Phanteks AMP GH Series User manual

INSTALLATION GUIDE SUPPORTS
PH-P650GH_01
PH-P750GH_01
PH-P850GH_01
PH-P1000GH_01
PH-P1200GH_01
PH-P1300GH_01
SUPPORT
US & Canada
[email protected]
International
[email protected]
FOLLOW US
SOCIAL MEDIA
Instagram
Phanteks
Facebook
Phanteks
YouTube
Phanteks
Twitter
@phanteks
Cable Type Connectors per Cable Length per Cable (mm)
Motherboard 24-PIN 1 610
CPU EPS 4+4-PIN 1 650
PCIe 6+2-PIN 1 750
12VHPWR 12+4-PIN 1 720
SATA 4 450 -150 |150 |150
SATA |Molex 2 |2 450 -150 |150 |150
C13 Power Cable 1 1500
Accessories Included
User Manual
Installation Guide
PSU Bag
Cable Bag
Ziptie Bag
Screw Pack
CPU
4+4-PIN
SATA |MOLEX
C13 POWER CABLE
SATA
PCIe
6+2-PIN
12VHPWR
12+4-PIN
ACCESSORIES INCLUDED
CABLES INCLUDED
POWER SUPPLY
AMP GH
MANUAL
WARRANTY CABLE BAG
SCREW PACKZIP TIE BAG
MOTHERBOARD
24-PIN
* The amount of cables may vary depending on model.

INSTALL PSU INTO CHASSIS
01 CONNECT CABLES TO PSU 02
INSTALLATION GUIDE
Secure the power supply with the 4x included PSU screws. Check the PC
chassis manual for more installation details.
Connect all needed cables to the power supply according to the overview
below. The exact connector lay-out and quantity may be different depending
on the model.
* Connectors may vary depending on model.
* The amount of cables may vary depending on model.
12VHPWR GPU CONNECTOR
04
CONNECT POWER CABLE
05
HYBRID FAN MODE
06
BE SAFE!
07
CONNECT CABLES TO SYSTEM COMPONENTS
03
The AMP GH is equipped with the 12VHPWR PCIe Gen5 GPU connector and
cable. Note that a compatible GPU is required.
The maximum power output depends on your AMP GH model:
Connect the power cable to the power supply and a
grounded power outlet respectively. Make sure the power
supply is turned off ‘O’ before connecting it to a power outlet.
Use the Hybrid Fan Mode to unlock the 0RPM fan speed when under 30%
load. This will make the power supply absolutely silent under low load and
temperature levels.
Hybrid Fan Mode is turned on when the button is pressed in, and off when
pressed again.
Switch the power button to the ‘I’ position to turn on your system.
When making any changes to the hardware, be sure that the power button
is switched from the ‘I’ to the ‘O’ position so the power supply is turned off.
Only use Phanteks cables that are provided with the power supply. If there
are any questions, please don’t hesitate to visit www.phanteks.com/FAQ for
more details.
Phanteks will not take responsibility for any damages incurred due to incorrect installation or usage
of this product.
Connect all power cables to the corresponding system components, please
follow the manufacturers instructions for additional information.
Pre-connect all needed cables to the
PSU before installing it into the chassis.
See step 2
PRO TIP
AMP Model Output Watts
GH 1200 Up to 600
GH 1000 Up to 600
GH 850 Up to 450
GH 750 Up to 450
GH 650 Not available
12VHPWR
12+4-PIN CABLE
12VHPWR
12+4-PIN
MOLEXSATAPCIe
6+2-PIN
CPU
4+4-PIN
MOTHERBOARD
24-PIN
PSU
PSU SCREW
INSTALL
4x
MOTHERBOARD
10+18-PIN
CPU |PCIe
8-PIN
12VHPWR
12+4-PIN
SATA |MOLEX
6-PIN