Perlesmith PSTVS02 User manual

6
SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER
INSTALLATION OR ASSEMBLY. READ FOLLOWING WARNINGS BEFORE BEGINNING.
•If you do not understand the instructions or have any concerns or questions, please contact customer
service at [email protected]
•Do not install or assemble if the product or hardware is damaged or missing.
•Not all parts and hardware included will be used. lf you require replacement parts, contact customer
service at [email protected]
•This product may contain moving parts. Use with caution.
•Please check www.perlesmith.com for more products and company information.
•Exceeding the weight capacity can result in serious personal injury or damage to equipment! lt is the
installers’ responsibility to make sure the combined weight of the product and the TV does not exceed
maximum weight. Use with heavier televisions may result in instability, causing tip over or resulting in
death or serious injury!
IMPORTANT SAFETY INFORMATION
Attach Vertcal TV Brackets
Ensure that your TV Brackets ④ are level and centered on the back of
the TV.
Install using the TV screw/washer/spacer configuration you selected for
your TV.
CAUTION: Avoid potential personal injuries and property damage! DO
NOT use power tools for this step.Tighten the TV screws only enough to
secure the TV brackets ④ to the TV .
DO NOT over-tighten the TV screws.
Secure TV onto TV Plate
Hang the TV(with the brackets ④) on TV Plate ③
and adjust the height. Then use the screwdriver
to lock the buckle ⑤ tight.
Swivel to the desired angle.
Supplied Parts and Hardware
Glass Base TV Pillar TV Plate
TV Bracket Buckle Covering plate
Parts and Hardware
Rubber foot Plastic plate M8*25mm M6*12mm
D8 washer 4mm 5mm
M6x15mm
M8x25mm
M8x35mm
M8x50mm
D6 Washer
2.5mm Spacer
10mm Spacer
22mm Spacer
S1
S2
S3
S4
S5
S6
S7
S8
S9
M6x35mm
S6
S1/S2
S7/S8/S9
S3/S4/S5
S7/S8/S9 Alternate
Spacer
Setups

Attach the pillar to the base.
Attach the pillar ② to the base ① using C and E .
Remember to place the plastic plate B in between the
pillar ② and base ①.
Next, tighten the screws using the hex key G .
Use 2 sets of Dand hex key Fto tighten the right
part ③ and ⑥ together, fasten four screws again to
make sure they are tight.
Attach the parts ③ and ⑥
to ②
Put the 2 plates ③ next
to each other on top of
the pillar in line with the
screw holes.
Next, place the covering
plate ⑥ with the LOGO
facing upwards on top of
the plates ③ in line with
the screw holes.
Use 2 sets of Dand hex
key Fto tighten the left
part ③ and ⑥ together.
Screw the four screws D to the pillar ② using the hex key F.
Before mounting the TV, adjust the pillar to the desired height.
6
6
6
Place foot pads A on the bottom of the base ① in the corners.
M4mm
Note:The 3 screws to connect the
base ① and the pillar ② MUST be
firmly tightened.
Height adjustment
according to the size
of your TV.
Select TV Screws Diameter
Hand thread TV screws into
the threaded inserts on the
back of your TV to
determine which screw
diameter(M6 or M8)to use.
Select TV Screw diameter.
Select TV Screw Length
If your TV has a flat back, use the shorter TV screws.
Spacers and longer TV screws are supplied to accommodate:
irregular/round back TVs, TVs with inset munting holes,
Extra space needed for cables
FLAT BACK ROUND BACK INSET HOLES CABLES
CAUTLON:
Verify adequate thread
engagement with the screw or
screw/spacer combination.
-Too short will not hold the TV.
-Too long will damage the TV.
Too short
Correct
Too Long