Perlesmith PSTVS04 User manual

Model: PSTVS04
Table Top TV Stand Instruction Manual
V4.0
Thank you for choosing this PERLESMITH product! At PERLESMITH we strive to
provide you with the best quality products and services in the industry. Should
you have any issues, please don't hesitate to contact us at
Technical Support:
1-800-556-6806 Mon-Fri 8am - 8pm(CST)
Other Info:
[email protected](US)
[email protected](CA)

P1
Want to watch a video that
show how to install the TV
brackets.
WE’RE HERE TO HELP
Want to watch a video that
show how to add the safety
locks.
Watch it now at:
https://youtu.be/kC4JmnNCDwM
Watch it now at:
https://youtu.be/MYjAmxcl1go
IMPORTANT SAFETY INFORMATION
Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact
our customer service at [email protected] (US)/
[email protected] (CA).
CAUTION: Avoid potential personal injuries and property damage!
Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.

P2
Wrench
Check the VESA Pattern of TV before the Installation
Minimum VESA pattern: 100mm/4 in(W)x100mm/4 in(H)
If your TV VESA is greater than 400x400 mm/16x16 in or less than
VESA 100x100mm/4x4in, this TV stand is NOT compatible.
If this TV stand is NOT compatible, please contact customer service
at [email protected] (US)/ [email protected] (CA)
to find a compatible product.
MAX: 400mm/16 in
MAX: 400mm/16 in
100 mm ≈ 4 in
200 mm ≈ 7 7/8 in
300 mm ≈ 11 3/4 in
400 mm ≈ 15 3/4 in
Tools Needed (Not lncluded)
Phillips Screwdriver
Weight Restrictions
If your TV weighs more, this
TV stand is NOT compatible.
88lbs/
40kg
DO NOT exceed the maximum weight
indicated. This TV stand is intended for use
only within the maximum weights indicated.
Use with products heavier than the maximum
weights indicated may result in failure of the
TV stand and its accessories, causing
possible damage and or injury.
WARNING

P3
(P) x1
Support Pillar
(Z) x1
Top Cover
(W) x4
Foot Pad
(R) x1
Gasket with
3 Holes
(Y) x1
Plastic Cover
(M) x1
TV Plate
(Q) x4
M6 Nut
(S) x4
M6x40mm
Bolt (T) x4
D6.5 Washer
WARNING: This product contains small items that could be a choking
hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. lf you require replacement parts, contact our
customer service at [email protected] (US)/
[email protected] (CA).
• Please note: Not all hardware included in this package will be used.
(O) x1
Tempered Glass Base
Supplied Parts and Hardware
Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware for Step 2
Note: The bolt is
shown in accordance
with the actual size
Note: The bolt is shown in
accordance with the actual size
(L) x3
M6x25mm Bolt
(V) x1
5/32in (4mm)
Allen Key
(V) x1
5/32in (4mm)
Allen Key

P4
(A) x4
M4x30mm
Bolt
(B) x4
M6x15mm
Bolt
(C) x4
M6x35mm
Bolt
(D) x4
M8x20mm
Bolt
(E) x4
M8x35mm
Bolt
(F) x4
M8x50mm
Bolt
(G) x4
Washer
(K) x2
Wire Clip
(H) x8
φ8.5x18x2.5mm
Spacer
(I) x4
φ8.5x18x10mm
Spacer
(J) x4
φ8.5x18x22mm
Spacer
(N) x2
TV Bracket
Note: The bolts and spacers are shown in accordance with the actual size
Supplied Part for Step 3
Supplied Parts and Hardware for Step 4

P5
Place foot pads [W] to the frosted side of the tempered glass
base [O] in the corners
Step 1-1
Connect the support pillar [P] to tempered glass base [O]
Step 1-2
Note: Make sure the
side with the wire clip
holes on the support
pillar faces the back
of the stand
Note: The paper
side of the gasket
with 3 holes [R]
should be touched
the tempered glass
base [O]
Attach the top cover [Z] to the support pillar [P]
Secure the support pillar [P] to tempered glass base [O] using plastic cover
[Y], gasket with 3 holes [R], bolts [L] and Allen key [V]
(K1) x2
Safety Lock
Note: You may need
assistance with this step.
Supplied Part and Hardware for Step 5
Step 1 Assemble the Base
O
W
R
OY
P
Z
L
V
O
V
LR
Table
P
Front Side
Back Side

P6
[Not Included]
Step 2 Connect the TV Plate [M] to Support Pillar [P]
Q
P
T
M
S
V
Front
Back
Note: There are three choices for
height adjustment. You can choose
your desired height position while
connecting the TV plate [M] to
support pillar [P]
Connect TV plate [M] to support pillar [P] using
bolts [S], washers [T] and nuts [Q]
Note: Connect the TV plate [M] to the front
side of the support pillar [P] with the bump of
the TV plate facing back side of the stand.
The First Choice
The First Choice
The Second Choice
The Second Choice
The Third Choice
The Third Choice
Note: You may need assistance
with this step.

P7
Only one bolt size fits your TV.
Select TV Bolts
Step 3 Secure the Wire Clips [K] to Support Pillar [P]
Step 4 Secure the TV Brackets [N] to TV
P
K
Too Long
Correct Correct
Too Short
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers
combination. We recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
Please Note: The provided TV bolts meet most of today’s TVs design. However, some
TVs require special bolts which may not be in the hardware bag. In this case we offer
our “PSUHP" Universal Hardware Kit which provides a large selection of bolts that
can meet the demand of older and unique applications.
Please Note: When using the spacers it is important to note that they can be used in
multi-layers (meaning stacked). If you have any difficulty
understanding how to install the TV bolts or spacers, please contact
customer service at [email protected] (US)/
[email protected] (CA).
M4 M6 M8

P8
Option B (For Round Back TV)
Option A (For Flat Back TV )
G
A/B/D
H/I
(If needed)
G
A/C/E/F
H/I/J
N
Alternate Spacer
Setups
Note: Keep
the arrow up
Note: Keep
the arrow up
Alternate
Spacer
Setups
CAUTION: Ensure the TV brackets
[N] are EQUALLY CENTERED on your
TV and securely fastened in place.
Please note: The bolt hole locations
on your TV may vary in accordance of
the manufacturers design of the TV. We
are only illustrating possible locations
of the bolt holes.

P9
Alternate Spacer
Setups
Alternate Spacer
Setups
Option D
For cable interference or inset holes, use spacers [H], [I] and [J] to create
extra space between the TV and TV brackets
Spacers may be necessary for 2 holes ONLY.
Option C (For TV with A “Bump”)
G
A/C/E/F
H/I/J
A/B/D
G
H/I
(If needed)
A/ C/ E/ F
H/ I/ J
G
N
N
Note: Keep
the arrow up
Alternate
Spacer
Setups

P10
①
②
Note: Please note, there is
no bolt holes in the TV plate
TV brackets are two-height-adjustable.
You can choose the proper height.
Step 5-1 Hang the TV with brackets to the TV plate
Step 5-2 Push the bottom of the TV to TV plate
Step 5-3 Insert the safety locks [K1] into the upward facing hooks at the
midway to lower part of the TV bracket. Please note this is where the lower
part of the TV bracket meets the TV plate. Then tighten the bolts of the
safety lock [K1] until the bolts touch the TV plate.
Step 5 Attach TV to the TV Plate [M] and Manage the Wires
The First Choice
The Second Choice
K1
“Be gentle”
③
HEAVY! You may need
assistance with this step.

Thank you again for choosing
this PERLESMITH product!
All of us at PERLESMITH do appreciate your product purchase. We hope that you
are as happy with your product as we designing and manufacturing it for you. We
strive to provide you with the best quality products and services in the industry. If
you have any questions please don't hesitate to contact us at
Technical Support:
1-800-556-6806 Mon-Fri 8am - 8pm(CST)
Other Info:
[email protected](US)
[email protected](CA)