PG BISON KINETIC FLATPAX Series User manual

GSPublisherVersion 98.1.12.100
KINETIC FLATPAX RANGEASSEMBLY GUIDEBASE CABINET 1200mmScrew 4.0 x 50mmC - Back RailE - Visible Side LeftD - Floor BottomF - BackG - Adjustable ShelfA - Visible Side RightB - Top RailH - BackTOTAL NUMBER OF PANELS: 8HARDWARE1PRODUCTQTYScrew 3.5 x 16mm1425Shelf Studs4H Profile Backer Connector1 Plinth Leg With Base H100mm Kit5IMAGE

GSPublisherVersion 98.1.12.100
GENERAL INSTRUCTIONS1. Confirm that all panels (8) are in the package before assembling.2. Check the white sticker on each panel for the labelling (A, B, C, D, E, F,G & H).3. Ensure that the panels are laid on a non-abrasive surface whenassembling.4. Countersink the holes on the side panels before inserting the screws.5. Ensure that the screw is perpendicular to the surface being drilled for aclean and strong joint.2TOOLS REQUIREDScrew Driver(Pozidriv Head)Cordless DrillPozi Bit (PZ2)

GSPublisherVersion 98.1.12.100
STEP 1STEP 2ADBCABCDEConnect panels B, C & D to panel A using Screw 4.0 X 50mm in the pre-drilled pilot holes asshown. Refer to Det 1 - 3 below before fastening the screws.Connect panel E to panels B, C & D using Screw 4.0 X 50mm in the pre-drilled pilot holes as shown.Ensure that the symmetry between panel E and panel A is maintained. Refer to Det 1 - 3.
23mm
0.5mm
23mm
0.5mm0.5mm
1 mm
3Det. 1Det. 2Det. 3Screw 4 x 50mmX 7Screw 4 x 50mmX 7

GSPublisherVersion 98.1.12.100
STEP 3STEP 4BFirst, check the diagonal of the cabinet by measuring the two distances indicated by the brokenlines. They should be equal. If not, twist the cabinet accordingly in the diagonal corners as shownuntil an equal value is achieved. After, secure panels F & H to panels C & D respectively as shownusing Screw 3.5 X 16mm.BEF4Screw 3.5 x 16mmX 10ACEDAFHHDet. 4IIIIIIFSlide 3mm panel H into the groove on panels A & E with the finished side facing inside the cabinet.After, insert the H Profile Backer Connector into panel H as shown (See Det. 4). To finish this step,slide 3mm panel F into the groove on panels A & E and into the H Profile Backer Connector asshown in Det. 4.HD

GSPublisherVersion 98.1.12.100
STEP 5STEP 65Screw 3.5 x 16mmX 15 Plinth Leg With BaseH100mm KitX 5Flip the cabinet up-side down as shown. Place the four units of Leg Adjustable Base 100mm in theshown positions, aligning with the pre-drilled pilot holes on panel D. Ensure that the orientation is asshown in Det. 4. Using Screw 3.5 X 16mm, secure the legs onto panel D.Det. 4AEDBCFBAEDFlip the cabinet upright down as shown and confirm that the legs are secured firmly.FHH

GSPublisherVersion 98.1.12.100
STEP 7STEP 86Insert the Shelf Studs in the shown positions.Slide in panel G as shown, such that it sits on the four shelf studs. The level of the shelf is adjustableby shifting the position of the shelf studs as shown in Det. 5. See Door Installation Guide for furtherinstructions.GDet. 5BEFDAShelf StudsX 4CBEFDACHH