Perlesmith PSLFK3-24 User manual

PSLFK3-24
V1.0
LARGE FULL-MOTION TV WALL MOUNT
Thank you for choosing our product! We strive to provide the best quality and
services for our customers. Would you kindly share your experience on Amazon if
\RXDUHVDWLVƉHG"6KRXOG\RXKDYHDQ\LVVXHVSOHDVHGRQWKHVLWDWHWRFRQWDFWXV
7HOHSKRQHғ0RQ)ULDPSP36786$
(PDLOғVXSSRUWXV#SHUOHVPLWKFRP86&$'(8.)5,7(6-3$8
English ------------------------ 1-10
Deutsch ------------------------ 11-20
Français------------------------ 21-30
Español ------------------------ 31-40
Italiano ------------------------ 41-50

Tools Needed
Hammer
P1
Getting Started
WARNING:
Exceeding the weight capacity can result in serious personal injury or damage to
equipment! It is the installer’s responsibility to make sure the weight of the TV (with
accessories) does not exceed 60 kg.
WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER
INSTALLATION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.
If you do not understand the instructions or have any concerns or questions, please contact a
qualified installer.
Do not install or assemble if the product or hardware is damaged or missing. Not all parts and
hardware included must be used. If you require replacement parts, contact customer service at
VXSSRUWXV#SHUOHVPLWKFRP
This product has been designed for use on a vertical wall constructed of wood studs. Wood studs
being defined as a wall consisting of a minimum of 2” x 4” studs with a maximum of 16” stud
spacing with a maximum of 1/2” of wall covering (drywall, lath, plaster).For custom installations
please contact a qualified installer. For safe installation, the wall you are mounting to must support
4 times the weight of the total load. If not, the surface must be reinforced to meet this standard.
The installer is responsible for verifying that the wall structure/surface will safely support the total
load.
This product may contain moving parts. Use with caution.
DO NOT EXCEED THE MAXIMUM WEIGHT CAPACITY FOR THIS PRODUCT.
Please check www.perlesmith.com for more products and company information.
Stud
Finder
Tape
measure
1/2 in.
(12.7 mm)
7/32 in.
(5.5 mm)
Wood Drill
Screw
driver
Pencil Level
(included
inside the box)
Drill 3/8 in.
(10 mm)
Concrete Drill
CAUTION!
!60 kg
MAXIMUM WEIGHT CAPACITY

P2
Arm and
Wall Plate TV Brackets
Arm Extensions
Hardware Included
01 x1
03 x2
Front Support
End Caps
02 x1
05 x1
04 x2
Hardware （Wall /Product)
5/16 x 2½ in
Lag Bolts
x4
Wall
Anchor
x4
DA
Washers
Ø8mm
Allen Wrench
x4
B
This product contains
small items that could be a choking hazard if
swallowed. Before starting assembly, verify
all parts are included and undamaged. If
any parts are missing or damaged, do not
return the damaged item to your dealer;
please contact our customer service team.
Never use damaged parts!
NOTE: Not all parts and hardware included
will be used.
WARNING:
Philips Screws
M6 x 15mm
M6 x 30mm
Philips
Screws
M6 x 50mm
Washers
Ø6mm
M4-5-6
Spacers
L10mm
x4x4
Philips Screws
M8 x 15mm
M8 x 45mm
x4
x4 x8 x4
M-DM-A M-B
x4
M-C M-E
Philips
Screws
M8 x 65mm
x4
M-F M-G M-H
Spacers
L5mm
x8
M-I
TV Screws / Washers
x1
C
Hardware
M8
Nuts
x8
E
Washers
Ø8mm
x8
F
（product)
Wall Extension A
6A x2
Wall Extension B
6B x2

STEP 1-1 Select TV Screw Diameter
STEP 1-2 Select TV
Screw Length
P3
Thread screws by hand into the threaded holes on the back of your TV to select which screw
diameter fits your TV.
Correct Correct
Too Long
Too Short
Measurement
200mm~600mm
（7.9”~23.6”）
100mm~400mm
（3.9”~15.7”）
?
?
M6 M8

P4
STEP 1-3 Attach the TV Bracket
(a) Flat Back
04
Position your TV brackets over your TV hole pattern - making sure the brackets are centered
and level over the TV hole pattern.
Secure thebrackets using your screw/washer/spacer selection:
(a) for Flat Back
(b) for Round Back / Extra space
CAUTION: Ensure TV bracket is securely fastened before moving on to the next step.
04
(b) Round Back /
Extra Space
M-A M-D
M-H
M-B M-C
M-E
M-F
M-H
M-G M-I

STEP 2A
Wall Plate Installation (Wood stud)
P5
2A-1 Attach the Extensions to the wall plate
the wall plate extensions can be moved
0.6”(15mm) for both side if necessary.
only one side need to attach each of
extensions A and B
For 18”(457mm) to 24”(610mm) space studs
For studs with the sapce between
16.5“(420mm) to 18”(457mm)
6A
6B
0.6 Zoll
0.6 Zoll
0.6 Zoll
0.6 Zoll
6B
6B
6A 6A
01
FE
CAUTION:
CAUTION: Avoid potential personal injury or property damage! All lag bolts A
MUST BE firmly tightened to prevent unwanted movement of the wall plate 01 .
CAUTION: Ensure the wall plate is securely fastened to the wall before continuing
on to the next step.
ƕDrywall covering the wall must not exceed 5/8 in. (16 mm)
ƕMinimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
2A-2 Locate your studs. Verify and
mark the center of the studs by
finding the stud edges using an
awl, a thin nail, or an
edge-to-edge stud finder.
16”~24”
(406mm ~ 610mm)

P6
2A-3 Drill 4 pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
Make sure the depth is not less than 2 3/4” (70mm).
7/32 in.
Ø5.5 mm
in. (70 mm)
Configure A For 24”(610mm)
space studs
Configure B For 18” (457mm)
space studs
Configure C For 16.5” (420mm)
to 18”(457mm) space studs
Mount wall plate using 4 sets of 5/16 lag bolts (a) and washers B with a
1/2 in. socket wrench (not included).
A
B
2A-4
2A-2 Use wall plate to mark
mounting location x4 locations
for 24”(420mm)space
studs.
Mark the 4 inside holes for
18”(457mm)space studs
Holes pattern for
16.5”(420mm) to 18”
(457mm) space studs. Only
one sied need to install the Wall
Extension
OPT A OPT B OPT C
01
01
left
right
01
01
01
01
01
left
right
01
01
01
2
B A

STEP 2B
Wall Plate Installation (Concrete or brick, No need wall extensions 06A and 06B )
CAUTION: Avoid potential personal injury or property damage! All lag bolts A
MUST BE firmly tightened to prevent unwanted movement of the wall plate 01 .
CAUTION: Ensure the wall plate is securely fastened to the wall before continuing
on to the next step.
Drill pilot
holes
2B-2
2B-3
01
AB
D
Concrete Wall
Concrete Wall
D
01 A
DB
01
Install wall plate using lag bolts
and washer and anchor .
Tighten the lag bolts until they are
pulled firmly against the wall plate .
A
P7
2.75in 70 mm
Ø 10 mm
Ø 10 mm
2B-1
01
Position the
wall plate
at your
desired
height , level
the wall plate
and mark the
pilot hole
locations.
01
UP

STEP 3
Install Front support and extensions and End cap together.
Install the extensions [03] to Front support [02] with the pre-assembled screws.
Install the extensions [03] to Front support [02] withe the pre-assembled screws.
P8
B
3-1
3-2
Pre-assembled scews
Pre-assembled scews
Finished
02
03
05

P9
3-3
STEP 4
Hang TV with brackets [04] onto the arm extensions [02] and [03].
S1
Hang 02 onto 01 and using a screwdriver, secure with preassembled screws
S1
S1
S2 S2
01
02
04
03 02
Remove the
preassembled
screws [S2] and
save to use, then
raise the safety
locks.
Press the safety locks
then fasten the removed
screws [S2].