Petsafe Deluxe In-Ground Radio Fence Setup guide

PetSafe®Deluxe
In-Ground Radio Fence™
Operating and Training Guide
Please read this entire guide before beginning
BATTERY 6V
RFA-67

2 1-800-732-2677
Thank you for choosing PetSafe®, the #1 selling brand of electronic training solutions in the world. Our
mission is to ensure your pet’s safety by providing you the tools and techniques to successfully train
your pet. If you have any questions, please contact the Customer Care Center at 1-800-732-2677 or
visit our website at www.petsafe.net.
___________________________________________
Table of Contents
Components ................................................................................................................................... 3
Other ItemsYou May Need.............................................................................................................. 3
How the System Works .................................................................................................................... 4
Key Definitions ............................................................................................................................... 4
Operating Guide
Locate the Fence Transmitter....................................................................................................... 5
Lay Out the System..................................................................................................................... 5
Sample Layouts........................................................................................................................... 6
Position the Boundary Wire ......................................................................................................... 7
Connect the Wires to the Fence Transmitter ................................................................................. 8
Prepare the Receiver Collar ......................................................................................................... 9
Set the Boundary Width and Test the Receiver Collar...................................................................10
Install the Boundary Wire ...........................................................................................................11
Place the Boundary Flags ...........................................................................................................13
Fit the Receiver Collar................................................................................................................13
Training Guide
Be Patient With Your Pet .............................................................................................................14
Day 1 - Boundary Flag Awareness...............................................................................................15
Days 2 thru 4 - Continue Boundary Flag Awareness ....................................................................15
Days 5 thru 8 - Distraction Phase ...............................................................................................16
Days 9 thru 14 - Unleashed Supervision......................................................................................16
Days 14 thru 30 - Pet Monitoring ...............................................................................................17
TakingYour Pet Out of the Pet Area ............................................................................................17
Accessories ....................................................................................................................................17
Troubleshooting.............................................................................................................................18
Short Loop Test .............................................................................................................................19
To Locate a Break in the Wire .........................................................................................................20
Terms of Use and Limitation of Liability .........................................................................................20
FCC ..............................................................................................................................................21
Caution .........................................................................................................................................21
Layout Grid ...................................................................................................................................23
Mounting Template ........................................................................................................................24

www.petsafe.net 3
Components
Boundary Flags - 50
Power
Adapter
Boundary Wire - 500 ft.
Wire Nuts
Test Light
Warranty
Card
Warranty
Long
Contact Points
Fence
Transmitter
Battery
(PetSafe®RFA-67)
Receiver
Collar w/Short
Contact Points
Operating and
Training Guide
Installation
and Training
Video CD
H
A
P
P
Y
O
W
N
E
R
S
S
A
F
E
P
E
T
S
Video CD
compatible with
most DVD players
and computer
CD-ROM drives
VHSTape
available through
our Customer
Care Center at
1-800-732-2677
Streaming Video
available at
www.petsafe.net
Installation and Training
Video CD
RFA-140
DELUXE
In-Ground
RADIO FENCE
™
Other Items You May Need
• Additional wire and flags (Part #PRFA-500)
• Tape measure
• Drill & mounting hardware
• Shovel or lawn edger
• Pliers
• Wire stripping pliers
• Scissors
• Lighter
• Electrical tape
• Additional wire nuts
• Ground rod and clamp
• Waterproofing compound (e.g. silicone caulk)
• PVC pipe or water hose
• Circular saw with masonry blade
• Patching compound
• Staple gun
• Non-metallic collar and leash
Note: For information on professional installation of your new PetSafe In-Ground Radio FenceTM, contact the Customer Care Center
at 1-800-732-2677 or visit our website at www.petsafeprofessional.com.

4 1-800-732-2677
How the System Works
The PetSafe In-Ground Radio FenceTM has been proven safe, comfortable, and effective for all pets over 8 pounds.The
system works by producing a radio signal from the Fence Transmitter through up to 4000 feet of Boundary Wire. The
Boundary Wire is buried or attached to a fixed object to enclose the Pet Area.You temporarily define the Pet Area with
Boundary Flags for a visual aid in training your pet.Your pet wears a Receiver Collar with Contact Points that touch his
neck, and, once trained, is allowed to roam freely in the Pet Area. When your pet reaches the Warning Zone, the Receiver
Collar gives a warning beep. If your pet continues into the Static Correction Zone, a safe Static Correction will be delivered
through the Contact Points to get his attention until he returns to the Pet Area.
Key Definitions
Fence Transmitter: The device that transmits the radio signal through the Boundary Wire.
Pet Area: The area within the Warning Zone where your pet can roam freely.
Warning Zone: The outer edge of the Pet Area where your pet’s Receiver Collar begins to beep, warning him not to go into
the Static Correction Zone.
Static Correction Zone: The zone beyond the Warning Zone where your pet’s Receiver Collar will emit a Static
Correction, signaling him to return to the Pet Area.
Boundary Width: The combination of the Warning Zone and the Static Correction Zone.
Receiver Collar: The device that receives the radio signal from the Boundary Wire.
Correction Level Button: The button to adjust the level of Static Correction your pet receives in the Static Correction Zone.
Receiver LED Indicator Light: The light that indicates the level of correction at which the Receiver Collar is set.This
light also serves as a low battery indicator.
Contact Points: The contacts through which the Receiver Collar delivers the safe Static Correction when your pet moves
into the Static Correction Zone.
Power Jack: The jack where the Power Adapter plugs into the Fence Transmitter.The Fence Transmitter is powered by a
standard 120-volt outlet.
Boundary Control Switch: The switch to adjust according to the length of Boundary Wire used.
Ground Terminal: The terminal where the Ground Wire connects to the Fence Transmitter.
Boundary Wire Terminals: The terminals where the Boundary Wires connect to the Fence Transmitter in order to
complete a continuous loop.
Loop Indicator Light: The light that indicates that the Boundary Wire makes a complete loop, enabling the signal to be
transmitted.
Boundary Width Control: The knob that adjusts the width of the Warning and Static Correction Zones. Note: Adjusting the
knob does not change the level of Static Correction on the Receiver Collar.
Pet Area
Static Correction
Zone
Static Correction
Zone
Fence
Transmitter
Warning
Zone
Warning
Zone
Boundary
Width
Correction Level Button
Battery
Contact Points
Receiver
LED
Indicator Light
Washers
Receiver Collar
}
Boundary Width
Control
Power Light
Loop Indicator Light
Boundary Wire
Terminals
Ground
Terminal
Boundary
Control
Switch
Power
Jack
Fence Transmitter

www.petsafe.net 5
Locate the Fence Transmitter
Place the Fence Transmitter:
• In a dry, well ventilated, protected area (1A, 1B).
• In an area where temperatures do not fall below freezing (e.g., garage, basement, shed, closet).
• Secured to a stationary surface using appropriate mounting hardware (not included). A mounting template is
included in the back of this guide.
• At least 3 feet from large metal objects or appliances as these items may interfere with the signal consistency (1C).
Once you have mounted the Fence Transmitter, the Boundary Wire must exit the building.This can be
accomplished via a window or through a 1/8” hole drilled through the wall. Ensure the drill path is clear of any
utilities. Make sure the Boundary Wire is not cut off or pinched by a window, door, or garage door, as this can
damage it over time.
To prevent fires and electrical hazards, install the Fence Transmitter in buildings that are in accordance with state
and local electrical codes.
1A 1B
3ft.
1C
__________________________________________________
Lay Out the System
Basic Planning Tips
•The Boundary Wire MUST start at
the Fence Transmitter and make a
continuous loop back (2A).
•Design a layout that is suitable for your
yard. Sample layouts are provided in
this section, and a grid for designing
your layout is provided in the back of
this guide.
•Always use gradual turns at the
corners to produce a more consistent
boundary (2B). Do not use sharp
turns, as this will cause gaps in your
boundary.
•Avoid making passageways too narrow
for your pet to move about freely (e.g.,
along the sides of a house).
• The Receiver Collar can be activated
2A 2B
inside the house if the Boundary Wire runs along the outside wall of the house. If this occurs, remove your
pet’s Receiver Collar before bringing him inside, decrease the range using the Boundary Width Control or
consider an alternative layout.
Operating Guide
Step
1
Step
2

6 1-800-732-2677
Sample Layouts
Sample 1:
Perimeter Loop
(Single Loop) The
Perimeter Loop is
the most common
layout. This will
allow your pet to
freely and safely
roam your entire
property (2C). It
can also protect
gardens, pools and
landscaping (2D).
D
E
A
C
B
Sample 2 (2E): Perimeter Loop Using Existing
Fence (Single Loop)
This layout allows you to include your existing fence
as part of your layout and keep your pet from jumping
out or digging under your existing fence. It reduces the
amount of wire which will need to be buried. From the
Fence Transmitter, run the wire to A, Ato B, Bto C, C
to D, Dto E, Eto A, twist the wires from Aback to the
Fence Transmitter. See the “Install the Boundary Wire”
section for more information on attaching the wire to a
fence.
Double Loop
A Double Loop must be used when you are not establishing the Boundary Zone on all sides of your property.
When using a Double Loop, the Boundary Wire must be separated by a minimum of THREE TO FIVE FEET to
avoid canceling the signal. Remember that a Double Loop will require twice as much wire.
E
F
BA
D
C
E
F
C
A
D
B
Sample 3 (2F): Front or Back
Yard Only (Double Loop)
From the Fence Transmitter, run
the wire to A, Ato B, Bto C, C
to D, Dto E, Eto F, make a U-
turn and follow your path all the
way back to A, keeping the wire
separated three to five feet. Twist
the wire from Aback to the Fence
Transmitter.
B
A
3-5'
Sample 4 (2G): Front
Boundary Only
(Double Loop)
From the Fence Transmitter,
run the wire to A, Ato B, B
back to Akeeping the wire
separated three to five feet.
Twist the wire from Aback to
the Fence Transmitter.
E
B
D
C
A
3-5'
Sample 5 (2H): Lake Access
(Double Loop)
From the Fence Transmitter,
run the wire to A, Ato B,
make a U-turn and go to C, C
to D, Dto E, make a U-turn
and follow your path all the
way back to Akeeping wire
separated three to five feet.
Twist the wire from Aback to
the Fence Transmitter.

www.petsafe.net 7
Sample 6 (2J): Wire Loop Attached to Existing Fence (Double Loop)
This layout allows you to include your existing fence as part of your layout and
keep your pet from jumping out or digging under your existing fence. It reduces
the amount of wire which will need to be buried. Run the wire from the Fence
Transmitter to A, Ato B, Bto C, Cto D, Dto E, Eto F, make a U-turn and
follow your path all the way back to A, keeping the wire separated three to five
feet.Twist the wire from Aback to the Fence Transmitter. See the “Install the
Boundary Wire” section for more information on attaching the wire to a fence.
3-5'
E
F
B
A
D
C
__________________________________________________
Position the Boundary Wire
Lay out the Boundary Wire using your proposed boundary and test the system BEFORE burying the wire or
attaching it to an existing fence.This will make any layout changes easier.
Running the Boundary Wire parallel to and within five feet of electrical wires, neighboring containment systems,
telephone wires, television or antenna cables, or satellite dishes will cause an inconsistent signal. If you must cross
any of these, do so at 90-degree angles (perpendicularly).
If separating your Boundary Wire by at least five feet from a neighboring containment system’s wire does not reduce
the inconsistent signal, contact the Customer Care Center at 1-800-732-2677.
To Twist the Boundary Wire (3A)
Twisting the Boundary Wire cancels the signal and allows your pet to cross over that area safely. Plastic or metal
piping will not cancel the signal. Twist the Boundary Wire 8 to 10 times per foot to cancel the signal.
To Splice or Repair the Boundary Wire (3B)
If you need additional Boundary Wire to expand your wire loop, you will need to splice the wires together. Note the
locations of all splices for future reference. Most Boundary Wire breaks occur at splices.
Strip approximately one-half inch of insulation off the ends of the Boundary Wires to be spliced. Make sure the
copper Boundary Wire is not corroded. If the Boundary Wire is corroded, cut it back to expose clean copper wire.
Insert the stripped ends into the wire nut and twist the wire nut around the wires. Pull on the wires to make sure
you have a strong splice connection. Apply waterproofing compound (e.g. silicone caulk) in and around the wire nut
or wrap the wires and the wire nuts with electrical tape to prevent moisture from corroding the copper.
If your splice pulls loose, the entire system will fail. Make sure your splice is secure.
10 Twists/ft.
1
1/2" 1/2"
2
Step
3

8 1-800-732-2677
Additional Boundary Wire
We recommend the use of 20 gauge insulated multi-strand copper
wire for direct burial. Extra Boundary Wire can be purchased in 500
foot spools at the store where you purchased the kit or through the
Customer Care Center at 1-800-732-2677.
Note:When adding BoundaryWire, it must act as a continuous loop.
The table at right indicates the approximate length of Boundary Wire
needed for a rectangular, Single Loop layout. Length will vary due to
the amount of twisted wire and layout used.
Acres Feet of Wire Needed
1/4 415
1/3 480
1/2 590
1 835
2 1180
5 1870
25 4000
__________________________________________________
Connect the Wires to the Fence Transmitter
Boundary Wire (4A)
1. Run the Boundary Wire to the Fence Transmitter through a window, under
a door, through a crawl space vent, or any other appropriate available access.
You can also drill a hole through your wall.
2. Strip the ends of the Boundary Wire approximately one-half inch.
3. Insert the Boundary Wires into the Boundary Wire Terminals on the Fence
Transmitter.
4. Turn the Boundary Width Control knob to 10. This will set the Warning Zone
at the maximum width.
5. Plug the Power Adapter into the Power Jack and a 120-volt outlet.
6. The Power Light and Loop Indicator Lights should come on. If this does not
happen, see the “Troubleshooting” section.
}
Boundary Width
Control
Power Light
Loop Indicator
Light
Boundary Wire
Terminals
Ground
Terminal
Power
Jack
4A
Ground Wire (4B)
Proper grounding, although not necessary for the system to work, will
help reduce the chance of electrical surges causing damage to your Fence
Transmitter and/or Power Adapter. To ground your unit, you will need a solid
(not stranded) Ground Wire (14 to 18 gauge insulated copper wire) and a
ground rod with clamp, which may be obtained at most electrical supply stores.
Connect one end of the Ground Wire to the Ground Terminal located on the
Fence Transmitter and the other end of the Ground Wire to the ground rod.
The ground rod must be buried at least three feet into the ground and located
as close as possible to the Fence Transmitter.
Ground
Wire
4B
Fuse Protection (4C)
The Fence Transmitter is also equipped with a 250 volt, ½ amp fuse to protect the
unit’s electronic circuitry from electrical power surges. To locate the fuse, slide off
the lid on the back of the Fence Transmitter. A spare fuse is also provided.
Lightning Protection
You may purchase a Lightning Protection Kit through the Customer Care Center
at 1-800-732-2677. The Lightning Protection Kit protects the system against
surges that travel through the power source and/or the Boundary Wire. If you use
a Lightning Protection Kit, the Ground Wire must be removed from the Fence
Transmitter. The Lightning Protection Kit utilizes a ground connection separate
from the Fence Transmitter.
Spare Fuse
Fuse
4C
Step
4

www.petsafe.net 9
Prepare the Receiver Collar
Your Receiver Collar comes with short Contact Points installed. Use the long Contact Points for pets with long
or thick hair. Tighten the Contact Points with pliers one-half turn beyond finger tight (5A). Check the tightness
weekly.
To Insert and Remove the Battery
Note: Do not install the battery while the Receiver Collar is on your pet.
This Receiver Collar utilizes a replaceable PetSafe®battery (RFA-67). This unique battery is designed to make battery
replacement easier and increase water protection.
To insert the battery, align the symbols on the battery (arrow) and Receiver Collar (triangle) (5B). Use a large coin
to turn the battery clockwise until the arrow lines up with the lock symbol on the housing (5C) .
To remove the battery, turn the battery counter-clockwise using a large coin (5D, 5E). DO NOT attempt to cut
into or pry open the battery. Be sure to discard the used battery properly.
A replacement PetSafe®battery (RFA-67) can be found at many retailers. Contact the Customer Care Center at
1-800-732-2677 or visit our web site at www.petsafe.net to locate a retailer near you.
W
WW
PA
TIEN
3
3
2
A-67
4
1
2
5
To Set the Static Correction Level
Read all steps before attempting to set the
Static Correction Level.
1. Remove the clear plastic cover with a coin
to expose the Correction Level Button (5F).
2. With the battery installed, press the
Correction Level Button and release when
the Receiver LED Indicator Light lights up
(5G).
3. The Receiver LED Indicator Light will
emit a series of flashes representing the
Static Correction Level.
4. Increase the Static Correction Level by
pressing and releasing the Correction Level
Button within 5 seconds of the previous
series of flashes.
5. After setting the Static Correction Level,
5F 5G
replace the cover to protect the Correction Level Button.
The Static Correction levels increase in strength from 1 to 5. Pushing the Correction Level Button while the
Receiver Collar is on level 5 will cause the Receiver Collar to revert to level 1. Refer to the Function and Response
Table to choose the Static Correction level that best fits your pet.
The Receiver Collar is equipped to automatically increase the level of Static Correction the longer your pet remains
in the Static Correction Zone if the collar is set at level 2 or above.
The Receiver LED Indicator Light acts as a low battery indicator, flashing every 4 to 5 seconds when replacement
is required.
Step
5

10 1-800-732-2677
Function and Response Table
Indicator Light
Response
Static
Correction Level
Receiver Collar Function Temperament of Pet
1 Flash 1 No Static Correction, Beep Only
2 Flashes 2 Low Static Correction Timid
3 Flashes 3 Medium Static Correction Timid or Average
4 Flashes 4 Medium High Static Correction Average or High Energy
5 Flashes 5 High Static Correction High Energy
Flashes once every
4 to 5 seconds
Low Battery
Note: Begin training with Static Correction Level 2 and only increase if your pet does not respond to the Static Correction.
__________________________________________________
Set the Boundary Width
and Test the Receiver Collar
The Boundary Control Switch on the side of the
Fence Transmitter has three settings (6A). Setting
Bis used for most properties.The following table
will indicate the setting you should use.
Amount of Wire Setting
Up to 1300 feet B
1300-2400 C
Greater than 2400 feet A
Use the Boundary Width Control knob to set the
width of the Warning Zone and Static Correction
Zone (6B). Set the Boundary Width as wide as
possible to give your pet the widest Warning and
Static Correction Zones without reducing the Pet
Area too much.
6A
5
28
4
10
3
9
1
7
0
6
5
28
4
10
3
9
1
7
0
6
6B
Note:The BoundaryWidth Control knob does not change the Static Correction Level.
To identify the Warning and Static Correction
Zones, make sure the Receiver Collar battery is
properly installed, the Static Correction Level is
set at 2 or above, and the Test Light is attached
to the Contact Points (6C, 6D). Walk toward
the Boundary Wire with Contact Points pointing
up and holding the Receiver Collar at your pet’s
neck level (6E) until the Receiver Collar beeps
(6F).
Note:The Receiver Collar is waterproof, which can
make the beep hard to hear.
6C 6D
Step
6