Performance Tool W54207 User manual

Commercial
Grease Gun
OWNER’S MANUAL
Stock Number W54207
FOR YOUR SAFETY,
please read these instructions carefully and retain them for future use.
Other Grease Guns
and Accessories
from Performance Tool
Mini Grease Gun W54200
Lever Action Grease Gun W54201
Professional Grease Gun W54202
Economy Grease Gun W54203
Pistol Grip Grease Gun W54204
Suction Gun W54220
12” Grease Gun Flex Hose W54210
18” Grease Gun Flex Hose W54211
Grease Gun Coupler W54212
Grease Injector Needle W54213
LIMITED WARRANTY
PERFORMANCE TOOL extends only the following warranties, and only to original retail purchasers. These warranties give
specific legal rights. Except where prohibited by local law, the law of the State of Washington governs all warranties and all
exclusions and limitations of warranties and remedies. There may be other rights which vary from state to state.
PERFORMANCE TOOL warrants the product to be free from defects in materials and workmanship under normal use and
service. A defective product may be returned for a free replacement within 90 days from the date of purchase, provided that
product is returned to place of purchase immediately after discovery of defect. These warranties shall be valid only when a sales
receipt showing the date of purchase accompanies the defective product being returned.
These warranties exclude blades, bits, punches, dies, bulbs, fuses, hoses, and other consumables which must be replaced under
normal use and service. These warranties shall not apply to any product or part which is used for a purpose for which it is not
designed, or which has been repaired or altered in any way so as to affect adversely its performance or reliability, nor shall these
warranties apply to any product or part which has been subject to misuse, neglect, accident or wear and tear incident to normal
use and service.
PERFORMANCE TOOL does not authorize any other person to make any warranty or to assume any liability in connection with
its products.
Except for warranties of title and the limited express warranties set forth above, PERFORMANCE TOOL makes no express or
implied warranties of any kind with respect to its products. In particular, PERFORMANCE TOOL makes no implied warranty
of merchantability and no implied warranty of fitness for any particular purpose, except that for goods purchased primarily for
personal, family or household use and not for commercial or business use, PERFORMANCE TOOL makes an implied warranty
of merchantability (and, if otherwise applicable, an implied warranty of fitness for a particular purpose), but only for the particular
qualities or characteristics, and for the duration, expressly warranted above. The laws on limitation of implied warranties may
differ from state to state, so the above limitations may not apply in all cases.
PERFORMANCE TOOL shall not be liable for consequential, incidental or special damages resulting from or in any manner
related to any product, or to the design, use, or any inability to use the product. The sole and exclusive remedy for a defective
product or part shall be the repair, or replacement thereof as provided above. The laws on limitation of remedies or on
consequential, incidental or special damages may vary from state to state, so the above limitations may not apply in all cases.
Copyright © 2011 PERFORMANCE TOOL – All rights reserved

NOTE - Used cartridges must be removed prior to suction filling.
1. Remove the gun head cap from the barrel.
2. Submerge open end of the barrel into grease bucket. Be sure the plunger
handle is depressed completely. Grasp the barrel firmly and pull back slowly on
the plunger handle. Be sure the mouth of the barrel is always under the surface
so that air is not transferred into the barrel. (Figure 6)
3. Loading is complete when plunger rod is fully
extended.
4. Reattach the gun head cap to the barrel. Depress
lock release and push the plunger rod back into the
gun.
NOTE - Grease guns may lose their prime on
occasion, because of air pockets in the grease. If this
occurs, remove the trapped air by bleeding the head
cap and resume pumping.
NOTE - This is a basic instruction manual which covers various models of
grease guns. The illustrations below may not depict exactly your specific gun.
1. Rotating counter clockwise, unscrew Head Cap from gun Barrel. (Figure 1)
GREASE CARTRIDGE LOADING
NOTE - Because they lack lubrication on the rubber plunger, new grease guns
may be difficult to load with grease cartridges the first time. Apply a liberal
coating of grease to plunger when using gun for the first time. This grease gun
requires a 14 oz. grease cartridge.
2. Draw handle back fully so that the
plunger rod catches and locks into place.
(Figure 2)
CAUTION: Depressing the lock release when
empty causes the handle to snap back quickly.
3. After removing the plastic cap from the grease cartridge, apply a small amount
of grease to the inside edge of the cartridge. This will make insertion of the
plunger easier. (Figure 3)
4. Push grease cartridge into gun barrel completely, until metal edge tightly seals
on top of the grease gun barrel. Detach flip-top seal from cartridge. (Figure 4)
5. Screw on head cap approximately two turns, being sure not to tighten.
Release plunger rod from its locked position and push in. Push on plunger
rod handle to force plunger into cartridge. At the same time, pump the lever or
handle to release trapped air. When grease comes through vents and the head
of the gun, fully tighten the head cap to the barrel.
6. As soon as the gun is pumping grease, carefully depress the lock release and
push plunger rod back into gun.
DO NOT REFILL
USED CARTRIDGES
WARN I NG !
Figure 6
Figure 4
Flip-top Tab
SUCTION FILLING
Figure 2
Plunger
Handle
Lock
Release
Figure 3
Barrel
Plastic Cap
Grease Cartridge
Figure 1
Head Cap
Barrel
Bleeder Valve