Perlesmith PSLFK1 User manual

TV Bracket
Arm Extensions 03 x2
Front Support 02 x1
04 x2
LARGE FULL-MOTION TV WALL MOUNT
for most 37" to 70" TVs
up to 132 lbs
PSLFK1
*
*
*
*
*
*
*
Stud
Finder
Tape
measure
Pencil Level Drill 1/2 in.
(12.7 mm)
7/32 in.
(5.5 mm)
Wood Drill
Tools Needed
Screw
driver Hammer
(included
inside the box)
WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER INSTALLATION OR
ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.
If you do not understand the instructions or have any concerns or questions, please contact a qualified installer.
Do not install or assemble if the product or hardware is damaged or missing. Not all parts and hardware included must be used. If you
require replacement parts, contact customer service at [email protected].
This product has been designed for use on a vertical wall constructed of wood studs. Wood studs being defined as a wall consisting of a
minimum of 2” x 4” studs with a maximum of 16” stud spacing with a maximum of 1/2” of wall covering (drywall, lath, plaster).For custom
installations please contact a qualified installer. For safe installation, the wall you are mounting to must support 4 times the weight of the
total load. If not, the surface must be reinforced to meet this standard. The installer is responsible for verifying that the wall structure/sur-
face will safely support the total load.
This product may contain moving parts. Use with caution.
DO NOT EXCEED THE MAXIMUM WEIGHT CAPACITY FOR THIS PRODUCT.
Please check www.perlesmith.com for more products and company information.
CAUTION!
55””””
MAXIMUM SCREEN SIZE MAXIMUM WEIGHT CAPACITY
WARNING!
WEIGHT CAPACITY
!
70”
60 kg
132 lbs
Hardware Included
Hardware （Wall )
5/16 x 2½ in
Lag Bolts
x4
A
Washers
Ø8mm
x4
B
TV Screws / Washers
Philips Screws
M6 x 15mm
M6 x 30mm
Philips Screws
M4 x 12mm
M4 x 30mm
Philips Screws
M5 x 12mm
M5 x 30mm
Washers
Ø6mm
M4-5-6
Spacers
L10mm
x4
x4 x4 x4 x4x4
Philips Screws
M8 x 15mm
M8 x 30mm
x4
x4 x4 x4
M-G M-H M-I M-J
Spacers
L5mm
x8
M-K
M-E
M-J
M-G
M-CM-A
04
04
04
M-F
M-J
M-I
M-K
M-B
M-D
04
M-H
STEP 1
Measure the distance between the holes
located at the back of your TV (these
measures may form the shape of a square, or
a rectangle) and check that these taken
measures are within the VESA(*) range for this
wall mount.
(*) VESA: International standard established
by the TV manufacturers used to determine if
LCD / LED TVs are compatible with wall
mounts.
75 mm ≈2 7/8 in
100 mm ≈4 in
200 mm ≈7 7/8 in
300 mm ≈11 3/4 in
400 mm ≈15 3/4 in
600 mm ≈23 5/8 in
STEP 2 Install TV bracket
Check the VESA pattern of your TV
400mm (15 3/4 in)
Max 600mm（23 5/8 in）
Max
STEP 2A
Flat back TV (Universal monitor plate)
STEP 2B
Connect TV Brackets to back of TV
Connect TV brackets to back of TV
Arm and
Wall Plate 01 x1
USE WITH PRODUCTS LARGER THAN THE MAXIMUM WEIGHT AND SIZE MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY.
USER MUST REMOVE TELEVISION OR OBJECT OFF THE BRACKET BEFORE ADJUSTING. NOT SUITABLE FOR A TV THAT
SURPASSES THE TELEVISION MAXIMUM WEIGHT CAPACITY AND RECOMMENDED DIAGONAL MEASURED TV SIZE!
1 2
3 4 5
Check TV screws
Please select the proper screw length for your TV by hand tightening to check your plat panel thread depth.
Correct Correct
Too Long
Too Short
V2
Round back TV (Universal monitor plate)

03
S4
3-1
3-2
01
To adjust the tilt in both sides, loosen both tilt levers and move panel to desired position.
Tighten both tilt levers to hold desired tilt.
TIGHTEN
！
TIGHTEN
！
LOOSEN
Made in China
PERLE ELECTRONICS HARDWARE (HONGKONG) CO., LIMITED • FLAT B07, 23/F HOVER IND BLDG NO.
26-38 KWAI CHEONG RD •
Any questions please contact : [email protected]
Please check www.perlesmith.com for more products and company information.
STEP 3 Wall Plate Install
Use a stud finder (not included) to locate wood
studs. Mark the edge and center locations.
Use wall plate [01] to mark
mounting location x4 locations
Center line
01
CAUTION: Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
!
Ensure that marked at the
center of thestud.
If needed, the TV can be leveled +/-3 degrees.
Loosen 2 screws [S1]
S1 Tighten 2 screws [S1]
S1
Level the TV
± 3°
3-3
3-4
01
2
STEP 4
Insert the extensions into the
03 02
4-2
4-1
02
03
4-3
Fasten the Screws x4 removed from
extensions .
Drill 4 pilot holes using a 7/32 in. (5.5 mm)
diameter drill bit. Make sure the depth is
not less than 2 3/4” (70mm).
Mount wall plate [03] using 4 sets of 5/16 lag bolts (a)
and washers B with a 1/2 in. socket wrench (not
included).
01
A
B
7/32 in.
Ø5.5 mm
in. (70 mm)
S4
S4
4-4 S1
S2
Hang 02 and 03 onto 01, and using Screwdriver secure with pre-assembled screws
and washer .
S2
S1
S1
S2
01
02
Screw
driver
STEP 6
Secure TV with brackets
against the arm extensions
and with the pre-assem-
bled screws [S3]
04
03
02
[S3]
04
04
STEP 5 STEP 7 Tilt adjustment STEP 8 Level adjustment
Hang TV with brackets
04
onto the
arm extensions
02
and
03
.
03
04
B
A
Install arm extensions then fasten it
6 7 8
9 10 11
Hang TV
Secure TV
UP
02
Remove the pre-assembed screws from the
extensions and save them to use.
03
03
S4
S4