Pentair EVERPURE H Series User manual

EVERPURE®H SERIES WATER FILTRATION SYSTEMS
SISTEMA DE FILTRACIÓN DE AGUA DE LA SERIE H
H SÉRIE SYSTÈME DE FILTRAGE D’EAU

2
INSTALLATION INSTRUCTIONS  ENGLISH
Product Specifications........................................... Page 3
Tools Required ....................................................... Page 4
Basic Installations Instructions............................. Page 4
H-1200 Installations Instructions.....................Pages 6-7
Claims & Notes...................................................... Page 7
INSTRUCCIONES DE INSTALACIÓN  ESPAÑOL
Especificaciones Del Producto........................... Página 8
Herramientas necesarias................................... Página 9
Instrucciones básicas de instalación.................. Página 9
H 1200 Instrucciones de instalación..........Páginas 11-12
Declaraciones y notas....................................... Página 12
INSTRUCTIONS D’INSTALLATION  FRANÇAIS
Caractéristiques Techniques Du Produit............. Page 14
Outils nécessaires ............................................... Page 15
Instructions d’installation de base...................... Page 15
Consignes d’utilisation pour l’H 1200...........Pages 17-18
Revendication & remarques ................................ Page 18

ENGLISH
EVERPURE®H-Series Water Filtration Systems • 3
The Universal Plumbing Code adopted by over 20
states, and other specific state and county codes, prohibit the
use of saddle valves and their use is never recommended. You
must adhere to your state/local plumbing codes. Consult your
licensed plumber if you have related questions.
Do NOT use copper tubing with the John Guest®
Fittings provided with your Everpure Filter System. Copper
tubing may appear to fit, but water leaks will develop over time
and use. If copper tubing is required, you must use copper
compression fittings available from any hardware/plumbing
supply.
CALIFORNIA PROPOSITION 65 WARNING
This product contains chemicals known to the
State of California to cause cancer or birth defects or other
reproductive harm.
THE OWNER’S GUIDE IS APPLICABLE FOR THE
FOLLOWING
EVERPURE FILTER MODELS:
Multiple Appliance Connections: You can also connect your
Everpure Filter to the refrigerator for ice and water, an instant
hot water dispenser or chiller, or a plumbed-in coffee brewer.
Simply install connection “tees” (available from any hardware/
plumbing supply) in the water line between the filter and the
faucet adaptor, and run new tubing to each appliance.
NOTE:
DO NOT connect this system to a commercial ice maker.
These appliances require flow and volume beyond the design
limits of your under-sink filter system.
NOTE: If connecting to a home icemaker and there is no filter
faucet connection under the sink, a flush valve is required.
Thank you for purchasing an Everpure commercial-grade
water filtration system for your home. With your Everpure
system, you get premium quality water direct from your tap
that’s great-tasting, healthful and convenient for you and
your family.
Product Specifications:
•For Cold Water Use Only
•Temperature Range: 35-100°F (2-38°C)
•Min.-Max. Working Pressure:
10-125 psi (0.7-8.6 bar)
•Service Flow Rate: 0.5 gpm (1.9 Lpm)
Model H-54 Rated Capacity: 750 gal (2835 L)*
Model H-300 Rated Capacity: 300 gal (1140 L)*
Model H-104 Rated Capacity: 1,000 gal (3780 L)*
Model H-300-HSD Rated Capacity: 300 gal (1140 L)*
Model H-300-NXT Rated Capacity: 300 gal (1140 L)*
Model H-1200 Rated Capacity: 1,000 gal (3780 L)*
*
For optimum performance, cartridge replacement
is required once a year, or sooner if flow becomes
too slow for convenience, or if the unit’s rated
capacity is reached.
For purchase of replaceable components please contact your local distributor.
H-1200 customers: Instructions for installing the H-1200
begin on page 6 of this Installation and Operation Guide.

ENGLISH
4• EVERPURE®H-Series Water Filtration Systems
BASIC INSTALLATION INSTRUCTIONS
Tools Needed For Installation
• Phillips Screwdriver • Wrench • Pencil
• Utility Knife • Measuring Tape
1. OPEN CARTON & INSPECT PARTS
Installation Parts
Key Description Part No.
1 QL3 Filter Head EV925831
2 Filter Cartridge (varies)
3 2 Locking Washers EV306204
4 2 Screws EV306196
5 Angle Stop Valve Adaptor EV312120
6 Tubing, 1/4" poly A0860119
7
Elbow Fitting Pack Restrictor EV308168
8 Plumbers Tape EV312119
9 Faucet Connector EV312135
10 Everpure Filter Timer EV314160
2. VERIFY UNDERSINK MOUNTING LOCATION
Measure 22” from the base of the cabinet, and mark the
mounting location for the top of the filter head. Make sure
there is adequate space above the head to open and close
the built in shut-off valve and to avoid crimping the water
line tubing. Also, make sure your chosen location offers
easy access for future cartridge changes.
DIMENSION Width Height Depth
H-54 5" 15" 5"
H-104 5" 20" 5"
H-300 5" 22" 5"
H-300-HSD 5" 22" 5"
H-300-NXT 5" 22" 5"
NOTE:
The head and cartridge must be mounted in the
vertical position, with the cartridge hanging down.
1
1
2
3
5
6
7
8
9
10
4
2
22"

ENGLISH
EVERPURE®H-Series Water Filtration Systems • 5
3. MOUNT FILTER HEAD UNDER SINK
A. Identify Filter Head and the two Elbow Fittings, and
note that the Outlet Fitting has a black band. This
fitting includes a small restrictor insert to ensure
maximum flow at 1/2 gallon per minute.
B. Apply Plumbers Tape to the threads of each Elbow
Fitting. Wrap tape in direction of the threads to
assure a tight fit and avoid small leaks.
C. Screw Inlet Elbow Fitting into the left side of the
filter head, and hand tighten only.
D. Screw Outlet Elbow Fitting (black band) into the
right side of the filter head in the same manner.
E. Securely mount the filter head on the cabinet wall
using the enclosed mounting screws and washers.
4. ATTACH INLET WATER SUPPLY
F. Locate and close the cold water Angle Stop Valve
under your kitchen sink. Open cold water line of
faucet to release water pressure.
G. Unscrew and disconnect the braided tubing on top of
the Angle Stop Valve.
H. Attach the bottom of Angle Stop Adaptor to the
existing cold water Angle Stop Valve.
I. Attach the braided tubing to the top of the Angle
Stop Adaptor.
J. Close side valve on Angle Stop Adaptor and open
cold water Angle Stop Valve to return water service
to kitchen sink. Check for leaks.
NOTE:
Plumbers Tape should not be required for
these next steps.
K. Measure length of tubing needed to connect Angle
Stop Adaptor to Inlet Elbow Fitting on Filter Head.
Allow adequate tubing to avoid sharp turns.
L. Cut tubing at a 90° angle using a sharp knife.
M. Insert ends of tubing into quick-connect fittings.
Push tube into fitting and gently pull to confirm a
tight fit.
5. ATTACH FILTERED WATER TO SINK FAUCET
N. Install separate faucet for filtered drinking water.
Follow individual manufacturer’s instructions.
O. Attach Faucet Connector Fitting to bottom end of
threads on new faucet assembly. Plumbers Tape
should not be required for this step.
P. Measure length of tubing needed to connect the
Outlet Elbow Fitting on Filter Head to the new
Faucet Connector Fitting. Allow adequate tubing to
avoid sharp turns. Cut and insert each end of the
tubing into the fittings.
3BCD
E
GH
I
LM
4
F
P
O
N
5