Philips 63059CM Original operating instructions

Strand Lighting Inc.
6603 Darin Way, Cypress, CA 90630, USA
Tel: [phone] Fax: [phone]
Strand Lighting Europe Ltd.
Unit 2, Royce Road, Fleming Way, Crawley, West Sussex. United Kingdom
Tel: [phone] Fax: [phone]
Strand Lighting Asia
Room 6-10, 20/F Delta House 3 On Yiu Street, Shatin, N.T. Hong Kong
Tel: [phone] Fax: [phone]
www.strandlighting.com
The material in this manual is for information purposes only and is subject to change without notice.
Strand Lighting assumes no responsibility for any errors or omissions which may appear in this manual.
For comments and suggestions regarding corrections and/or updates to this manual, please contact your
nearest Strand Lighting office.
El contenido de este manual es solamente para información y está sujeto a cambios sin previo aviso.
Strand Lighting no asume responsabilidad por errores o omisiones que puedan aparecer. Cualquier
comentario, sugerencia o corrección con respecto a este manual, favor de dirijirlo a la oficina de Strand
Lighting más cercana.
Der Inhalt dieses Handbuches ist nur für Informationszwecke gedacht, Aenderungen sind vorbehalten.
Strand Lighting uebernimmt keine Verantwortung für Fehler oder Irrtuemer, die in diesem Handbuch
auftreten. Für Bemerkungen und Verbesserungsvorschlaege oder Vorschlaege in Bezug auf Korrekturen
und/oder Aktualisierungen in diesem Handbuch, moechten wir Sie bitten, Kontakt mit der naechsten
Strand Lighting-Niederlassung aufzunehmen.
Le matériel décrit dans ce manuel est pour information seulement et est sujet à changements sans préavis.
La compagnie Strand Lighting n'assume aucune responsibilité sur toute erreur ou ommission inscrite dans
ce manuel. Pour tous commentaires ou suggestions concernant des corrections et/ou les mises à jour de ce
manuel, veuillez s'll vous plait contacter le bureau de Strand Lighting le plus proche.
Information contained in this document may not be duplicated in full or in part by any person without
prior written approval of Strand Lighting Inc. Its sole purpose is to provide the user with conceptual
information on the equipment mentioned. The use of this document for all other purposes is specifically
prohibited. Certain features of the equipment described in this document may form the subject of patents
or patent applications.
Document Number: 2-450207-010
Version as of: May 21, 2009
Vision.net Ceiling Occupancy Sensor Installation & Operation Guide
©2009 Philips Group. All rights reserved.

Vision.net Ceiling Occupancy Sensor Installation & Operation Guide
1
Important Safeguards
When using electrical equipment, basic safety precautions should always be followed
including the following:
a. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b. Do not use outdoors.
c. Do not mount near gas or electric heaters.
d. Equipment should be mounted in locations and at heights where it will not
readily be subjected to tampering by unauthorized personnel.
e. The use of accessory equipment not recommended by the manufacturer
may cause an unsafe condition.
f. Do not use this equipment for other than intended use.
g. Refer service to qualified personnel.
SAVE THESE INSTRUCTIONS.
WARNING: You must have access to a main circuit breaker or other power
disconnect device before installing any wiring. Be sure that power is disconnected
by removing fuses or turning the main circuit breaker off before installation.
Installing the device with power on may expose you to dangerous voltage and
damage the device. A qualified electrician must perform this installation.
WARNING: Refer to National Electrical Code® and local codes for cable
specifications. Failure to use proper cable can result in damage to equipment or
danger to persons.
CAUTION: Wire openings MUST have fittings or lining to protect wires/cables
from damage. Use 90° C copper wire only!

Installation & Operation Guide Vision.net Ceiling Occupancy Sensor
2
TABLE OF CONTENTS
Preface ....................................................................................................................................... 3
About this Guide ...............................................................................................................3
Description ........................................................................................................................3
Installation .................................................................................................................................4
Mounting ........................................................................................................................... 4
Wiring ............................................................................................................................... 5
Sensor Programming with Vision.net Designer Software ........................................................ 6
Sensor Programming with Remote ...........................................................................................6
Programming Ceiling Occupancy Sensor .................................................................................7
Mode ................................................................................................................................. 7
Time ..................................................................................................................................8
Relays Select .....................................................................................................................9
Sensitivity ........................................................................................................................ 10
Photocell Sensitivity ....................................................................................................... 11
Miscellaneous ..................................................................................................................11
Test .................................................................................................................................. 12
Display ............................................................................................................................ 12
Manual Configuration ............................................................................................................. 13
Using Programming Switches .........................................................................................13
LED Display ................................................................................................................... 13
Troubleshooting Guide ...........................................................................................................15

Vision.net Ceiling Occupancy Sensor Installation & Operation Guide
3
PREFACE
About this Guide
The document provides programming and installation instructions for the following Vision.net
products:
• 63059CM - Vision.net Ceiling Occupancy Sensor
• 63059HB - Vision.net High Bay Ceiling Occupancy Sensor
Please read all instructions before installing or using this product. Retain this guide for future
reference.
IMPORTANT INFORMATION. PLEASE READ!
This unit is intended for installation in accordance with the National Electric Code® and local
regulations. It is also intended for permanent installation in indoor applications only. Before
any electrical work is performed, disconnect power at the circuit breaker or remove the fuse to
avoid shock or damage to the control. It is recommended that a qualified electrician perform
this installation.
Description
Vision.net Ceiling Occupancy Sensors (63059CM, 63059HB)
The Vision.net Low-Voltage Ceiling Occupancy Sensor is a
multiple technology, occupancy-sensing low-voltage device that is
designed for use with a Vision.net architectural control system.
Each sensor may be programmed to act as a Vision.net button (like
Preset, Preset/Off, Toggle, Smart, Console) providing the ability to
execute any Vision.net command across the architectural control
network.
Vision.net Programmer Remote (63063)
The Vision.net Programmer Remote is an optional accessory which
provides quick and easy access to the full range of Occupancy
Sensor features.
TEST
PGM /
SELECT
ABCD
EFGH
1234
567 8
09
MODE
MODE
TIME
TIME
RLYS
RLYS
SENS
PHSET
PHON
DSCN
MISC
MISC
AI / 1
DH1
LSUN
NI / 3
DH2
HSUN
CI / 5
LMAIN
TM / 10
MO / 15 AO / 20 FM / 25 FA / 30
DH-MO
-SUN
DH-AO
=SUN +SUN
DEFAULT DISPLAY
SETTINGS
S
W
#
S
W
M
R
O
N
R
O
F
F
S
C
N
T
A
P
D
T
A
P
O
V
R
D
I
O
V
R
T
G
L
DIM
DIM
MSTR
LASER FIELD
FIELD
SETTINGS
EXIT
DH3 DH4
82-2533
R
K
P
D
Sensor
Remote

Installation & Operation Guide Vision.net Ceiling Occupancy Sensor
4
INSTALLATION
Mounting
The Ceiling Occupancy Sensor may be mounted in a junction box or directly to the ceiling
depending on local code. The unit must have an unobstructed view of the area to be
monitored. If the unit is subject to "false triggering" from activity beyond the desired area of
coverage, a portion of the lens may be masked to achieve the desired response. Simply install
the Field of View Customizing Template (provided).
To install:
Step 1. Check for any obstructions located behind the desired mounting location.
Step 2. Drill 1-1/2" hole in the desired mounting location.
Step 3. Place Ceiling Occupancy Sensor through the hole and secure with supplied washer
and locknut.
Step 4. The lens may be removed to install the Field of View Customizing Template.
Simply rotate the lens cover slightly counter-clockwise and remove.
Step 5. Trim the template for the desired effect and install on interior of the lens. (Careful
placement of the template is necessary to ensure proper function.)
Step 6. Replace lens cover and verify that the unit is securely mounted.
Figure 1: Installing Ceiling Occupancy Sensor
RETAINING NUT
WASHER
LOW VOLTAGE
WIRES (4)

Vision.net Ceiling Occupancy Sensor Installation & Operation Guide
5
Wiring
Ceiling Occupancy Sensors should be connected to an AV Interface Board (63065).
To connect wiring:
Step 1. If conduit is required by local code, route low voltage wiring into adjacent junction
box and secure with included 1/2" nipple.
Step 2. Connect low voltage network to AV Interface Board with (4) #18 AWG wires
according to the wiring diagram below.
Note: Up to eight (8) Occupancy Sensors may be linked in parallel.
Figure 2: Connecting Low Voltage Wiring
RED (+12VDC)
BLACK (-12VDC GROUND)
WHITE/GREEN (DATA+)
GREEN (DATA -)
J4 1 Black
2 Green
3 White/Green
4 Red
63065 AV Interface Board

Installation & Operation Guide Vision.net Ceiling Occupancy Sensor
6
SENSOR PROGRAMMING WITH VISION.NET
DESIGNER SOFTWARE
Ceiling Occupancy sensors may be programmed with Strand Lighting’s Vision.net Designer
software, as part of a Vision.net architectural controls system. This software (and its manual)
may be downloaded from www.strandlighting.com.
SENSOR PROGRAMMING WITH REMOTE
A Vision.net Occupancy Sensor Remote Programmer (optional accessory) can be used to
program the unit(s). Please note that configuration changes made with the Remote
Programmer will not be saved in the Vision.net Designer software configuration file.
To enter Programming Mode:
Step 1. Aim the remote at the Ceiling Occupancy Sensor and press
the PGM (Program) button. All affected sensors will blink
red.
Step 2. You may now select which sensor you would like to program
by "laser painting" it with the remote laser. Press and Hold the
LASER button and allow the Laser beam "hit" the sensor you
want to select. Once the signal is received, the sensor will
illuminate green and is ready to receive commands.
To change sensor parameters, first select the "field" that you would like
to change. Programming fields include: Mode, Time, A/V Interface,
Sensitivity, and Photocell Sensitivity. The following sections will
explain each mode.
To change the selected device(s) to be programmed:
To select devices for programming, use the FIELD/SELECT button or
individually select them using the LASER button. The FIELD/SELECT
feature allows selection of devices to be programmed (singular
occupancy, all occupancy, switches, or dimmers/photocells). The
devices always starts in Single Occupancy Mode.
Step 1. Enter Programming Mode. (Refer to previous section.)
Step 2. Press FIELD/SELECT button to toggle through modes:
Blue = Single Occupancy Sensor
Blue/Red = All Occupancy Sensors on network
Red or Green = reserved for future use
Note: When the sensor is blue or blue/red, additional occupancy sensors may be selected or
removed by "laser painting" them with the laser (LASER button).
Figure 3:
Remote Layout
TEST
PGM /
SELECT
ABCD
EFGH
1234
567 8
09
MODE
MODE
TIME
TIME
RLYS
RLYS
SENS
PHSET
PHON
DSCN
MISC
MISC
AI / 1
DH1
LSUN
NI / 3
DH2
HSUN
CI / 5
LMAIN
TM / 10
MO / 15 AO / 20 FM / 25 FA / 30
DH-MO
-SUN
DH-AO
=SUN +SUN
DEFAULT DISPLAY
SETTINGS
S
W
#
S
W
M
R
O
N
R
O
F
F
S
C
N
T
A
P
D
T
A
P
O
V
R
D
I
O
V
R
T
G
L
DIM
DIM
MSTR
LASER FIELD
FIELD
SETTINGS
EXIT
DH3 DH4
82-2533
R
K
P
D

Vision.net Ceiling Occupancy Sensor Installation & Operation Guide
7
PROGRAMMING CEILING OCCUPANCY SENSOR
Ceiling Occupancy Sensor programming is the same for both single, multiple and all sensors
on the network. Programming selections will affect all illuminated sensors.
Mode
The MODE field allows access to intelligence level, Automatic or Manual On, and reset to
factory default.
The Occupancy Sensor time-off delay can operate in four different modes. The default is
Fixed Time Mode, which means the fixed time delay (as set by the user) is always used. The
other three modes allow the sensor to automatically adjust to the space and occupancy
patterns, differing in how aggressive the sensor is with saving energy. Conservative Mode will
automatically adjust the time-off between 5 to 30 minutes. Normal Mode will automatically
adjust the time-off between 3 and 15 minutes for enhanced energy savings. Aggressive Mode
will automatically adjust the time-off delay between 1 minute and 3 minutes for maximum
energy savings.
The Occupancy Sensor can be configured to operate in either a Manual On or Automatic On
Mode. In Manual On Mode, the lights will only turn on when a designated switch activates the
relay. The lights will turn off automatically when vacancy is detected for the time delay
period. In the Automatic On Mode, the lights will automatically turn on as soon as occupancy
is detected. The lights will turn off when either the designated switch deactivates the relay or
automatically when vacancy is detected for the time delay
To change the mode of the sensor:
Step 1. Enter Programming Mode (refer to page 6.)
Step 2. Press MODE button.
Step 3. Select intelligence level:
Step 4. Select activation mode:
Exit programming by pressing the PGM (Program) button or continue with programming by
selecting another field.
Button 1 Aggressive Intelligence
Button 2 Normal Intelligence
Button 3 Conservative Intelligence
Button 4 Fixed Timing * Factory Default
Button 5 Manual ON
Button 6 Automatic ON * Factory Default
Button 7 Factory Default Manual ON Press and hold for 3 or more sec-
onds to factory default all settings.
Button 8 Factory Default Automatic ON
Button 0 Factory Default * Fixed Timing & Automatic

Installation & Operation Guide Vision.net Ceiling Occupancy Sensor
8
Time
The TIME field allows selection of the time-out period after the sensor no longer detects
occupancy. Periods may be selected from 1 to 30 minutes.
Note: Increasing the time delay will lower the possibility of a false Off trigger, but will also
lower the energy savings.
To change the time of the sensor:
Step 1. Enter Programming Mode
(refer to page 6.)
Step 2. Press TIME button.
Step 3. Select time-out period by
pressing the appropriate
button.
Exit programming by pressing the
PGM (Program) button or continue
with programming by selecting
another field.
Button 1 1 Minute
Button 2 3 Minutes
Button 3 5 Minutes
Button 4 10 Minutes
Button 5 15 Minutes * Factory Default
Button 6 20 Minutes
Button 7 25 Minutes
Button 8 30 Minutes
Button 0 Factory Default * 15 minutes

Vision.net Ceiling Occupancy Sensor Installation & Operation Guide
9
Relays Select
The RLYS (Relays) Select Button is used to program which Relays are controlled by the
Occupancy Sensor (when used with Contact Relay Packs). One or more Relays can be
programmed into the Sensor. The factory default is All Relays (1-8). The Sensor can also be
used to trigger a specific button on a connected keypad. When used with a Button Station, the
Relay programmed into the Sensor will define which button on the keypad to activate.
Detected motion will trigger the button 'Press On' action. The end of motion timeout will
trigger the button "Release" action. When All Relays are selected (factory default), the
connected keypad will trigger only Button 1. Only single Relay selects are allowed when
triggering keypads.
To change the relay/button selection of the sensor:
Step 1. Enter Programming Mode (refer to page 6.)
Step 2. Press RLYS button.
Step 3. Select the button to be controlled by the sensor.
Exit programming by pressing the PGM (Program) button or continue with programming by
selecting another field.
Button 1 Relay/Button #1 * Factory Default
Button 2 Relay/Button #2 * Factory Default
Button 3 Relay/Button #3 * Factory Default
Button 4 Relay/Button #4 * Factory Default
Button 5 Relay/Button #5 * Factory Default
Button 6 Relay/Button #6 * Factory Default
Button 7 Relay/Button #7 * Factory Default
Button 8 Relay/Button #8 * Factory Default
Button 0 Factory Default * Current mode only

Installation & Operation Guide Vision.net Ceiling Occupancy Sensor
10
Sensitivity
Part of the superior performance of the Ceiling Occupancy Sensor involves the increased
sensitivity of the sensor system. The three settings are Low, Medium, and High. Each
application may be slightly different and the preferences of each user might be different. The
default setting (Medium) will be adequate for most situations. The settings are described as
follows:
Low: Lowest level of detection setting - when less detection is required - occupants are close
to the sensor or movements within the space are more pronounced. This level may result in
lights turning off with reduced activity.
Medium (default): Default setting - medium level of detection to fit most applications.
High: Highest level of detection - movements and activity within the space are less
pronounced. This level increases the possibility of false triggering.
To change the sensitivity selection of the sensor:
Step 1. Enter Programming Mode
(refer to page 6.)
Step 2. Press SENS button.
Step 3. Select the desired level of
sensitivity.
Exit programming by pressing the PGM (Program) button or continue with programming by
selecting another field.
Button 1 Low
Button 2 Medium * Factory Default
Button 3 High
Button 0 Factory Default * Medium

Vision.net Ceiling Occupancy Sensor Installation & Operation Guide
11
Photocell Sensitivity
There is a photo eye (photocell) in the sensor which can prevent the sensor from automatically
turning on the lights if the light level in the room is already higher than a set level. This feature
can be enabled or disabled - with the factory default being disabled.
The PHOTOCELL SENSITIVITY field allows selection of the internal photocells sensitivity
levels, as well as disable.
To change the sensitivity selection of the photocell:
Step 1. Enter
Programming
Mode (refer to
page 6.)
Step 2. Press PHON
button.
Step 3. Select the desired
level of sensitivity.
To let the unit "capture" the
present room ambient, press and hold button 8 for 3-4 seconds. The unit will turn off the
lights, take a snapshot of the current room ambient, and then turn the lights back on.
Exit programming by pressing the PGM (Program) button or continue with programming by
selecting another field.
Miscellaneous
The MISC field allows the audible buzzer and/or the complete occupancy sensor to be enabled
or disabled.
To activate/deactivate the audible buzzer or entire occupancy sensor:
Step 1. Enter Programming Mode (refer to page 6.)
Step 2. Press MISC button.
Step 3. Select desired parameters:
Button 1 Enable Buzzer * Factory Default
Button 2 Disable Buzzer
Button 7 Enable Sensor * Factory Default
Button 8 Disable Sensor
Button 0 Factory Default * Enable buzzer & sensor
Button 1 Low Ambient
Button 2 Low-Medium Ambient
Button 3 Medium-Low Ambient
Button 4 Medium Ambient
Button 5 Medium-High Ambient
Button 6 High-Medium Ambient
Button 7 High Ambient
Button 8 Disabled * Factory Default
Button 0 Factory Default * Disabled

Installation & Operation Guide Vision.net Ceiling Occupancy Sensor
12
Test
The Test feature allows testing of the system without having to wait extended periods of time
for the loads to time out.
While in Test Mode, the timer functions at a rate of 1 second per 1 minute of decay. For
example, a 30-minute time-out period would become a 30-second time-out period. There is a
10 second minimum.
During testing, the sensor will blink RED to indicate it is in the Test Mode, BLUE when it
detects motion, and GREEN when it is timing out.
To enter Test Mode:
Step 1. Enter Programming Mode (refer to page 6.)
Step 2. Press TEST button. All sensors in Test Mode will blink red.
Step 3. Confirm all sensors, relays and switches are working properly.
Step 4. Press TEST button again to exit Test Mode.
Note: You may alternate between Test Mode and Programming Mode by simply pressing the
TEST button anytime during the process.
Display
The Display feature allows the programmer to visually and audibly verify the programmed
feature parameters.
To enter Display Mode:
Step 1. Enter Programming Mode (refer to page 6.)
Step 2. Select the field you wish to verify.
Step 3. Press DISPLAY SETTINGS button.
Step 4. Tap the button for each available setting for the chosen field. The sensor will blink
RED indicating that the setting is not programmed for the sensor, or BLUE,
indicating that the setting is programmed to the sensor.
Step 5. Press DISPLAY SETTINGS button again to exit.
Example: To see the time-out period of a sensor: Press TIME, then DISPLAY SETTINGS.
Toggle through the time selections until the sensor blinks BLUE to indicate the programmed
time-out period.

Vision.net Ceiling Occupancy Sensor Installation & Operation Guide
13
MANUAL CONFIGURATION
Using Programming Switches
There are two programming switches (buttons) on the Ceiling Occupancy Sensor which can be
used to Display and Modify the Sensor’s Settings. Programming Switch 2, the "Field" Button
(turns on the Blue LED when pressed) is used to select the Field you wish to display or
modify. Programming Switch 1, the "Setting" Button (turns on the Green LED when pressed)
is used to set the value of the selected Field. By using both buttons, the Sensor can be
manually configured for most applications.
To enter Manual Programming Mode:
Step 1. Unscrew Lens Cover on Ceiling
Sensor to access manual
programming buttons.
Step 2. Press and hold the Field Button for 3
seconds. After 3 seconds the Red
LED will turn on indicating the unit
is in the Manual Programming
Mode. Release the button.
To exit Manual Programming Mode:
There are three ways to exit the Programming
Mode.
• Keep tapping the Field Button until
Ceiling Sensor exits Programming Mode.
• Hold the Field Button for 3 seconds.
• Stop tapping the buttons. The Ceiling
Sensor will exit the Programming Mode 1 minute after the last button press.
LED Display
When in the Programming Mode, the LEDs display the following information:
• Red LED – Always On.
• Blue LED – Blinks 1 to 6 times to indicate the Field being displayed or set (see Field/
Setting Table on next page).
• Green LED – Blinks 1 to 9 times to indicate the present setting of the Field (see Field/
Setting Table on next page).
Programming
Switch 1 (Setting)
GREEN
Programming
Switch 2 (Field)
BLUE
Figure 4: Manual Programming Buttons

Installation & Operation Guide Vision.net Ceiling Occupancy Sensor
14
Field/Setting Table:
* Factory Default
To set a Fiel d:
Step 1. After entering the Programming Mode, the Field LED (Blue) will blink one time
(Mode Set), display the present setting (Green blinks), and then repeat the pattern.
Step 2. Each press of the Field Button will select the next Field.
Step 3. Pressing the button after the last field will exit the Programming Mode.
Step 4. Once the Field is selected (proper number of Blue blinks), press the Setting Button
one or more times to change the Field setting. Verify by observing the number of
blinks.
Step 5. You can select the factory default by pressing and holding the Setting Button for 3
seconds.
Notes:
Each tap of the Setting Button will advance the setting by one. Example: Three taps sets the
Field setting to 3 (taps must be less then 2 seconds apart).
After 2 or more seconds following the last tap, the Setting Button will reset back to 1 with the
next tap. Example: Three taps, delay of 2 or more seconds, and then two taps will set the Field
setting to 2.
To set Factory Default for All Fields:
When entering the Programming Mode, instead of holding the Field Button for 3 seconds,
hold it for 10 seconds. After 10 seconds the Sensor will reset the Fields back to Factory
Default, buzz long, and exit the Programming Mode.
Blue Blinks - Field Green Blinks - Setting
1 - Mode 1 - Aggressive Intelligence
2 - Normal Intelligence
3 - Conservative Intelligence
4- Fixed Timing*
2 - Manual/Automatic 1 - Manual, 2 - Automatic*
3 - Time 1 - 1 min, 2 - 3 min, 3 - 5 min, 4 - 10 min
5 - 15 min*, 6 - 20 min, 7 - 25 min, 8 - 30 min
5 - Sensitivity 1 - Low, 2 - Medium*, 3 - High
6 - Photocell On Sensitivity 1 - Low, ...7 High, 8 - Disabled*

Vision.net Ceiling Occupancy Sensor Installation & Operation Guide
15
TROUBLESHOOTING GUIDE
The following troubleshooting guide addresses common issues.
Symptom Cause Correction
Lights do not come on either
manually or automatically.
Lamp(s) are burned out or
missing.
Replace lamp(s) in fixture(s).
Circuit breaker if Off. Turn On circuit breaker.
Lights do not come on auto-
matically.
Sensor is in Manual Mode. Use Manual Mode if local or
installation requires.
Reconfigure sensor to Automatic
Mode, if allowed.
Lights are On all the time. Sensor sensitivity setting not
appropriate.
Lower sensor sensitivity.
Wire connections are faulty. Recheck all wire connections.
IMPORTANT! Turn off circuit
breaker before servicing.
Shorted or damaged device. Replace sensor with new unit.
Remote does not turn on
lights.
Wire connections are faulty. Recheck all wire connections.
IMPORTANT! Turn off circuit
breaker before servicing.
Occupancy outside the
desired space triggers sen-
sor.
Non-ideal placement or no
mask is being used.
Use proper masking to mask
unwanted areas.
Sensor sensitivity setting not
appropriate.
Lower sensitivity setting.
No audible warnings before
lights turn off.
Audible warning is disabled. Enable audible warning tones.
Lights turn off, even though
room is occupied.
Insufficient movement, fre-
quency or amount.
Increase Time Out or increase
sensor sensitivity.
Lights remain on too long
when room is unoccupied.
Time Off delay too long. Decrease Time Off delay or set
Logic/Timer Mode accordingly.

Installation & Operation Guide Vision.net Ceiling Occupancy Sensor
16
NOTES

Vision.net Ceiling Occupancy Sensor Installation & Operation Guide
17
NOTES

Part No. 2-450207-010