PG BISON BLUM FLATPAX Series User manual

GSPublisherVersion 183.1.8.100
BLUM FLATPAX KITCHEN RANGEASSEMBLY GUIDEWALL CABINET CORNER - LEFT 850mmSys5 Quickfit TL2 Dowel 8 x 34Sys5 Cam 3000 15 x 14 mmScrew 4.0 x 30mmA - Left SideC - Wall BottomG - BackI - Adjustable ShelfB - Right SideD - TopH - BackF - SpacerE - Panel DummyTOTAL NUMBER OF PANELS: 9HARDWAREPRODUCTQTYScrew 3.5 x 16mm141Wooden Dowel Titus 8 x 30 mm28Screw Nail in Anchor 8 x 80mm Yellow1214142APC 1 Wall Cabinet Hanger KitCabinet Connecting Screw Kit4H Profile Backer Connector1Shelf Support Flipper 14mm Kit4IMAGE

GSPublisherVersion 183.1.8.100
22TOOLS REQUIREDScrew Driver(Pozidriv Head)Cordless DrillPozi Bit (PZ2) 1. Confirm that all panels (6) are in the package before assembling. 2. Check the white sticker on each panel for the labelling (A, B, C, D, E, F, G, H & I). 3. Ensure that the panels are laid on a non-abrasive surface when assembling. 4. Note that all panel connections are done using the system described below.Rubber Mallet8mm Drill Bit2 O'ClockPosition230°PANEL CONNECTION AND FASTENINGGENERAL INSTRUCTIONSDet. 1Det. 2Det. 3IIIIIIIVI - Insert the Minifix (1), Dufix (1) and wooden dowels (2) in the shown positions.Gently knock in the wooden dowels using a rubber mallet where necessary.II - Confirm that the Minifix orientation is as shown in Det. 1 then connect thepanels.III - Using a screw driver, turn the Minifix 230° clockwise to fasten the panelstogether. Refer to Det. 2.IV - See Det. 3 for Minifix orientation when fastened. Reset the Minifixorientation to that shown in Det.1 to disconnect the panels.

GSPublisherVersion 183.1.8.100
3Dowel-Dufix-Dowel holes forpanel connectionDowel-Dufix-Dowel holes forpanel connectionCabinet connectionholes for CabinetConnecting Screws.Shelf stud holes forflipper euro dowels.Cabinet connectionholes for CabinetConnecting Screws.PILOT HOLES KEY FOR SIDE PANELS

GSPublisherVersion 183.1.8.100
STEP 1STEP 2Connect panel E to panel D as shown. Refer to the holes and/or grooves on the diagram todetermine the panel orientation.Connect panel E to panel C as shown. Refer to the holes and/or grooves on the diagram todetermine the panel orientation.4DECDEHinge Plate HolesHinge Plate Holes

GSPublisherVersion 183.1.8.100
STEP 3STEP 4Connect panels C & D to panel A as shown. Refer to the holes and/or grooves on the diagram todetermine the panel orientation.Connect panel B to panels C & D as shown. Refer to the holes and/or grooves on the diagram todetermine the panel orientation.5DCCDEBAA

GSPublisherVersion 183.1.8.100
STEP 5STEP 6First, check the diagonal of the cabinet by measuring the two distances indicated by the red,broken lines. They should be equal. If not, twist the cabinet accordingly in the diagonal corners asshown until an equal value is achieved. After, place the APC 1 hangers in the shown positionsensuring that the shaded areas are flush with each other. Then, secure panel H to panel C usingScrew 3.5 X 16mm (5) and panel G to panel D, through the APC 1 hangers, using Screw 4 X 30mm(2). Reinforce the APC 1 hangers and panel G in the shown positions using Screw 3.5 X 16mm.6Screw 3.5 x16mmX 5GSlide 3mm panel H into the groove on panels A & B with the finished side facing inside the cabinet.After, insert the H Profile Backer Connector into panel H as shown (See Det. 4). To finish this step,slide 3mm panel G through the groove on panels A & B and into the H Profile Backer Connector asshown in Det. 4.HDet. 4IIIIIIGScrew 4 x30mmX 2Screw 3.5 x16mmX 3Screw 3.5 x16mmX 4APC 1HDBCAGHDA

GSPublisherVersion 183.1.8.100
STEP 7STEP 8I) Separate the yellow plug from the nail in anchor and, using a rubber mallet, gently knock in theplug into the holes drilled in Step 5.II) Place the APC 1 wall plates on the wall. Align the oval holes on the wall plate with the plugs.III) Screw the nail in anchor into the yellow plug.7The broken lines indicate the outer boundaries of the wall cabinet. Mark the drill points on the wallwith respect to the hanging position of the wall cabinet. Refer to Det. 5 for dimensions. Then, usingan 8mm Drill Bit, drill 80mm deep holes through the marked positions on the wall ensuring that thedrill bit is perpendicular to the wall surface.
32mm
IIIIIIDet. 6
38mm18mm38mm32mm
Det. 5
18mmWALLWALL

GSPublisherVersion 183.1.8.100
STEP 98Hang the wall cabinet on the wall by hooking the APC 1 Hangers onto the APC 1 wall plates. SeeDet. 7. Also see Det. 7 for adjustment details.Det. 7
WALL
In-depth AdjustmentVertical AdjustmentSTEP 10After mounting and levelling the cabinet, snap in the APC 1 cover caps to conceal the holes onpanel F. See Det. 8Det. 8
WALL

GSPublisherVersion 183.1.8.100
STEP 129Euro DowelX 4Screw in the Euro Dowels for flipper in the shown positions on panel A and panel B. Their positionscan be adjusted as shown in Det. 9 to change the level of the shelves or to slant the shelves.AECDGHDet. 9FSTEP 11AECDGHFBConnect panel F to panel E as shown. Refer to the holes and/or grooves on the diagram todetermine the panel orientation.

GSPublisherVersion 183.1.8.100
10Insert the shelf (Panel I) as shown. Raise it above the Euro Dowels with the Shelf Supports facingdown. Gently press down the shelf to snap the Euro Dowels into the Shelf Supports, see Fig. 1. Seethe Door Installation guide for further instructions.Fig. 1ACDGHIEFSTEP 14STEP 13Insert the shelf supports for flipper in the shown positions. Confirm that the orientation is as shown inDet. 10 and Det. 11.IDet. 10Det. 11