PG BISON BLUM FLATPAX User manual

GSPublisherVersion 561.1.8.100
BLUM FLATPAX KITCHEN RANGEASSEMBLY GUIDEBASE CABINET DRAW 1200mmDufixMinifix Plinth Leg With Base H100mm Kit4TOTAL NUMBER OF PANELS: 7HARDWAREPRODUCTQTYScrew3.5x16mm8Wooden Dowel1668Cabinet Connecting Screw Kit4Cantenaria-profile_Silver1IMAGEH Profile Backer Connector1A - Visible Side LeftC - Floor BottomF - BackB - Visible Side RightD - Cantenaria ProfileE - Back RailG - Back1

GSPublisherVersion 561.1.8.100
2TOOLS REQUIREDScrew Driver(Pozidriv Head)Cordless DrillPozi Bit (PZ2) 1. Confirm that all panels (6) are in the package before assembling. 2. Check the white sticker on each panel for the labelling (A, B, C, D, E, F & G). 3. Ensure that the panels are laid on a non-abrasive surface when assembling. 4. Note that all panel connections are done using the system described below.Rubber Mallet8mm Drill Bit2 O'ClockPosition230°PANEL CONNECTION AND FASTENINGGENERAL INSTRUCTIONSDet. 1Det. 2Det. 3IIIIIIIVI - Insert the minifix (1), Dufix (1) and wooden dowels (2) in the shown positions.Gently knock in the wooden dowels using a rubber mallet where necessary.II - Confirm that the minifix orientation is as shown in Det. 1 then connect thepanels.III - Using a screw driver, turn the minifix 230° clockwise to fasten the panelstogether. Refer to Det. 2.IV - See Det. 3 for minifix orientation when fastened. Reset the minifixorientation to that shown in Det.1 to disconnect the panels.

GSPublisherVersion 561.1.8.100
GSPublisherVersion 189.1.8.1003Dowel-Dufix-Dowelholes for panelconnectionHoles forLegrabox/AntaroRunnersCabinet connectionholes for CabinetConnecting Screws.Cabinet connectionholes for CabinetConnecting Screws.Dowel-Dufix-Dowel holes forpanel connectionDowel-Dufix-Dowel holes forpanel connectionHoles for the Cantenaria ProfilePosition1PILOT HOLES KEY FOR SIDE PANELSPosition2Position3Position4Position5Position6Holes forLegrabox/AntaroRunnersHoles forLegrabox/AntaroRunnersHoles forLegrabox/AntaroRunnersHoles forLegrabox/AntaroRunnersHoles forLegrabox/AntaroRunners

GSPublisherVersion 561.1.8.100
GSPublisherVersion 0.1.100.9STEP1STEP2Connect panelsC&Eto panelA as shown.Refer to the holes and/or grooves on the diagram todetermine the panel orientation.Connect panelB to panelsC&E as shown.Refer to the holes and/or grooves on the diagram todetermine the panel orientation.4AECCABE

GSPublisherVersion 561.1.8.100
GSPublisherVersion 189.1.8.100STEP3STEP4First,check the diagonal of the cabinet by measuring the two distances indicated by the brokenlines.They should be equal.If not,twist the cabinet accordingly in the diagonal corners as shownuntil an equal value is achieved.After,secure panelsF&G to panels E&C respectively as shownusingScrew3.5X16mm.AF5Screw3.5x16mmX10BEACBFGGDet.4IIIIIIFSlide3mm panel G into the groove on panelsA&B with the finished side facing inside thecabinet.After,insert the H Profile Backer Connector into panel Gas shown(SeeDet.4).To finishthis step,slide3mm panel Fthrough the groove on panelsA&Band into the H Profile BackerConnectoras shown inDet.4.GC

GSPublisherVersion 561.1.8.100
GSPublisherVersion 561.1.8.100STEP5Fix the cantenaria profile as shown below.Step1;Insert the end cap flush with the profile.(View Det.5). Step 2; Use the screw provided to securely fasten the end dowel to the profileand onto the panel A and panel E.(View Det.6).Step3;Fix the cantenaria profile to the top usingthe special connecting plate.(View Det.7)Fixing plateCantenaria ProfileDet.5Det.6AECFHScrews for fixingclosingcap-dowel.Fixing plateCantenaria ProfileDet.76

GSPublisherVersion 561.1.8.100
GSPublisherVersion 561.1.8.100STEP6STEP77Screw3.5x16mmX12 Plinth Leg With BaseH100mm KitX4Flip the cabinet up-side down as shown.Place the four units of Leg Adjustable Base 100mm in theshown positions,aligning with the pre-drilled pilot holes on panelC.Ensure that the orientation is asshown inDet.4.UsingScrew3.5X16mm,secure the legs onto panelC.Det.4ABCDEFDABCFlip the cabinet upright as shown and level the cabinet byrotating the base of the legs as shown.FGGE

GSPublisherVersion 561.1.8.100
GSPublisherVersion 561.1.8.100STEP8(T123)STEP8(T15)8Connect the rails on panelAas shown usingScrew 3.5mm x 16mm in the predrilled pilot holes.Dothe same,in similar positions,on panelE.OneHeight1and one Height 3 Drawer box go into thiscabinet.CEDAConnect the rails on panelAas shown usingScrew 3.5mm x 16mm in the predrilled pilot holes.Dothe same,in similar positions,on panelE.This cabinet carries a Height1,Height2andHeight3drawer box;one of each.CEDAFig.2Fig.3

GSPublisherVersion 561.1.8.100
GSPublisherVersion 561.1.8.100GSPublisherVersion12.1.99.10STEP8(T222)STEP8(T24)9Connect the rails on panelAas shown usingScrew 3.5mm x 16mm in the predrilled pilot holes.Dothe same,in similar positions,on panelE. One Height 2 andone Height 3 Drawer boxes go into thiscabinet.CEDAConnect the rails on panelAas shown usingScrew 3.5mm x 16mm in the predrilled pilot holes.Dothe same,in similar positions,on panelE.Only Height 2 Drawer boxes (3) go into this cabinet.CEDAFig.4Fig.5

GSPublisherVersion 561.1.8.100
GSPublisherVersion 561.1.8.100GSPublisherVersion12.1.99.10STEP8(T33)STEP910Insert therunners on panelsL&Mof theDrawer box into the rails on panelsA&Eof the BaseCabinet Draw as shown.Push the drawer box in until the face of panelK is flush with the frontedges of panelsA&E.This applies for the different Drawer configurations.Connect the rails on panelAas shown usingScrew 3.5mm x 16mm in the predrilled pilot holes.Dothe same,in similar positions,on panelE.Only Height 3 Drawer boxes (2) go into this cabinet.CEDAEACBLMKONLKNLKNMMFig.6

GSPublisherVersion 561.1.8.100
GSPublisherVersion 12.1.99.10STEP1011First,confirm that the sizes of the drawer fronts correspond with the Drawer Configuration chosen for yourBaseCabinet Draw.Then,connect thedrawer fronts to panelK usingScrew4.0x30mm as shown inFig.7.Refer to Det.6-8for the correct clearances.The vertical space between drawer fronts should be3mm.There should be a1.5mmspace between theleft & right edges of the drawer fronts and theouter faces of panels A & E. This applies for all thedrawer configurations available.Fig.8shows aT222drawer configuration.1.5mm
3mm
Det.6
3mm3mm3mm
Fig.8Det.7Det.8Fig.7