PerkinElmer Lambda 365 User manual

09931256D
PerkinElmer, 710 Bridgeport Avenue,
Shelton, CT 06484-4794, U.S.A
Produced in the USA.
Lambda 365 Microcell Holder
Installation Instructions
This instruction sheet describes the installation of this accessory which is used with the Lambda 365
Spectrophotometer.
NOTE:
Read these instructions before you install this accessory.
Contacting PerkinElmer
Supplies, replacement parts, and accessories can be ordered directly from PerkinElmer, using the part
numbers.
See our website:
http://perkinelmer.com
PerkinElmer's catalog service offers a full selection of high-quality supplies.
To place an order for supplies and many replacement parts, request a free catalog, or ask for information:
If you are located within the U.S., call toll free 1-800-762-4000, 8 a.m. to 8 p.m. EST. Your order will be
shipped promptly, usually within 24 hours.
If you are located outside of the U.S., call your local PerkinElmer sales or service office.
Features
•Suitable size for micro cells
•Excellent durability
•Adjustable cell holder position
Figure 1 Lambda 365 Micro Cell Holder [P/N: N4101028]

09931256D
2
Dimensions and Specifications
Type Specification
Outline
Height (mm) 86.5
Width (mm) 120
Depth (mm) 170
Weight (kg) 0.56
Description
Connectable Cells
Other Cells are available upon request if what you want is not listed.
Configuration of Micro Cell Holder
Figure 2 Lambda 365 Micro Cell Holder Configuration
Figure 3 Knob
Description
Micro cell, 10 mm light path, Quartz, 1400 ㎕, ea
Micro cell, 10 mm light path, Quartz, 700 ㎕, ea
Micro cell, 10 mm light path, Quartz, 50㎕, ea
Right-to-left
adjustment knob
Top-to-bottom
adjustment knob

09931256D
3
Installation
1. Loosen a knob to take apart the existing cell holder.
Figure 4 Loosening a knob
2. Pull out the existing cell holder by hand.
Figure 5 Pulling out the cell holder
3. Insert the micro cell holder in the sample compartment and tighten the knob.
Figure 6 Inserting the Micro Cell Holder

09931256D
4
4. Insert the micro cells into the cell holder.
Figure 7 Inserting the micro cells into the cell holder
How to adjust the Microcell holder so that the beam passes
through the micro cell window
1. Run Scan mode and select Method. Select SBW 20.
2. Select Measure in main menu and select Go to Wavelength and then check Zero Order.
3. Input the micro cells into each reference and sample holder.
Reference
Sample

09931256D
5
4. Attach the white paper (ex. post-it note) on the right side wall of the sample compartment for
checking the light passes through the window of the micro cell. In order to adjust the right-and -
left position of the micro cell holder, loosen the two hand bolts on the plate of the microcell
holder.
5. Adjust the position by moving the micro cell holder back and forth slowly so that the large
portion of light passes through the window of the micro cell. After the position adjustment is
completed, tighten the hand bolt on the bottom plate of the microcell holder.

09931256D
6
6. In order to adjust the height of the micro cell holder, loosen the knob on the side of the
microcell holder.
7. Adjust the height by moving the micro cell holder up and down slowly so that the large portion
of light passes through the window of the micro cell. After the height adjustment is completed,
tighten the knob on the side of the micro cell holder.
NOTE:
It is required to adjust the left-and-right and height positions of both the sample and reference
cell holder.