 1
- SWITCH - VERT. (20' CORD) for 1/3 HP models 13869-020-1 1
Ref. No. Description Part No. Qty.

Item # W-03-445 Rev. 9/24/09Part # 5625-445-1
– Your Authorized Local Distributor –
USA
740 East 9th Street, Ashland, Ohio 44805
Tel: [phone] Fax: [phone] www.hydromatic.com
CANADA
269 Trillium Drive, Kitchener, Ontario, Canada N2G 4W5
Tel: [phone] Fax: [phone]
© 2007 Hydromatic®Ashland, Ohio. All Rights Reserved.
LIMITED WARRANTY
HYDROMATIC warrants to the original consumer purchaser (“Purchaser” or “You”) of HYDROMATIC Sump
Pumps, Effluent Pumps, Sewage Pumps (other than 2-1/2"), and Package Systems, that they will be free from
defects in material and workmanship for the Warranty Period of 36 months from date of manufacture.
Our warranty will not apply to any product that, in our sole judgement, has been subject to negligence,
misapplication, improper installation, or improper maintenance. Without limiting the foregoing, operating a
three phase motor with single phase power through a phase converter will void the warranty. Note also that
three phase motors must be protected by three-leg, ambient compensated, extra-quick trip overload relays of
the recommended size or the warranty is void.
Your only remedy, and HYDROMATIC’s only duty, is that HYDROMATIC repair or replace defective products
(at HYDROMATIC’s choice). You must pay all labor and shipping charges associated with this warranty and
must request warranty service through the installing dealer as soon as a problem is discovered. No request
for service will be accepted if received after the Warranty Period has expired. This warranty is not transferable.
EXCEPTIONS: Hydromatic Special Application Pumps, Battery Back-Up Sump Pumps, Filtered Effluent
Pumps, Grinder Pumps, and 2-1/2" Sewage Pumps are warranted for a period of 12 months from date of
purchase or 18 months from date of manufacture, whichever comes first.
HYDROMATIC SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE FOREGOING WARRANTIES
SHALL NOT EXTEND BEYOND THE DURATION EXPRESSLY PROVIDED HEREIN.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on
the duration of an implied warranty, so the above limitations or exclusions may not apply to You. This warranty
gives You specific legal rights and You may also have other rights which vary from state to state.
This warranty supersedes and replaces all previous warranty publications.
HYDROMATIC
740 East 9th Street, Ashland, OH 44805
Phone: [phone] • Fax: [phone] • Web Site: http://www.hydromatic.com