Perenio PECWS01 User manual

Installation and Operation Manual
for Perenio® PECWS01
Door & Window Sensor
July, 2021

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1
Page 3of 38
Introduction
The Door & Window Sensor is activated when the door or the window where it is
installed opens or closes. It can be used as a part of the Perenio Smart Building
Management System after being connected via the Control Gateway/IoT Router.
The present Manual contains a detailed description of the Door & Window Sensor, as
well as instructions for its installation and operation.
Copyrights
Copyright of ©Perenio IoT spol s r.o. All rights reserved.
The Perenio® trademark is owned by Perenio IoT spol s r.o. (hereinafter referred to
as the Perenio IoT). All other similar trademarks and names, as well as logos and other
symbols are the property of their respective owners*.
All materials under Perenio® tradename contained therein are protected in
accordance with international and local laws including Acts on copyrights and related
rights.
Any reproduction, copying, publication, as well as further distribution or public display
of materials contained in the present document (whether in full or in part) shall not be
allowed until an appropriate permission of the copyright owner is obtained. Any
unauthorized usage of materials contained herein may lead to civil liability and criminal
prosecution in accordance with applicable laws.
Any eventual mentioning of other company names and equipment in the present
document is made solely for the purpose of clarifying and describing the device
operation and shall not infringe on the third party’s intellectual property rights.
*ZIGBEE is the registered trademark of ZigBee Alliance; iOS is the registered trademark of CISCO TECHNOLOGY, INC.;
Android is the registered trademark of Google Inc.; Google Play is the trademark of Google Inc.; App Store is the
registered trademark of Apple Inc.; Linux is the registered trademark of Linus Torvalds.

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved
Page 4of 38
Responsibility and Technical Support
The present document is prepared in accordance with all necessary requirements and
contains detailed information on the device installation, configuration and control valid
as of the date of its issue.
Perenio IoT reserves the right to modify the device and make corrections or changes
to this document without prior notice of the User, and shall not be responsible for any
potential negative consequences which may arise from the use of an outdated version
of the document, as well as for any possible technical and/or typographical errors,
either omitted or accidental, or any related damage that may result from the document
transfer or the use of devices.
Perenio IoT shall make no guarantee with respect to any data contained herein
including but not limited to the device merchantability and fitness for a particular
purpose.
In case of any discrepancies between language versions of this document, the Russian
version of this User Manual shall prevail.
For any technical issues, please contact your local Perenio IoT representative or the
Tech Support Department at perenio.com.
The most common problems may be found in Section 7 of the present document and
at perenio.com where you can also download the latest version of this Installation
and Operation Manual.
Manufacturer:
Perenio IoT spol s r.o.
Na Dlouhem 79, Ricany –Jazlovice 251 01, Czech Republic
perenio.com

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1
Page 5of 38
Conformance to Standards
The device is CE certified and complies with requirements of the
following Directives of the European Union:
2014/53/EU Radio Equipment Directive (RED);
2004/30/EU Electromagnetic Compatibility Directive.
The device complies with the UKCA marking requirements for
selling the device in the UK
The device has passed all procedures of assessments established
in Technical Regulations of the Customs Union and conforms with
standards of the Customs Union
The device complies with the requirements of Restriction of the Use
of Certain Hazardous Substances in Electronic and Electrical
Equipment (2011/65/EU Directive)
The device complies with requirements of the Technical Regulations
of the Republic of Belarus TR 2018/024/BY (Telecommunications.
Security)
The national conformity mark of the Ukraine indicating that the
device meets requirements of all applicable technical regulations
The crossed-out trash can symbol is used to label electrical and
electronic equipment, and indicates its separate collection.
The symbol is given in accordance with the Directive 2012/19/EU
on Waste Electrical and Electronic Equipment (WEEE)* and
indicates that this equipment requires separate collection at the
end of its life and must be disposed of separately from unsorted
household waste.
To protect the environment and human health, please dispose of
used electrical and electronic equipment according to approved
safe disposal guidelines

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved
Page 6of 38
Details on available Certificates are specified in
Section 6 of the present document. For copies
of Certificates and Reports, please visit a
corresponding Section at perenio.com.
BG
CZ
DE
ES
FR
GR
IT
KZ
LT
LV
NL
NO
PL
RO
RU
SE
SK
TR
UA
UK

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1
Page 7of 38
Table of Contents
Introduction ..................................................................................................... 3
Copyrights ....................................................................................................... 3
Responsibility and Technical Support................................................................... 4
Conformance to Standards................................................................................. 5
Table of Contents.............................................................................................. 7
1 General Description and Specifications ............................................................. 9
1.1 General Purpose ....................................................................................... 9
1.2 Technical Specification ............................................................................ 11
1.3 Scope of Delivery.................................................................................... 12
1.4 Packaging and Labelling .......................................................................... 13
1.5 Safe Operation Rules .............................................................................. 13
1.6 Standalone Operation of Perenio® Sensors ............................................... 14
2 Installation and Setup................................................................................... 15
2.1 First Installation and Configuration ........................................................... 16
2.2 Sensor Control Panel............................................................................... 21
2.2.1 Armed Mode ..................................................................................... 21
2.2.2 Battery Level .................................................................................... 22
2.2.3 Event History.................................................................................... 22
2.2.4 Device Scenarios............................................................................... 23
2.2.5 Additional Settings ............................................................................ 26
2.3 Changing the Room or Location for the Sensor .......................................... 28
2.4 History and Push-Notifications.................................................................. 29
2.5 Battery Replacement............................................................................... 30
3 Maintenance and Repair................................................................................ 31
4 Warranty Obligations .................................................................................... 32
5 Storage, Transportation and Disposal of Devices ............................................. 35
6 Other Information ........................................................................................ 36
7 Troubleshooting ........................................................................................... 37
8 Glossary...................................................................................................... 38

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved
Page 8of 38
Figures and Tables
Figure 1 –Door & Window Sensor Exterior ...........................................................9
Figure 2 –Door & Window Sensor Components ..................................................10
Figure 3 –Scope of Supply...............................................................................13
Figure 4 –Examples of Installation....................................................................15
Figure 5 –Installation rules for the Sensor and the Magnet..................................17
Figure 6 –Add new device (Sensor) procedure ...................................................20
Figure 7 –Positioning of the battery in the Door & Window Sensor .......................30
Table 1 –Light indicator states .........................................................................10
Table 2 –Basic Technical Specifications of the Door & Window Sensor ..................11
Table 3 –Typical Errors and Troubleshooting Methods.........................................37
Connection to the Perenio Smart Mobile App
A. SWITCHING ON AND INSTALLATION OF THE DOOR & WINDOW SENSOR ..........16
B. LOGIN TO THE EXISTING USER ACCOUNT......................................................18
C. CONNECTION TO THE CONTROL GATEWAY/IOT ROUTER .................................19

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1
Page 9of 38
1 General Description and Specifications
1.1 General Purpose
The PECWS01 magnetic sensor is a device that sends corresponding signals to the
Perenio® Control Gateway/IoT Router when the magnet is moved away from the
main part of the device to a distance of more than 20-30 mm or is returned back to
initial state.
The PECWS01 Door & Window Sensor has a number of distinctive features, namely:
Timely notification of a window or door opening;
Connection distance –up to 40 meters;
iOS and Android smartphone compatibility;
Support of Zigbee Protocol;
Impact-resistant casing material;
Installation using 3M Tape or screws;
Ability to adjust the Sensor installation level;
Operation with one battery for up to 2 years;
Small size and stylish design.
Figure 1 –Door & Window Sensor Exterior

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved
Page 10 of 38
Figure 2 –Door & Window Sensor Components
Table 1 –Light indicator states
Indicator
Status
Description
Red
Blinking slowly
Sensor is on, and the process of connecting to
the IoT Router/Control Gateway and activation
in the mobile app is started
Blinking fast
Reset was successful, the sensor was deleted
from the mobile app
Off
The sensor is on, activated in the mobile app,
and is in the working order
Sensor is off
Mounting
Panel
Mounting
Holes
Place for
Battery
Sensor
Magnet
Reset
Button
LED
Indicator

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1
Page 11 of 38
ATTENTION! All Products and the Mobile Application of the Company (including
any future software and hardware whether in-house or third-party developed) are
not intended for emergency responses and cannot be used as fire-extinguishing
equipment and/or for emergency intervention, including but not limited to fires,
flooding, gas leaks or explosions, burglary and theft, as well as natural disasters
and other force majeure circumstances leading to damage and/or losses incurred
by the Client or caused to their estates, personal property and/or other products,
devices, personal data and privacy.
1.2 Technical Specification
Table 2 –Basic Technical Specifications of the Door & Window Sensor
Parameter
Value
Article
PECWS01
Microprocessor
NXP5169 (Zigbee IC)
Communication
Technology
Zigbee HA 1.2 (IEEE 802.15.4)
Operating Frequency
2.4GHz
Connection Radius
up to 40 meters (open area)
Zigbee Antenna
Type: Built-in
Transmitting Power: 5.5dBm
Receiver Sensitivity: -90dBm
Antenna Gain: 1.5dBi to 1.8dBi
Repeater: N/A
Distance between the
sensor and the magnet
(Actuation distance)
≥ 25±5 mm
Reset Button
Side panel of the Sensor
Standalone Operation
N/A
Power Type
CR2032 Battery (125mAh, 3V), 1pc.
Power Consumption
Standby Mode: not more than 0.0016mA

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved
Page 12 of 38
Parameter
Value
Alarm Mode: not more than 19mA
Battery Level
Yes (Available in the Mobile App)
Operating Temperature
0°C to +45°C
Operating Humidity
10% to 85% (non-condensing)
Storage Temperature
-10°C to +50°C
Storage Humidity
10% to 95% (non-condensing)
Installation
Edge of the door/window frame (for indoor installation
only)
Casing Material
ABS/PC
Color
White
Dimensions (L x W x H)
Sensor size: 45mm x 30mm x 19mm
Magnet size: 45mm x 15mm x 19mm
Weight
24.2g (32.4g with accessories)
Warranty Period
24 months
Service Life
24 months
Certification
CE, EAC, RoHS, UA.TR
1.3 Scope of Delivery
The following items and accessories are supplied within the Perenio® PECWS01 Door
& Window Sensor package:
1. PECWS01 Door & Window Sensor with a magnet (1 set)
2. Battery (CR2032) (1 pc.)
3. Screws and dowels (1 set)
4. Reset pin (1 pc.)
5. 3M Tape (2 pcs.)
6. 3M Sponge (1 pc.)
7. Quick Start Guide (1 pc.)
8. Warranty Card (1 pc.)
9. Sticker (1 pc.)

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1
Page 13 of 38
1
2
3
4
5
6
Figure 3 –Scope of Supply*
*Images of accessories are provided for informational purposes only
1.4 Packaging and Labelling
The Perenio® PECWS01 Door & Window Sensor is supplied in an individual blister
package of 171mm x 126mm x 27mm (L x W x H) containing the full name and
marking of the device, the list of accessories provided and basic technical specifications
thereof, as well as the date of manufacture and information about the Manufacturer
of devices.
Weights of the blister package are as follows:
Net weight: 33g;
Gross weight: 60g.
1.5 Safe Operation Rules
For the proper and safe operation of Perenio® sensors, follow the instructions and
safety procedures described in the present Manual. The Manufacturer shall not be
liable for any damage caused as a result of improper operation of devices.
Safe Operation Conditions
1. The device shall be installed indoors only.
2. The User must follow rules for installation and positioning of the Sensor and
the Magnet relative to each other as specified in Section 2 of this Manual.
3. The Users shall observe storage/transportation conditions, as well as the
operating temperature mode of the device as declared by the Manufacturer.
4. The User shall not install the device in the area with high humidity and high
content of dust.

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved
Page 14 of 38
5. The User must not disassemble or attempt to repair the device on their own.
6. The User must not drop, throw or bend the device.
7. In order to avoid personal injury, it shall not be allowed to use the cracked or
in any other way damaged device.
8. Use dry cloth or cloth soaked in a small amount of water for cleaning (don’t
use harsh chemicals/cleaning agents). The device must be powered off before
cleaning.
9. Children shall not be allowed to use the device unsupervised and/or play with it.
1.6 Standalone Operation of Perenio® Sensors
The Control Gateway/IoT Router in not necessarily required for all Perenio® Sensors
in order to alert Users on potentially dangerous situations.
So, the Door & Window Sensor cannot be used as a standalone device, i.e. when the
door or window opening is detected, it will not give any sound signal. Therefore, its
operation is arranged by sending notifications to the smartphone. However, to run
active scenarios, the User must have an installed Perenio Smart Building
Management System Mobile App and an activated Control Gateway/IoT Router, as
well as unite the above devices in a system.

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1
Page 15 of 38
2 Installation and Setup
Before installation, the User shall select one of the following possible locations and
mounting modes for the device:
On a horizontal surface (box, trunk, cellar door, etc.);
On a vertical surface (door or window frame, etc.);
Using 3M mounting tape or screws.
Also, make sure that the selected location meets the following requirements:
Absence of metal surface in the installation site of the Sensor;
Ability to install the Sensor and the Magnet coaxially (with/without the 3M
Sponge);
Flat and stable surface in the installation site of the Sensor.
NOTE. It is not recommended to install the device in areas with a high level of
noise and a high-frequency interference. Reinforced concrete floors may reduce
the distance of wireless signal transmission. It is recommended to install the Door
& Window Sensor at a minimum distance from the Control Gateway/IoT Router.
Figures below show possible installation locations for the Sensor:
Figure 4 –Examples of Installation*
* Images are provided for informational purposes only
For installation of the Door & Window Sensor using 3M tape, it is necessary to prepare
the surface as follows:
1. Wipe the surface of the Sensor to which the 3M tape will be attached with alcohol
and wait until it is dry.
2. Attach the 3M tape to the Sensor surface.
3. Make sure that the place of installation is smooth and free from dust, dirt, etc.

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved
Page 16 of 38
4. Wipe the surface to which the 3M tape will be attached with alcohol and wait
until it is dry.
5. Attach the device in the place of installation using the 3M tape.
The entire process of setting-up the Sensor can be divided into several key stages:
Logging in to the User Account of the Perenio Smart Mobile App;
Checking for the availability of the CG/IoT Router connected to the mains and
the Internet;
Connection of the Sensor to the Control Gateway/IoT Router.
2.1 First Installation and Configuration
In order to connect the Door & Window Sensor to the Control Gateway/IoT Router
through the Perenio Smart Mobile App, it is necessary to perform the following steps:
1. Unpack the Sensor and switch it on (See par. Abelow).
2. Login in to the Perenio Smart Building Management System User Account
(See par. Bbelow).
3. Connect the Sensor to the Control Gateway/IoT Router (See par. Cbelow).
4. Enter the desired Sensor name and select the Room of installation.
5. Install the Sensor in the selected room.
A. SWITCHING ON AND INSTALLATION OF THE DOOR & WINDOW SENSOR
To install the Perenio® PECWS01 Door & Window Sensor,follow steps below:
1. Unpack the device.
2. Choose a suitable installation area for the Sensor and the Magnet (window
frame, door leaf, etc.) as follows:
a. Attach the Sensor on the door or window frame using 3M tape (See
Figure 5-a). You can also mount the Sensor using the screw;
b. Attach the Magnet to the door or window frame at the same level as the
Sensor.
ATTENTION! It is required to install the Sensor and the Magnet in such a way
that concave parts of their bodies are next to each other (See Figure 5-a below).

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1
Page 17 of 38
5-a –Correct positioning
(orientation)
5-b - Incorrect positioning
(orientation)
5-c - Correct positioning
(aligning)
5-d - Incorrect positioning
(aligning)
5-e - Correct positioning
(distance)
5-f - Incorrect positioning
(distance)
Figure 5 –Installation rules for the Sensor and the Magnet
NOTE. The Sensor and the Magnet shall be mounted coaxially so that in the closed
position of the door or the window the Magnet is at a distance of no more than
2cm from the Sensor.
Concave parts
are next to
each other
Concave parts
are apart
> 2 cm

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved
Page 18 of 38
NOTE. The Sensor may be installed using the screw (supplied).
To align the position of the Sensor and the Magnet (when the door frame is thicker
than the door leaf), the User may use the 3M Sponge supplied with the device.
To clean the Sensor, use a soft cloth with a small amount of water or alcohol.
Cleaning can only be performed after switching off the Sensor.
3. Switch on the Door & Window Sensor by removing the battery isolation film.
4. Install the Sensor onto the removable cover in the selected location.
NOTE. If the LED starts flashing slowly after removal of the battery isolation film,
you can immediately begin connecting it to the Control Gateway/IoT Router and
skip Step d of par. C. “CONNECTION TO THE CONTROL GATEWAY/IOT ROUTER”.
After the above Steps 1-4 are successfully completed, the Door & Window Sensor is
considered to be installed and ready for operation.
B. LOGIN TO THE EXISTING USER ACCOUNT
a. Enter your e-mail address and password in the login
screen.
b. Click on the LOG IN button.
NOTE. If the password was lost, the User can restore it by
clicking on a corresponding link on the screen.
To restore a forgotten password, use the e-mail address
linked to your User Account, to which instructions on
changing the password will be sent.

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
©Perenio IoT spol s r.o. All rights reserved Doc Version: 2.4.1
Page 19 of 38
C. CONNECTION TO THE CONTROL GATEWAY/IOT ROUTER
a. Click on the “+” icon in the upper right corner of the
Devices tab and select the sensor;
b. Select the Control Gateway/IoT Router to which the
Sensor shall be connected (This screen will be
displayed, only if there are several Control
Gateways/IoT Routers activated in the User Account).
NOTE. The Control Gateway/IoT Router must be
connected to the mains and the Internet, as well as
activated in the Perenio Smart App.
c. Start searching for Sensors;
d. If the LED flashes slowly after the first power on of
the device, proceed to the Step e, otherwise press
and hold the reset button as shown in the picture
above until the LED Indicator starts blinking.
NOTE. Several sensors may be connected to the Control
Gateway/IoT Router at once.
e. After successful connection, enter the Sensor’s name
and select the Room.
С.1. CONNECTION ERRORS
The connection failure of the device may occur due to one
of the following reasons:
a. The device is switched off or at a too long distance from
the Control Gateway/IoT Router (4.5 meters);
b. The Control Gateway/IoT Router is offline;
c. The LED Indicator was blinking fast before start of the
sensor connection (You should remove the sensor
battery and insert it back into the casing).
NOTE. To eliminate connection failures, follow instructions
specified on corresponding screens of the smartphone.

Installation and Operation Manual for Perenio®
PECWS01 Door & Window Sensor
Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All rights reserved
Page 20 of 38
The entire process of the Sensor connection in the Mobile App is shown below.
1
2
3
4
5
6
7
8
9
10
11
12
Figure 6 –Add new device (Sensor) procedure