PG BISON BLUM GOLA FLATPAX KITCHEN User manual

GSPublisherVersion 276.1.7.100
BLUM GOLA FLATPAX KITCHEN RANGEASSEMBLY GUIDEBASE CABINET 900mmDufixMinifix Plinth Leg With Base H100mm Kit4A - Visible Side LeftC - Floor BottomF - BackB - Visible Side RightD - Top RailE - Back RailH - Adjustable ShelfG - BackTOTAL NUMBER OF PANELS: 8HARDWAREPRODUCTQTYScrew 3.5 x 16mm8Wooden Dowel162218Cabinet Connecting Screw Kit4H Profile Backer Connector1Shelf Support Flipper 14mm Kit4IMAGE

GSPublisherVersion 276.1.7.100
2TOOLS REQUIREDScrew Driver(Pozidriv Head)Cordless DrillPozi Bit (PZ2) 1. Confirm that all panels (8) are in the package before assembling. 2. Check the white sticker on each panel for the labelling (A, B, C, D, E, F, G & H). 3. Ensure that the panels are laid on a non-abrasive surface when assembling. 4. Note that all panel connections are done using the system described below.Rubber Mallet8mm Drill Bit2 O'ClockPosition230°PANEL CONNECTION AND FASTENINGGENERAL INSTRUCTIONSDet. 1Det. 2Det. 3IIIIIIIVI - Insert the Minifix (1), Dufix (1) and wooden dowels (2) in the shown positions. Gentlyknock in the wooden dowels using a rubber mallet where necessary.II - Confirm that the Minifix orientation is as shown in Det. 1 then connect the panels.III - Using a screw driver, turn the Minifix 230° clockwise to fasten the panels together. Referto Det. 2.IV - See Det. 3 for Minifix orientation when fastened. Reset the Minifix orientation to thatshown in Det.1 to disconnect the panels.

GSPublisherVersion 276.1.7.100
3Dowel-Dufix-Dowel holes forpanel connectionDowel-Dufix-Dowel holes forpanel connectionCabinet connectionholes for CabinetConnecting Screws.Shelf stud holes forflipper euro dowels.Hinge Plate HolesCabinet connectionholes for CabinetConnecting Screws.Dowel-Dufix-Dowelholes for panelconnectionHinge Plate HolesPILOT HOLES GUIDE FOR SIDE PANELSProvision for J GolaProfileHoles for GolaBracket X

GSPublisherVersion 276.1.7.100
STEP 1STEP 2Connect panels C,D & E to panel A as shown. Refer to the holes and/or grooves on the diagram todetermine the panel orientation.Connect panel B to panels C, D & E as shown. Refer to the holes and/or grooves on the diagramto determine the panel orientation.4AECDCABED

GSPublisherVersion 276.1.7.100
STEP 3STEP 4DFirst, check the diagonal of the cabinet by measuring the two distances indicated by the brokenlines. They should be equal. If not, twist the cabinet accordingly in the diagonal corners as shownuntil an equal value is achieved. After, secure panels F & G to panels E & C respectively as shownusing Screw 3.5 X 16mm.DAF5Screw 3.5 x 16mmX 10BEACBFGGDet. 4IIIIIIFSlide 3mm panel G into the groove on panels A & B with the finished side facing inside thecabinet. Next, insert the H Profile Backer Connector into panel G as shown (See Det. 4). To finish thisstep, slide 3mm panel F through the groove on panels A & B and into the H Profile BackerConnector as shown in Det. 4.GC