Petsafe Pawz Away ZND-1200 Setup guide

PetSafe®Pawz Away®
Indoor Pet Barrier
Operating andTraining Guide
Please read this entire guide before beginning.
®
www.petsafe.net
Model
Number
ZND-1200

2 Customer Care Center 1-800-732-2677
Important Safety Information
Explanation of Attention Words and Symbols used in this guide
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
CAUTION, used without the safety alert symbol, indicates a hazardous
situation which, if not avoided, could result in harm to your pet.
NOTICE
NOTICE is used to address safe use practices not related to
personal injury.
WARNING
Not for use with aggressive dogs. Do not use this product if your dog is prone to
aggressive behavior. Aggressive dogs can cause severe injury or death to their
owners and others. If you are not sure that this product is right for your dog,
please talk to your veterinarian or a certified trainer.
CAUTION
This System is NOT a solid barrier. The system is designed to act as a
deterrent, using Static Correction to condition pets to remain outside of the
established barrier area. It is important that you reinforce training with your pet
on a regular basis. Since the tolerance level to Static Correction varies from
pet to pet, Radio Systems®Corporation CANNOT guarantee that the system
will in all cases keep a pet outside of the established barrier area. Not all pets
can be trained to avoid entering the barrier area. Therefore, if you have reason
to believe that your pet may harm himself or pose a danger to others if he is
not kept from entering the barrier area, you should NOT rely solely upon this
system to restrict your pet. Radio Systems®Corporation shall NOT be liable for
any personal injuries, property damage, injury to or death of your pet, economic
loss or any consequential damages sustained as a result of any animal
entering the barrier area.

www.petsafe.net 3
CAUTION
Proper fit of the collar is important. A collar worn for too long or made too
tight on the pet’s neck may cause skin damage. Ranging from redness to
pressure ulcers; this condition is commonly known as bed sores.
- Avoid leaving the collar on the dog for more than 12 hours per day.
- When possible reposition the collar on the pet’s neck every
1 to 2 hours.
- Check the fit to prevent excessive pressure; follow the instructions
in this manual.
- Never connect a lead to the electronic collar; it will cause
excessive pressure on the contacts.
- When using a separate collar for a lead, don’t put pressure on the
electronic collar.
- Wash the dog’s neck area and the contacts of the collar weekly
with a damp cloth.
- Examine the contact area daily for signs of a rash or a sore.
- If a rash or sore is found, discontinue use of the collar until the skin
has healed.
- If the condition persists beyond 48 hours, see your veterinarian.
- For additional information on bed sores and pressure necrosis,
please visit our website.
These steps will help keep your pet safe and comfortable. Millions of pets
are comfortable while they wear stainless steel contacts. Some pets are
sensitive to contact pressure. You may find after some time that your pet is
very tolerant of the collar. If so, you may relax some of these precautions.
It is important to continue daily checks of the contact area. If redness or
sores are found, discontinue use until the skin has fully healed.
You may need to trim the hair in the area of the Contact Points. Never
shave the dog’s neck; this may lead to a rash or infection.
To prevent an unintended correction, do not perform set up procedures while•
the Receiver Collar is on your pet.
If you are using a collar and leash for training, be sure the extra collar does not•
put pressure on the Contact Points of the Receiver Collar.
NOTICE
To avoid damage to the transmitter do not use on wet surfaces, in damp or
wet locations or around swimming pools. This product is designed for indoor
use only. Do not expose to rain or snow.

4 Customer Care Center 1-800-732-2677
Thank you for choosing PetSafe®brand.You and your pet deserve a
companionship that includes memorable moments and a shared understanding
together.Our products and training tools promote a lifestyle of protection,
teaching, and love — essentials that influence memories for a lifetime. If you have
any questions about our products or training your pet, please visit our website at
www.petsafe.net or contact our Customer Care Center at 1-800-732-2677.
To get the most protection out of your warranty, please register your product
within 30 days at www.petsafe.net. By registering and keeping your receipt,
you will enjoy the product’s full warranty and should you ever need to call the
Customer Care Center, we will be able to help you faster. Most importantly,
PetSafe®will never give or sell your valuable information to anyone. Complete
warranty information is available online at www.petsafe.net.
Table of Contents
Components.............................................................................................. 5
Other ItemsYou May Need......................................................................... 5
How the SystemWorks............................................................................... 6
Key Definitions.......................................................................................... 6
Operating Guide...................................................................................... 7
Install the BarrierTransmitter.................................................................. 7
Set Up the BarrierTransmitter................................................................. 7
Test the Barrier Area ............................................................................... 8
Fit the Receiver Collar onYour Pet........................................................... 9
To Re-Thread the Collar ........................................................................10
Receiver Collar Batteries ........................................................................11
Additional Features................................................................................11
Time Out Feature..................................................................................11
Mode A, B, and AB Feature....................................................................11
Programming the Mode Settings.............................................................13
Training Guide .......................................................................................14
BeginYour Pet’s First Session .................................................................14
FurtherTraining.....................................................................................14
Additional Information..............................................................................14
Accessories ...............................................................................................15
Troubleshooting......................................................................................15
Terms of Use and Limitation of Liability....................................................16
Compliance ..............................................................................................17
Customer Care International.....................................................................17
Perchlorate Battery....................................................................................17

www.petsafe.net 5
Components
Barrier Transmitter
(3 AA Batteries not included)
Operating and
Training Guide
(4) Barrier Transmitter
Grip Pads
Test Light Tool
Receiver Collar
(2) 3-V Lithium
Batteries for
Receiver Collar
®
www.petsafe.net
PetSafe
®
Pawz Away
®
Indoor Pet Barrier
Operating and Training Guide
Pleaseread thisentireguide beforebeginning.
®
www.petsafe.net
Model
Number
ZND-1200
Other ItemsYou May Need
Drill and mounting hardware• Non-metallic collar and leash• Scissors• Lighter•

6 Customer Care Center 1-800-732-2677
How the SystemWorks
The PetSafe®Pawz Away®Indoor Pet Barrier keeps your pet away from a certain room, away from
trash, off of furniture, etc. Just place the BarrierTransmitter near the area your pet should avoid.
The BarrierTransmitter sends a spherical radio signal, reaching up to 12 feet in diameter or a 6
foot radius.Your pet wears a Receiver Collar with Contact Points that touch his neck.When your
pet enters the Barrier Area,he’ll hear a series of audible tones from the Receiver Collar and he
will feel a safe Progressive Static Correction, delivered through the Contact Points on his neck.
The Progressive Static Correction will get his attention, but will not cause harm.The correction
continues until your pet leaves the Barrier Area.The PetSafe®Pawz Away®Indoor Pet Barrier has
been proven safe, comfortable, and effective for pets at least 6 months old and 5 pounds or more.
Key Definitions
BarrierTransmitter:Transmits the wireless radio signal.
Barrier Area: Area that you want to prevent your pet from gaining access to.
Receiver Collar: Receives the radio signal from the BarrierTransmitter.
Contact Points: Deliver the safe Progressive Static Correction when your pet enters the Barrier Area.
Progressive Static Correction: Static correction begins at the lowest level and automatically
increases to maximum within 3 seconds of first detection in the Barrier Area.
Barrier
Transmitter
Barrier
Area
Receiver
Collar
LCD
Display
Window Up Button
Down Button
®
www.petsafe.net
ON
OFF
OPEN
Contact Points
On/Off Dial
Open Battery

www.petsafe.net 7
Operating Guide
Install the BarrierTransmitter
The BarrierTransmitter emits a radio signal from all sides in a spherical pattern.The
signal may transmit through a wall or the ceiling/floor.The BarrierTransmitter can
be placed laying flat on a surface or hung on a wall. If you choose to hang the Barrier
Transmitter, note that the signal becomes very directional—the signal will be strongest
directly in front of and behind the unit.The signal is weakest to the side of the unit.
Do not:
Hang unit on a metal wall• Place BarrierTransmitter on metal surfaces• Place BarrierTransmitter near large metal objects such as refrigerators, washers, etc.• Place BarrierTransmitter near audio speakers•
To keep the BarrierTransmitter in place on smooth surfaces, place the four grip pads to
the bottom of the unit.
NOTICE
To avoid damage to the transmitter do not use on wet surfaces, in damp or
wet locations or around swimming pools. This product is designed for indoor use only.
Do not expose to rain or snow.
Set Up the BarrierTransmitter
CAUTION
To prevent an unintended correction, never perform set-up procedures while
your pet is wearing the Receiver Collar.
Turn over the BarrierTransmitter and slide open the1. battery door. Install three AA alkaline batteries and
replace the battery door.
Turn the BarrierTransmitter right side up and press2. the UP (+) arrow button once to turn ON the Barrier
Transmitter.A black bar in the upper right hand corner
of the LCD display window indicates that the Barrier
Transmitter is set to mode A* (2A).A second black bar
in the bottom of the LCD display indicates the range is
set to one segment.
Each segment represents approximately two feet of3. diameter.You can create a Barrier Area of 2 feet in
diameter up to 12 feet in diameter. Using the UP (+)
and DOWN (-) arrow buttons,adjust the range to fit
the desired pet Barrier Area.
2A
*All Indoor Barriers and Receiver Collars are preset to mode A.The A and B mode
feature is designed to be used in multiple pet households where you may want one
pet to be able to access an area while preventing access by another pet. For single pet
households, you will not need to operate the BarrierTransmitter in any mode other
than A. Please see theAdditional Features section of this operating and training guide
(beginning on page 11) for instructions on how to utilize mode A and B.
Step
1
Step
2

8 Customer Care Center 1-800-732-2677
Test the Barrier Area
Keeping your hands away from the Contact Points, use1. the edge of theTest LightTool to turn the receiver battery
door to the ON position.
Hold the Receiver Collar with the Contact Points facing2. up. Place theTest LightTool on the Contact Points so that
the wire in theTest LightTool touches the Contact Points
(3A).The PetSafe®logo on the Receiver Collar should
face theTransmitter.
Hold the Receiver Collar at the approximate height of3. your dog’s neck (3B). Start outside of the range and walk
slowly toward the BarrierTransmitter.As you reach the
Barrier Area, the Receiver Collar emits a series of high-
pitched tones.For each tone you hear, you should notice
theTest Light flashing which indicates that a Progressive
Static Correction is being delivered.The Receiver Collar’s
tone is easily heard by dogs but may be at a volume level
difficult for some humans to hear.
Check the range of the Barrier Area from multiple angles4. to ensure you are getting the desired coverage.
Note:Should you find that you are not getting the desired range
at the maximum setting,move the BarrierTransmitter a few feet,
or change from its standing-on-end position to laying flat.Metal
objects can alter the magnetic field and change the transmitting
signal range.The effect on the range depends on the size and
shape of the objects.Signal range can be reduced if the Barrier
Transmitter is placed on a concrete floor,due to steel reinforcement
in the concrete.For best range results,place the BarrierTransmitter
on a nonconductive surface,i.e.,wood floor or table.Placing the
3A
3B
BarrierTransmitter beneath sofas and beds can reduce the range due to the metal springs altering the
magnetic field.
Step
3

www.petsafe.net 9
Fit the Receiver Collar onYour Pet
Important: Proper fit and placement of your Receiver Collar is necessary for
effective operation.The Contact Points must have direct contact with your pet’s
skin on the underside of his neck.
CAUTION
Proper fit of the collar is important. A collar worn for too long or made too tight on
the pet’s neck may cause skin damage. Ranging from redness to pressure ulcers; this
condition is commonly known as bed sores.
Avoid leaving the collar on the dog for more than 12 hours per day.•
When possible reposition the collar on the pet’s neck every 1 to 2 hours.•
Check the fit to prevent excessive pressure; follow the instructions in this manual.•
Never connect a lead to the electronic collar; it will cause excessive pressure on the•
contacts.
When using a separate collar for a lead, don’t put pressure on the electronic collar.•
Wash the dog’s neck area and the contacts of the collar weekly with a damp cloth.•
Examine the contact area daily for signs of a rash or a sore.•
If a rash or sore is found, discontinue use of the collar until the skin has healed.•
If the condition persists beyond 48 hours, see your veterinarian.•
For additional information on bed sores and pressure necrosis, please visit our website.•
These steps will help keep your pet safe and comfortable. Millions of pets are comfortable
while they wear stainless steel contacts. Some pets are sensitive to contact pressure. You
may find after some time that your pet is very tolerant of the collar. If so, you may relax
some of these precautions. It is important to continue daily checks of the contact area. If
redness or sores are found, discontinue use until the skin has fully healed.
You may need to trim the hair in the area of the Contact Points. Never shave the dog’s
neck; this may lead to a rash or infection.
To assure a proper fit, please follow these steps:
Using the edge of theTest LightTool, turn the battery door to the1. OFF position.
Start with your pet standing comfortably (2. 4A).
Place the Receiver collar on your pet so that the PetSafe3. ®logo is facing
your pet’s chin. Center the Contact Points underneath your pet’s
neck, touching the skin. If your pet has a long or thick coat then it may
be necessary to trim the hair around the Contact Points to make sure
that contact is consistent.
4A
Note:The Receiver Collar comes with Short Contact Points.Long Contact Points are available
and can be purchased through the Customer Care Center.Please see the Accessories section of
this Operating andTraining Guide for more information.
Step
4

10 Customer Care Center 1-800-732-2677
Adjust the tightness of the Receiver Collar to4. fit your pet’s neck. Check the tightness of the
Receiver Collar by inserting one finger between
the end of a Contact Point and your pet’s neck.
The fit should be snug but not constricting (4B).
Allow your pet to wear the Receiver Collar for5. several minutes then recheck the fit. Check the
fit again as your pet becomes more comfortable
with the Receiver Collar.
Once you are satisfied with the fit of the6. Receiver Collar then you may trim any excess
collar strap as follows (4C):
Mark the desired length of the Receivera. Collar with a pen. Allow for growth if your
pet is young or grows a thick winter coat.
Remove the Receiver Collar from your petb. and cut off the excess.
Before placing the Receiver Collar back ontoc. your pet, seal the edge of the cut collar by
applying a flame along the frayed edge.
4B
4C
To Re-Thread the Collar
Slide Buckle
Ridges
The slide buckle prevents the collar from
becoming loose around your pet’s neck.
The ridges must be facing up; the collar will slip if
it is not properly threaded.

www.petsafe.net 11
Receiver Collar Batteries
The PetSafe®Pawz Away®Receiver Collar uses two 3-volt Lithium
coin cell batteries, size CR2032.Replacement batteries can be
found at many retailers or through the Customer Care Center.
Contact the Customer Care Center at 1-800-732-2677 or visit
our website at www.petsafe.net to locate a retailer near you.
To replace the batteries:
Using the edge of theTest LightTool, turn the battery door to1. the OPEN position.
Lift the battery door out and turn the door over.The two 3-volt2. Lithium coin cell batteries are stored inside the door.
Remove the old batteries and insert new batteries with the3. positive (+) side facing the battery door lid.
Insert battery door back into the Receiver Collar and turn to4. either the OFF or ON position to lock the door in place.
Battery life will vary depending on how often your pet tests the
system and receives a Static Correction. Check the Receiver
Collar and BarrierTransmitter every month to ensure the system
is working properly.To prolong battery life, it is recommended
that you turn the Receiver Collar and BarrierTransmitter OFF
when not in use.
ON
OFF
OPEN
ON
OFF
OPEN
Open
Battery
Additional Features
Time Out Feature
For your pet’s safety, the Receiver Collar has a built inTime Out feature. If your pet stays in the
Barrier Area for longer than 15 seconds the Receiver Collar will stop delivering the Progressive
Static Correction.The Receiver Collar will then administer a random single Static Correction
every 5 to 10 seconds at the maximum level until the pet leaves the Barrier Area.Once your
pet leaves the Barrier Area, the Receiver Collar resets itself and will deliver a Progressive Static
Correction the next time your pet enters the Barrier Area.
Mode A, B, and AB Feature
For multiple pet households,additional PetSafe®Pawz Away®Receiver Collars can be purchased
to work with one or more PetSafe®Pawz Away®Indoor BarrierTransmitters.You can set up an
unlimited number of BarrierTransmitters in your home and an unlimited number of Receiver
Collars can be used with one or more BarrierTransmitters. If you have multiple pets, you may
want to allow one pet access to an area while denying access to another pet.With the purchase of
additional Receiver Collars and BarrierTransmitters, you can accomplish this by using the Mode
A and Mode B functions.
All PetSafe®Pawz Away®Indoor BarrierTransmitters and Receiver Collars come preset to
mode A. Each Receiver Collar can operate in one of two different modes—A or B. Each Barrier
Transmitter may be set to either A, B or AB mode to allow for multiple configurations.

12 Customer Care Center 1-800-732-2677
Barrier
Transmitter
Barrier
Transmitter
Barrier
Transmitter
When the BarrierTransmitter and Receiver Collar are
set to mode A, the BarrierTransmitter denies access to
pets wearing a Receiver Collar programmed to mode A.
Receiver Collars set to mode B will not pick up the signal
from a BarrierTransmitter set to mode A.
When the BarrierTransmitter and Receiver Collar are
set to mode B, the BarrierTransmitter denies access to
pets wearing a Receiver Collar programmed to mode B.
Receiver Collars set to mode A will not pick up the signal
from a BarrierTransmitter set to mode B.
When the BarrierTransmitter is set to mode AB,the
BarrierTransmitter denies access to all pets wearing the
Receiver Collar, no matter which mode the receiver is
programmed to.

www.petsafe.net 13
Programming the Mode Settings
All programming is done through the BarrierTransmitter and the programming is synchronized
with the Receiver Collar.The Receiver Collar cannot be programmed separately from the
BarrierTransmitter.
You may synchronize multiple Receiver Collars to a single BarrierTransmitter at one time.
However, make sure any Receiver Collar you do not wish to synchronize is turned OFF during the
programming procedure. Any collar that is within 5 feet of the BarrierTransmitter and turned ON
may be reprogrammed. Familiarize yourself with the steps outlined below before attempting to
program the BarrierTransmitter and Receiver Collar.
CAUTION
To prevent an unintended correction, do not perform set up procedures while the
Receiver Collar is on your pet.
Gather the Receiver Collar(s) you wish to synchronize with the BarrierTransmitter.Turn the1. Receiver Collar(s) ON and place less than one foot from the BarrierTransmitter.
Turn the BarrierTransmitter OFF by pressing the DOWN (-) arrow button until there are no2. bars displayed in the LCD window. Remove the battery door.
The mode switch is located inside the3. transmitter and is preset to mode A.
Move the switch to the center position for
mode B or to the right position for mode
AB (5A). Once you have selected the
desired mode, replace the battery door.
Note:If you have selected mode AB you do
not need to proceed with programming the
receiver in the next steps.Receiver Collars
set to mode A or mode B will each receive
the radio signal from a BarrierTransmitter
set to mode AB.
Inside
Battery
Door
Transmitter
Inside View
5A
To program the Receiver Collar to either mode A or mode B, press and hold the DOWN4. (-) arrow button and then press the UP (+) arrow button for approximately 5 seconds.
Programming is complete when you hear a series of three beeps from the Receiver Collar.
Once the Receiver Collar has been programmed, press the UP (+) arrow button to turn the5. BarrierTransmitter ON.Check to make sure the black bar(s) appear on the LCD screen
indicating the mode you have selected (5B) and reset the BarrierTransmitter to the desired range.
Mode A Mode B Mode AB
5B

14 Customer Care Center 1-800-732-2677
Training Guide
The PetSafe®Pawz Away®Indoor Pet Barrier operates on the principle of positive and negative
reinforcement.Your pet will learn to avoid the Barrier Areas you have set after receiving a
Progressive Static Correction (negative reinforcement) and your pet will learn that he is more
comfortable when he avoids the Barrier Areas (positive reinforcement).
In some cases, it may not be necessary to train your pet.You can let your pet wander freely
to determine the new boundaries. Monitor your pet during his first session. Pets learn at
different rates and it may take several times for your pet to successfully understand and honor the
Barrier Areas.
BeginYour Pet’s First Session
Move your pet away from the Barrier Area.1. Activate the Receiver Collar by turning the battery door to the ON position. Place the Receiver2. Collar around your pet’s neck. Be sure that the Receiver is directly under your pet’s neck.
Allow your pet to wander freely to learn the new boundaries.3.
FurtherTraining
If your pet is confused or unsure how to avoid the Barrier Areas then you may need to teach your
pet how to do so by following these easy training steps:
Place a second non metallic collar on your pet ABOVE the Receiver Collar and attach a1. long leash.
CAUTION
Be sure the extra collar does not put pressure on the Contact Points of the
Receiver Collar.
Walk your pet toward the Barrier Area.As soon as you hear the tone or you see that your pet is2. receiving a Static Correction, gently pull him away from the Barrier Area and back into the safe zone.
Reward your pet with praise each time he leaves the Barrier Area.3. Practice this technique a few times until you feel that your pet is mastering avoidance of the4. Barrier Areas.
Be sure to never force or entice your pet to enter the Barrier Areas.
Additional Information
The system should only be used with healthy pets. Contact your veterinarian if you have• concerns about the medical condition of your pet (medication, pregnant, heart conditions, etc).
This system is not for vicious or aggressive pets. If your pet may pose a threat to others,• DO
NOT USETHIS SYSTEM. If you are unsure if your dog is aggressive, please consult your
veterinarian or a certified trainer.

www.petsafe.net 15
Accessories
To purchase additional accessories for your PetSafe®Pawz Away®Indoor Pet Barrier, contact the
Customer Care Center at 1-800-732-2677 or visit our website at www.petsafe.net to locate a
retailer near you.
Component Part Number
Battery – 3Volt Lithium (two pack - size CR2032) RFA-35-11
Replacement Strap RFA-308
Extra Receiver Collar RFA-377
Extra BarrierTransmitter ZND-1000
Replacement Short and Long Contact Points RK-17
Receiver Collar Battery Door RFA-394
Troubleshooting
BarrierTransmitter does not
appear to work. Check segment indicator on BarrierTransmitter.• Check/replace batteries in BarrierTransmitter.• Increase the Barrier Area range on the Barrier• Transmitter.
Check that the BarrierTransmitter setting corresponds• to the Receiver Collar setting. (i.e. BarrierTransmitter
is set to mode A and Receiver Collar is synchronized to
pick up mode A)—refer to Additional Features section
beginning on page 11 for instructions.
Barrier Area range is too low. Check/replace batteries in Receiver Collar.• Adjust BarrierTransmitter range to increase Barrier• Area size.
Barrier Area range is too high. Adjust BarrierTransmitter range to decrease Barrier• Area size.
Pet seems to receive no
stimulation. Check/replace batteries in Receiver Collar.• UseTest LightTool to check for static correction.• Check Receiver Collar fit to ensure Contact Points have• direct skin contact.
Check the setting on the BarrierTransmitter.•
Unable to hear Receiver Collar
tone. Check/Replace batteries in Receiver Collar.• Pets easily hear tone but it may be a volume level that is• difficult for you to hear.
Use theTest LightTool to check Receiver Collar for• static correction.
No segments on Barrier
Transmitter. Press the UP (+) arrow button.• Check/replace batteries in BarrierTransmitter.•

16 Customer Care Center 1-800-732-2677
Terms of Use and Limitation of Liability
Terms of Use1.
This Product is offered to you conditioned upon your acceptance without modification of the terms,
conditions and notices contained herein. Usage of this Product implies acceptance of all such terms,
conditions, and notices.
Proper Use2.
This Product is designed for use with pets where training is desired.The specific temperament of your
pet may not work with this Product.We recommend that you not use this Product if your pet is less
than 5 pounds or if your pet is aggressive. If you are unsure whether this is appropriate for your pet,
please consult your veterinarian or certified trainer.
Proper use includes reviewing the entire Guide provided with your Product and any specific
Caution statements.
No Unlawful or Prohibited Use3.
This Product is designed for use with pets only.This pet training device is not intended to harm, injure
or provoke. Using this Product in a way that is not intended could result in violation of Federal,State
or local laws.
Limitation of Liability4.
In no event shall Radio Systems®Corporation be liable for any direct,indirect, punitive, incidental,
special or consequential damages, or any damages whatsoever arising out of or connected with the use
or misuse of this Product. Buyer assumes all risks and liability from the use of this Product.
Modification of5. Terms and Conditions
Radio Systems®Corporation reserves the right to change the terms, conditions and notices under
which this Product is offered.

www.petsafe.net 17
Compliance
FCC/Canada
This Class B digital apparatus complies with Canadian ICES-003.This equipment has been tested
and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules.These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a residential environment.This equipment generates, uses,and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction
guide, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a practical installation. If this equipment causes harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
Relocate the interfered receiving antenna.• Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different to that to which the receiver is connected.•
Contact the Customer Care Center at 1-800-732-2677.•
This device complies with Industry Canada Rules.This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful
interference, and (2) this device must accept any interference received,including interference that
may cause undesired operation.
Unauthorized changes or modifications to the equipment, not approved by Radio Systems®
Corporation, could result in not meeting compliance with FCC regulations and could void the
user’s authority to operate the equipment.
Australia
This device complies with the applicable EMC requirements specified by the ACMA (Australian
Communications and Media Authority).
Customer Care International
USA & Canada -Tel: [phone]
Monday - Friday 8 AM - 8 PM / Saturday 9 AM – 5 PM
Australia -Tel: [phone]
Monday - Friday 9 AM - 5 PM
New Zealand -Tel: [phone]
Monday - Friday 12 PM - 7 PM
This product has the benefit of a limited manufacturer’s warranty. Details of the warranty
applicable to this product and its terms can be found at www.petsafe.net and/or are available by
sending a stamped addressed envelope to PetSafe®Ltd. Redthorn House, Unit 9, ChorleyWest
Business Park,Ackhurst Road, Chorley, Lancashire PR7 1NL, United Kingdom.
Perchlorate Battery
Perchlorate Material – special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.

18 Customer Care Center 1-800-732-2677

www.petsafe.net 19

Radio Systems®Corporation
10427 Electric Avenue
Knoxville,TN 37932
1-800-732-2677
www.petsafe.net
Protected by US Patents 7,046,152; 7,068,174;
7,117,822; 7,204,204; 7,278,376; 7,495,570.
Other patents pending.
400-1062/3
©2008 Radio Systems Corporation