Pentair U3 User manual

U3 - U5 - U6
U3 K U3 K SPEZIAL U5 K U6 KE U6 KD
U3 KS U3 KS SPEZIAL U5 KS U6 KES U6 KDS
EN Instruction Manual
www.pts-jung.co.uk B 42054.33-2020.06

2
ENGLISH
You have purchased a product made by
JUNG PUMPEN and with it, therefore, also
excellent quality and service. Secure this
service by carrying out the installation
works in accordance with the instruc-
tions, so that our product can perform
its task to your complete satisfaction.
Please remember that damage caused
by incorrect installation or handling will
adversely affect the guarantee. There-
fore please adhere to the instructions in
this manual!
This appliance can be used by children
aged 8 years or over and by persons with
limited physical, sensory or intellectual
capabilities, or with limited experience
and knowledge, provided that they are
supervised or have been instructed in
the safe use of the appliance and are
aware of the dangers involved. Children
must not be allowed to play with the ap-
pliance. Cleaning and user maintenance
must not be carried out by children un-
less they are supervised.
Damage prevention in case of failure
Like any other electrical device, this product
may fail due to a lack of mains voltage or a tech-
nical defect.
If damage (including consequential damage) can
occur as a result of product failure, the following
precautions can be taken at your discretion:
•Installation of a water level dependent (under
circumstances, mains-independent) alarm
system, so that the alarm can be heard before
damage occurs.
•Inspection of the collecting tank/chamber for
tightness up to the top edge before – or at the
latest, during – installation or operation of the
product.
•Installation of backow protection for drain-
age units that can be damaged by wastewater
leakage upon product failure.
•Installation of a further product that can com-
pensate in case of failure of the other product
(e.g. duplex unit).
•Installation of an emergency power genera-
tor.
As these precautions serve to prevent or mini-
mise consequential damage upon product fail-
ure, they are to be strictly observed as the man-
ufacturer’s guideline – in line with the standard
DIN EN specications as state of the art – when
using the product (Higher Regional Court Frank-
furt/Main, Ref.: 2 U 205/11, 06/15/2012).
SAFETY INSTRUCTIONS
This instruction manual contains essential in-
formation that must be observed during instal-
lation, operation and servicing. It is therefore
important that the installer and the responsible
technician/operator read this instruction manu-
al before the equipment is installed and put into
operation. The manual must always be available
at the location where the pump or the plant is
installed.
Failure to observe the safety instructions can
lead to the loss of all indemnity.
In this instruction manual, safety information is
distinctly labelled with particular symbols. Dis-
regarding this information can be dangerous.
General danger to people
Warning of electrical voltage
NOTICE!NOTICE! Danger to equipment and operation
Qualication and training of personnel
All personnel involved with the operation, ser-
vicing, inspection and installation of the equip-
ment must be suitably qualied for this work
and must have studied the instruction manual
in depth to ensure that they are suciently
conversant with its contents. The supervision,
competence and areas of responsibility of the
personnel must be precisely regulated by the

3
ENGLISH
operator. If the personnel do not have the ne-
cessary skills, they must be instructed and trai-
ned accordingly.
Safety-conscious working
The safety instructions in this instruction man-
ual, the existing national regulations regarding
accident prevention, and any internal working,
operating and safety regulations must be ad-
hered to.
Safety instructions for the operator/user
All legal regulations, local directives and safety
regulations must be adhered to.
The possibility of danger due to electrical en-
ergy must be prevented.
Leakages of dangerous (e.g. explosive, toxic,
hot) substances must be discharged such that
no danger to people or the environment occurs.
Legal regulations must be observed.
Safety instructions for installation, inspection
and maintenance works
As a basic principle, works may only be car-
ried out to the equipment when it is shut down.
Pumps or plant that convey harmful substances
must be decontaminated.
All safety and protection components must be
re-tted and/or made operational immediately
after the works have been completed. Their ef-
fectiveness must be checked before restarting,
taking into account the current regulations and
stipulations.
Unauthorised modications, manufacture of
spare parts
The equipment may only be modied or altered
in agreement with the manufacturer. The use of
original spare parts and accessories approved
by the manufacturer is important for safety rea-
sons. The use of other parts can result in liability
for consequential damage being rescinded.
Unauthorised operating methods
The operational safety of the supplied equip-
ment is only guaranteed if the equipment is
used for its intended purpose. The limiting val-
ues given in the "Technical Data" section may not
be exceeded under any circumstances.
Instructions regarding accident prevention
Before commencing servicing or maintenance
works, cordon off the working area and check
that the lifting gear is in perfect condition.
Never work alone. Always wear a hard hat, safety
glasses and safety shoes and, if necessary, a
suitable safety belt.
Before carrying out welding works or using elec-
trical devices, check to ensure there is no dan-
ger of explosion.
People working in wastewater systems must be
vaccinated against the pathogens that may be
found there. For the sake of your health, be sure
to pay meticulous attention to cleanliness wher-
ever you are working.
Make sure that there are no toxic gases in the
working area.
Observe the health and safety at work regula-
tions and make sure that a rst-aid kit is to hand.
In some cases, the pump and the pumping me-
dium may be hot and could cause burns.
For installations in areas subject to explosion
hazards, special regulations apply!
APPLICATION
WARNING!
The pump must only be connected to sockets
that have been installed properly in accordan-
ce with the regulations and are protected with
at least 10 A (slow) and RCD-safety switches
(30mA).
DANGER!
The pump must never be used when a person is
in the water.
Submersible pumps from the U3, U5 and U6 se-
ries are suitable for pumping domestic waste
water without stones. This includes also water
from household dishwashers and household
washing machines.
The U3 K spezial can also pump aqueous solu-
tions with up to 10% salt content and conden-
sate from gas condensing boilers.

41
ENGLISH
The U6 can also pump ground water, drainage
silage liquor and liquid manure.
NOTICE! In outdoor applications, only pumps
with at least a 10-metre mains cable must be
used.
When using the pumps, the relevant national
laws, regulations and stipulations must be ad-
hered to, for example:
•Domestic contaminated and waste water
(e.g. EN 12056 in Europe)
•Installation of low voltage systems
(e.g., VDE 0100 in Germany)
For non-standard utilization conditions, further
regulations must be observed (e.g. VDE 0100
in Germany, part 701: bathrooms and shower
rooms; part 702: swimming pools and fountains
and part 737: outdoor use).
Temperatures
The pumped medium must have a temperature
of max 35°C.
The submersible pump is frost-resistant down
to -20°C when stored in dry conditions. When
installed, however, it must not be allowed to
freeze in the water.
Transport
The pump must always be lifted by the handle
and never by the power supply cable! The pump
should only be lowered into deeper chambers or
pits using a rope or chain.
Dimensions [mm]
H B T BS TS
U3 K 255 160 225 195 280
U5 K 280 170 250 205 290
U6 K 335 175 255 210 295
Pumps with special oat assembly, (JP44795)
H BS TS
U3 KS 225 270 220
Pumps with special oat assembly, (JP44207)
H BS TS
U5 KS 280 245 285
U6 KS 335 250 290
Switching points On - Off for built-in switching
Normal Special
● ○ ● ○
U3 KS 215 110 105 45
U5 KS 240 135 - -
U6 KS 270 170 - -

5
ENGLISH
ELECTRICAL
CONNECTION
NOTICE! Only qualied electricians may carry
out electrical works to the pump or the controls.
WARNING!
Before carrying out any works: disconnect the
pump and the controls from the mains and take
steps to ensure that no one else can reconnect
them to the power supply.
The relevant standards (such as EN standards),
country-specic regulations (such as VDE in
Germany), and the regulations of the local power
supply companies must be observed.
NOTICE! Never put the mains plug or a free lead
end in water! If water gets into the plug, this can
cause malfunctions and damage.
Observe the operating voltage (see the type
plate)!
The pump is provided with a winding thermo-
stat. In case of unacceptably high temperatures
it switches off the pump to protect it against
possible damage. Unacceptably high tempera-
tures may result e.g. from dry running or me-
chanical or electrical overload.
CAUTION!
The pump is switched on again automatically af-
ter cooling down - risk of injury!
For this reason, always disconnect the device
from the mains before remedying the fault! In
order to do this, unplug from the mains supply
or remove the pre-fuses of the pump controls!
Rotational direction
Applies only for three-phase pumps. The rota-
tional direction must be checked before instal-
lation! If the rotational direction is correct, the
start-up jolt should be counter-clockwise. If the
rotational direction is wrong, 2 phases of the
supply cable must be swapped over, because a
wrong direction of rotation results in an over-
load of the pump.
Alternating and three-phase current circuit dia-
grams
INSTALLATION
The pump must be installed as shown in the ex-
amples. For installations in accordance with EN
12056-4, the pressure pipe must be laid in a loop
above the local backow level and protected
with a backow prevention valve. The rubber
ap supplied (U3 and U5) is for mobile operation
only.
A correspondingly larger diameter pipe should
be used for longer pressure pipelines to avoid
pipe friction losses.
With any pump that has no automatic switching,
the switch-on and switch-off heights can be set
variably with a separate level control. Our ready
to connect level controls can be installed with-
out specic electrotechnical skills.
The pump housing is automatically vented using
the enclosed bracket. If this is not required, the
vent opening can be closed, such as for mobile
operation.

6
ENGLISH
Dimensions of chamber
Single installation with pump base: 40 x 40 cm
Single installation with guide rail system:
40 x 50 cm and Duplex installation: 50 x 50 cm
Example of installation with guide rail system
Installation
Fix the coupling base rmly to the oor of the
collection chamber using wall plugs and then
mount the guide rail. Next, install the pressure
pipe including the necessary ttings, such as
the non-return valve and shut-off valves.
Reseal the coupling catch at the pump and
tighten it until it is “hand tight”. Finally, t the
pump with the coupling catch onto the guide rail
and lower it into place using a chain xed to the
handle.
Example of installation Duplex unit
NOTICE! The oats of the level controller and
alarm system are installed so that they are freely
movable but not under the inlet. Please observe
the minimum distances. The controls may only
be installed in a dry and well ventilated room!
Flushing device
The pump can keep the intake section at the
bottom of the chamber clear of deposits to a
large extent if you carry out a small modica-
tion. This reduces the performance of the pump
only insignicantly.
This modication is carried out as follows. De-
tach the foot strainer and carefully drill a hole
into the 3 markings with the ø 5 symbols. De-
burr the drillholes. When reattaching the foot
strainer, ensure that the new drill-holes are not
covered by the bars of the foot strainer. The U5
and U6 ranges provide markings on the housing
and the foot strainer to help you.
Low level pumping
Flooded areas can be pumped out leaving only
few mm of residual water without the need for
optional extras, U3K: 5 mm, U5K: 6 mm and U6K:
10 mm. To do so, the foot strainer must be lev-
ered off with a screwdriver. In the case of pumps
with an attached control, the oat switch must
be locked in the ON position. It is not possible
therefore in low level pumping to operate the
pump in switching mode.
To make the pump operate, the drainage hose
must be emptied before each pumping run and
there must be a minimum water level available of,
for U3K: 40 mm, for U5K: 60 mm and for U6K: 90
mm.

7
ENGLISH
CAUTION!
For safety reasons, mobile operation is only al-
lowed with a foot strainer.
If a hose is used as a pressure line, care must
be taken to ensure that for every pumping op-
eration the hose is completely empty before the
pump is submersed. Any residual liquid would
obstruct the ventilation of the pump housing
and therefore also hinder the pumping opera-
tion. For the same reason, the pump would not
operate if it was switched on before being sub-
mersed.
The enclosed rubber ap (not Flutboxand U6)
is tted in the pressure outlet (U3) or in the at-
tached elbow (U5). Ensure that the ap opens in
the direction of ow.
Enlarging the free passage
The free passage of the U5 and U6 pump ranges
can be enlarged from 10 to 20 mm. This is done
by levering off the foot strainer and attaching
the enclosed extensions to the integrally mold-
ed pump feet. The foot strainer no longer ts
under the pump.
NOTICE! If the pump is malfunctioning, part of
the contents of the oil reservoir could escape
into the pumping medium.
MAINTENANCE
Maintenance and inspection of this product
must be carried out in accordance with EN
12056-4.
WARNING!
Before carrying out any works: disconnect the
pump and the controls from the mains and take
steps to ensure that no one else can reconnect
them to the power supply.
WARNING!
Check the mains cable for signs of mechanical
and chemical damage. Damaged or kinked ca-
bles must be replaced by the manufacturer.
NOTICE! If the water contains high levels of iron
or lime, insucient cleaning can result in irre-
parable damage to the seal and thus also to the
pump motor in the long term.
Consequently, the pump must be cleaned at
regular intervals according to the hardness of
the water.
Cleaning
The foot strainer prevents coarse impurities
from entering the pump. Regular cleaning of the
oat and the foot strainer ensures optimum per-
formance and operation.
Cleaning of the impeller (U5 and U6)
To clean the impeller, and in the event of an
obstacle or blockage, the foot strainer must be
levered off. After this, take out the screws on the
underside of the pump and remove the cover.
The impeller can now be cleaned.
CAUTION!
Worn impellers can have sharp edges.
If the pump performance decreases, the impel-
ler must be checked for wear and replaced only
by the manufacturer if necessary.
Tightening torque MAfor A2 screw materials
for M 5 MA= 5 Nm
for Amtec 3,5 MA= 1 Nm
for Amtec 5,0 MA= 2 Nm

8
ENGLISH
QUICK TIPS FOR
REMEDYING FAULTS
Pump does not work
•Check mains current (do not use a pin gauge)
•Fuse faulty = may be too weak (please refer to
Electrical Connection)
•Mains supply cable damaged = repair to be
carried out by manufacturer only
Pump runs but does not pump
•Empty the pressure pipe or hose to allow the
non-return valve to open and the air to escape
from the pump housing, it may be necessary
to carry out a ventilation drilling
Impeller blocked
•Solids and brous matter have become lod-
ged in the pump housing = clean
Decreased pumping performance
•Foot strainer obstructed = clean
•Pressure pipe obstructed = clean
•Rotor worn out = repair to be carried out by
the manufacturer
•Wrong direction of rotation (for a three-pha-
se current) = ask a qualied electrician to
change 2 phases of the supply line
0197
JUNG PUMPEN GmbH - Industriestr. 4-6
33803 Steinhagen, Germany
13
401.14.1810
EN 12050-2:2001
Lifting plant for faecal-free wastewater DN 32
U3 K (JP00205/2)
U3 K spez. (JP09562/2)
U3 KS (JP00206/2)
U3 K spez. (JP44255)
U3 KS (JP09808/2)
U3 KS spez. (JP09563/2)
U3 KS spez. (JP45195)
U5 K (JP09386/0)
U5 KS (JP09387/0)
U5 KS (JP09417/0)
U6 K E (JP00226/2)
U6 K D (JP00228/3)
U6 K ES (JP00227/2)
U6 K ES (JP09260/2)
U6 K DS (JP00229/3)
U6 K DS (JP09261/3)
Collecting and automatically lifting faecal-free
waste water above the backow level in buildings
and sites
REACTION TO FIRE NPD
WATERTIGHTNESS Pass
EFFECTIVENESS (LIFTING EFFECT
- Pumping of solids Pass
- Pipe connections Pass
- Ventilation NPD
- Minimum ow velocity Pass
-
Minimum free passage of the plant Pass
- Minimum useful volume NPD
MECHANICAL RESISTANCE
- Load bearing capacity and structural
stability of collection tank for use
NPD
- Structural stability of collection tank
for use inside buildings
NPD
NOISE LEVEL 70 dB(A)
DURABILITY
- of structural stability NPD
- of lifting effectiveness Pass
- of mechanical resistance NPD
DANGEROUS SUBSTANCES NPD

9
EN - Technical Data
U3 K/KS U5 K/KS U6 KE/KES U6 KD/KDS U3 KS U6 KES
[kg] 3,7 / 3,4 4,7 / 4,5 5,9 / 5,3 6,6 / 5,8 3,4 5,3
DN 32 32 32 32 32 32
[mm] 10 10 / 20 10 / 20 10 / 20 10 10 / 20
P1 [W] 320 520 750 750 320 750
P2 [W] 200 380 490 550 200 490
U [V] 1/N/PE ~230 1/N/PE ~230 1/N/PE ~230 3/PE ~400 1/N/PEx230
1/N/PEx230
f [Hz] 50 50 50 50 60 60
I [A] 1,4 2,3 3,3 1,3 1,4 3,3
EN - Performance
H [m] 1 2 3 4 5 6 7 8 9
Q [m3/h]
U3 6,5 5,5 5,0 4,0 3,0 1,5
U5 11,5 10,5 9,0 7,5 6,5 4,5 2,5
U6 15,5 14,5 13,0 11,5 9,5 8,0 6,0 4,0 1,5

10
Shift shaft JP42770
Microswitch JP46351
①Schaltwelle
②Mikroschalter
③Kondensator Capacitor
JP46353
④Anschlusseinheit Top cover
JP46379
JP46380
JP46384
JP46522
JP46381
JP46382
U3 K, 10m
U3 KS, 4m
U3 KS, 10m
U3 K spez., 5m
U3 K spez., 10m
U3 KS spez., 4m
U3 KS spez., 10m
JP46383
Float JP42771
Rubber ap JP46356
Impeller
JP46358
JP46378
Motor
JP46361
JP46362
Elbow JP46355
Screw set JP42773
Volute casing JP46359
Seal set JP46354
⑤Schwimmer
⑥Gummiklappe
⑦Laufrad
U 3 K
U 3 K spezial
⑧Motor
U 3 K
U 3 K spezial
⑨Winkel
⑩Schraubensatz
⑪Spiralgehäuse
⑫Dichtungssatz
⑬Siebfuß Strainer base
JP46360
Spare parts
U3K /2 · U3KS /2 ·U3K SPEZIAL /2 · U3KS SPEZIAL /2

11
Shift shaft JP42770
Microswitch JP46351
①Schaltwelle
②Mikroschalter
③Kondensator Capacitor
JP46015
④Anschlusseinheit Top cover
JP46389
JP46390
U5 K, 10m
U5 KS, 4m
U5 KS, 10m
JP46391
Float JP42771
Motor JP46388
Seals JP46385
Impeller JP46363
Elbow JP46355
Rubber ap JP46366
Volute casing JP46364
Seal set JP46354
Cover JP46387
Screw set JP42773
⑤Schwimmer
⑥Motor
⑦Dichtungen
⑧Laufrad
⑨Winkel
⑩Gummiklappe
⑪Spiralgehäuse
⑫Dichtungssatz
⑬Deckel
⑭Schraubensatz
⑮Siebfuß Strainer base
JP46365
U5K · U5KS
Spare parts

12
U6 KE /2 · U6 KES /2 ·U6 KD /3 · U6 KDS /3
Spare Parts
Motor contactor
JP46371
Microswitch
JP46351
JP46352
Cable
JP42776
JP42777
JP42778
JP42779
JP47221
Shift shaft JP42770
Float JP42771
Capacitor JP46374
Top cover
JP46919
JP46920
JP46372
JP46373
Elbow JP46355
Volute casing JP46368
Seals JP46370
Motor
JP46375
JP46376
Impeller JP46369
Screw set JP42773
Cover JP42772
Seal set JP46354
①Schaltschütz
②Mikroschalter
ES
DS
③Leitung
E / ES, 4 m
E / ES, 10 m
D / DS, 4 m
D / DS, 10 m
10 m, A/NZ-plug
④Schaltwelle
⑤Schwimmer
⑥Kondensator
⑦Haube
E
D
ES
DS
⑧Winkel
⑨Spiralgehäuse
⑩Dichtungen
⑪Motor
E / ES
D / DS
⑫Laufrad
⑬Schraubensatz
⑭Deckel
⑮Dichtungssatz
⑯Siebfuß Strainer base
JP46367

13
JUNG PUMPEN GmbH - Industriestr. 4-6 - 33803 Steinhagen - Germany - www.jung-pumpen.de
DE - Wir erklären in alleiniger Verantwortung, dass das Produkt den aufgeführten Richtlinien entspricht.
CS - Prohlašujeme na svou výlučnou odpovědnost, že výrobek odpovídá jmenovaným směrnicím.
DA - Vi erklærer under ansvar at produktet i overensstemmelse med de retningslinjer
EN - We hereby declare, under our sole responsibility, that the product is in accordance with the specied Directives.
FI - Me vakuutamme omalla vastuullamme, että tuote täyttää ohjeita.
FR - Nous déclarons sous notre propre responsabilité que le produit répond aux directives.
HU - Kizárólagos felelősségünk tudatában kelentjük, hogy ez a termék megfelel az Európai Unió fentnevezett irányelveinek.
IT - Noi dichiariamo sotto la nostra esclusiva responsabilità che il prodotto è conforme alle direttive citate
NL - W verklaren geheel onder eigen verantwoordelkheid dat het product voldoet aan de gestelde richtlnen.
PL - Z pełną odpowiedzialnością oświadczamy, że produkt odpowiada postanowieniom wymienionych dyrektyw.
RO - Declarăm pe proprie răspundere că produsul corespunde normelor prevăzute de directivele mai sus menţionate.
SV - Vi försäkrar att produkten på vårt ansvar är utförd enligt gällande riktlinjer.
SK - Na výlučnú zodpovednosť vyhlasujeme, že výrobok spíňa požiadavky uvedených smerníc.
CE 301-14-1808
Steinhagen, 20-08-2018
______________________ i.V. ____________________
Stefan Sirges, General Manager Rüdiger Rokohl, Sales Manager
• 2006/42/EG (MD) EN 809:1998/AC:2010, EN ISO 12100:2010, EN 60335-1:2012/A11:2014
• 2011/65/EU (RoHS)
• 2014/30/EU (EMC) EN 55014-1:2006/A2:2011, EN 55014-2:1997/A2:2008, EN 60034-1:2010
EN 61000-3-2:2014, EN 61000-3-3:2013
DE - Richtlinien - Harmonisierte Normen
CS - Směrnice - Harmonizované normy
DA - Direktiv - Harmoniseret standard
EN - Directives - Harmonised standards
FI - Direktiivi - Yhdenmukaistettu standardi
FR - Directives - Normes harmonisées
HU - Irányelve - Harmonizá szabványok
IT - Direttive - Norme armonizzate
NL - Richtlnen - Geharmoniseerde normen
PL - Dyrektywy - Normy zharmonizowane
RO - Directivă - Norme coroborate
SK - Smernice - Harmonizované normy
SV - Direktiv - Harmoniserade normer
U3 K (JP00205/2)
U3 KS (JP00206/2)
U3 KS (JP09808/2)
U3 K SPEZ. (JP09562/2)
U3 K SPEZ. (JP44255)
U3 KS SPEZ. (JP09563/2)
U3 KS SPEZ. (JP45195)
U5 K (JP09386/0)
U5 KS (JP09387/0)
U5 KS (JP09417/0)
U6 K E (JP00226/2)
U6 K D (JP00228/3)
U6 K ES (JP00227/2)
U6 K ES (JP09260/2)
U6 K DS (JP00229/3)
U6 K DS (JP09261/3)
J 67 ET (JP09153/1)
J 67 DT (JP09154/1)
UB 62 ES (JP09818/3)
UB 62 DS (JP09819/2)
UB102 ES (JP09283/0)
UB102 DS (JP00534/8)
UB152 ES (JP09439/0)
UB152 DS (JP09440/0)
UB251 DS (JP09298/1)
EU-Konformitätserklärung
EU-Prohlášeni o shodě
EU-Overensstemmelseserklæring
EU-Declaration of Conformity
EU-Vaatimustenmukaisuusvakuutus
EU-Déclaration de Conformité
EU-Megfelelöségi nyilatkozat
EU-Dichiarazione di conformità
EU-Conformiteitsverklaring
EU-Deklaracja zgodności
EU-Declaraţie de conformitate
EU-Vyhlásenie o zhode
EU-Försäkran om överensstämmelse
DE - Weitere normative Dokumente CS - Jinými normativními dokumenty DA - Andre nor-
mative dokumenter EN - Other normative documents FI - Muiden normien FR - Autres
documents normatifs HU - Egyéb szabályozó dokumentumokban leírtaknak IT - Altri docu-
menti normativi NL - Verdere normatieve documenten PL - Innymi dokumentami normaty-
wnymi RO - Alte acte normative SK - Iným záväzným dokumentom SV - Vidare normerande
dokument:
EN 60335-2-41:2003/A2:2010
EN 62233:2008/AC:2008
DE - Bevollmächtigter für technische Dokumentation CS - Oprávněná osoba pro tech-
nickou dokumentaci DA - Autoriseret person for teknisk dokumentation EN - Au-
thorized person for technical documentation FI - Valtuutettu henkilö tekninen do-
kumentaatio FR - Personne autorisée à la documentation technique HU - Hivatalos
személy műszaki dokumentáció IT - Persona abilitata per la documentazione tecnica
NL - Bevoegd persoon voor technische documentatie PL - Pełnomocnik ds. dokumentacji
technicznej RO - Persoană autorizată pentru documentatiei tehnice SK - Oprávnená osoba
pre technickú dokumentáciu SV - Auktoriserad person för teknisk dokumentation:
JUNG PUMPEN - Stefan Sirges - Industriestr. 4-6 - 33803 Steinhagen

Pump Technical Services Limited, Pump House, Unit 12 Bilton Road Industrial Estate, Erith, Kent, DA8 2AN.
Tel: [phone] Email: [email protected]