Philips CEM250 User manual

Register your product and get support at
CEM250_55
CEM250/55
© 2008 Koninklijke Philips Electronics N.V.
All rights reserved.
Document order number:
EN User manual 3

3
7 Adjust sound 21
Adjust volume 21
Turn Dynamic Bass Boost (DBB) on/off
21
Select preset equalizer 21
Other sound settings 21
8 Adjust system settings 22
Set PIN code 22
Set bluetooth connection 22
Select blackout setting 22
Turn demo mode on/off 22
Change button backlight color 22
Select start volume 22
Turn beep sound on/off 23
Turn display scroll on/off 23
Reset 23
9 Additional information 24
Detach the front panel 24
Replace fuse 24
Remove the unit 24
Connect external sound source 24
10 Product information 25
11 Troubleshooting 27
12 Glossary 28
Contents
1 Important 4
Safety 4
Notice 4
2 Your Car Audio System 6
Introduction 6
What’s in the box 6
Overview of the main unit 7
Overview of the remote control 8
3 Get started 10
Install the car audio 10
Install remote control battery 15
Turn on 15
Set clock 15
4 Listen to radio 16
Tune to a radio station 16
Store radio stations in memory 16
Tune to a preset station 16
5 Use bluetooth devices 17
Pairing bluetooth devices 17
Play audio les 17
Voice dialing 17
Make a call 17
Call waiting 17
Call transfer 17
Terminate call 17
6 Playaudioles  18
Play a disc 18
Play from USB/SD/MMC device 18
Control play 19
Search for an MP3/WMA track 19
View play information 19
Random play 19
Repeat play 20
Intro play 20
Select shock-protect setting 20
English
EN

6
7
a
c
g h
i j
d e f
ba
c
g h
i j
d e f
b
2 Your Car Audio
System
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.Philips.com/welcome.
Introduction
With the in-car audio system, you can enjoy
your drive while you listen to:
FM or AM (MW) radio
Audio from CD or MP3 disc
Audio from your mobile phone
Audio from a USB drive
Audio from a SD/MMC card
Audio from external devices
Besides, you can dail number, answer and hang
up a call on the audio system.
What’s in the box
Check and identify the contents of your
package:
aCar audio system
bRemote control
cMicrophone
dMicrophone hold
eRubber cushion
fDisassembly tool (2 pieces)
gFront panel
hCarrying case for front panel
iTrim plate
jScrew (4 pieces)
•
•
•
•
•
•
d/MUTE
Turn the unit on or off.
Adjust volume.
Conrm selection.
Enter characters for search.
Dial phone number.
Mute or unmute the volume.
eMENU / DISP
Display radio frequency, clock and
radio program type (if available).
Display track, elapsed time, artist,
alburm, title, folder, le and clock.
Access system menu.
f
Return to previous menu.
Stop search.
•
•
•
•
•
•
•
•
•
•
•
Overview of the main unit
a(green/red)
Answer phone (green)
Dial number (green)
View call log (green)
Terminate call (red)
b/ DBB
Select tuner band.
Select MP3/WMA folder.
Scroll up menu.
Turn on or off Dynamic Bass Boost
(DBB) sound.
cSOURCE
Select audio source.
•
•
•
•
•
•
•
•
•
abdghi ef
s
xwut v
r q p o n m l k j
c abdghi ef
s
xwut v
r q p o n m l k j
c
EN
English
EN

8
9
wRESET
Restore default settings
xSD/MMC card slot
Overview of the remote
control
a/
Tune for radio station
Skip/search for a track.
b
•
•
•
a
c
d
e
f
g
b
k
m
n
p
q
r
s
o
j
l
h
i
t
u
a
c
d
e
f
g
b
k
m
n
p
q
r
s
o
j
l
h
i
t
u
Disable screen blackout.
gDisplay panel
h
Unlock the panel
iUSB socket
jExternal equipment socket
k6
Select preset station no. 6
l5
Select preset station no. 5
mSHUF, 4
Set shufe play mode.
Select preset station no. 4
n3, REP
Set repeat play mode.
Select preset station no. 3
oINTRO, 2
Turn intro play on or off.
Select preset station no. 2
p1,
Start play
Pause or resume play.
Select preset station no. 1
q/
Tune for radio station
Skip/search for MP3/WMA track.
rEQ/Audio
Select equalizer (EQ) setting.
Access audio setting menu.
s/SEARCH
Select tuner band.
Store radio stations automatically.
Scroll up or down menu.
Select MP3/WMA folder.
Search a track or folder.
tPanel power connection
uDisc slot
v
Take disc out.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
qSEARCH
Set radio station memory
automatically.
Search a track or folder.
rDISP
Display radio frequency, clock and
radio program type (if available).
Display MP3/WMA elapsed time, last
listened radio frequency, and clock.
s
Terminate call
t3, REP
Set repeat play mode.
Select preset station no. 3
Enter phone number.
uINTRO, 2
Turn intro play on or off.
Select preset station no. 2
Enter phone number.
•
•
•
•
•
•
•
•
•
•
•
Mute or restore volume.
cPWR
Turn the unit on or off.
dMENU
Access system menu.
eAUDIO
Access audio setting menu.
f5/6/7/8/9/0+
Select track or preset radio station.
Enter phone number.
g
Answer phone.
Dial number.
h1,
Start play from the beginning of the
rst track.
Pause or resume play.
Select preset station no. 1.
Enter phone number.
iSHUF, 4
Set shufe play mode.
Select preset station no. 4.
Enter phone number.
jSEL
Conrm selection.
k/
Tune for radio station
Skip/search for MP3/WMA track.
l
Return to previous menu.
Disable screen blackout.
mSOURCE
Select audio source
nVOLUME +/-
Adjust volume.
oEQ
Select EQ setting.
pDBB
Turn on or off Dynamic Bass Boost
(DBB) sound.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
EN
English
EN

10
11
When you connect other devices to this
unit, ensure that the rating of the car circuit
is higher than the total fuse value of all the
connected devices.
Notes on speaker connection
Never connect speaker wires to the metal
body or chassis of the car.
Never connect speaker wires with stripes
to one another.
Overview of parts
These are the supplied parts needed to
connect and install this unit.
aIn-car audio system
bSleeve
cFront panel
dTrim plate
eRubber cushion
fDisassembly tools
gScrews 4 pieces
•
•
•
a b
c
e f g
d
a b
c
e f g
d
3 Get started
Caution
Use the controls only as stated in this user manual.•
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for
the model and serial number of your unit.The
model number and serial number are on the
bottom of your unit.Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Install the car audio
These instructions are for a typical installation.
However, if your car has different requirements,
make the corresponding adjustment. If you have
any questions regarding installation kits, consult
your Philips car audio dealer.
Caution
This unit is designed for negative ground (earth) 12V
DC operation only.
Always install this unit in the car dashboard. Other
locations can be dangerous as the rear of the unit heats
up during use.
To avoid short-circuit: before you connect, ensure that
the ignition is off.
Ensure that you connect the yellow and red power
supply leads after all other leads are connected.
Ensure that all loose leads are insulated with electrical
tape.
Ensure that the leads do not get caught under screws
orin parts that will move (e.g. seat rail).
Ensure that all ground (earth) leads are run to a
common ground (earth) point.
Use only the supplied mounting hardware for a safe
and secure installation.
Improper fuses can cause damage or re. When you
need to change the fuse, consult a professional.
•
•
•
•
•
•
•
•
•
Note on the power supply lead (yellow)
Connector Connect to
1 MIC Microphone
2 REAR LINE
OUT R
Rear right
speaker
3 REAR LINE
OUT L
Rear left speaker
4 SUB OUT Subwoofer
5 ANTENNA Antenna
Connect wires: for cars without ISO
connectors
Caution
Be sure to connect the black ground (earth) lead rst.•
1 Connect the antenna and amplier as
illustrated, if applicable.
A1 A2 A3 A4 A5 A6 A7 A8
B1 B2 B3 B4 B5 B6 B7 B8
A
A
B
a b c d e
A1 A2 A3 A4 A5 A6 A7 A8
B1 B2 B3 B4 B5 B6 B7 B8
A
A
B
a b c d e
Connect wires: for cars with ISO
connectors
Caution
Ensure that all loose leads are insulated with electrical
tape.
•
1Pull out the ISO connectors from car
dashboard and connect them to the bigger
end of the supplied standard connector.
2Connect the other end of the supplied
standard connector to the unit.
3 Connect the antenna and amplier as
illustrated, if applicable.
EN
English
EN

12
13
1 Green/black strip Left speaker
(Rear)
2 White/black strip Left speaker
(Front)
3 Gray/black strip Right speaker
(Front)
4 Purple/black strip Right speaker
(Rear)
e RED Ignition key +12V DC
when ON/ACC
f BLUE Motor/electric antenna
relay control lead/
Amplierrelaycontrol
lead
g BLACK Ground
h ORANGE/
WHITE
Illumination switch
i YELLOW To the +12V car
battery which is
energized at all times
B
b
a
c
d
a a
bcd
ab
ef
cd
ghi
b
c
d
B
b
a
c
d
a a
bcd
ab
ef
cd
ghi
b
c
d
Connector Connect to
1 MIC Microphone
2 REAR LINE
OUT R
Rear right
speaker
3 REAR LINE
OUT L
Rear left speaker
4 SUB OUT Subwoofer
5 ANTENNA Antenna
2Cut off the bigger end of the supplied
standard connector.
3Check the car’s wiring carefully and
connect them to the supplied standard
connector.
A1 A2 A3 A4 A5 A6 A7 A8
B1 B2 B3 B4 B5 B6 B7 B8
A
A
B
a b c d e
A1 A2 A3 A4 A5 A6 A7 A8
B1 B2 B3 B4 B5 B6 B7 B8
A
A
B
a b c d e
Mount in the dashboard
1If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
If you disconnect the car battery in
a car that has an on-board drive or
navigation computer, the computer
may lose its memory.
If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
wires do not touch each other.
2Remove the mounting sleeve with the
supplied disassembly tools.
3Ensure that car dashboard opening is
within these measurements:
•
•
4Connect the supplied standard connector
to the unit.
Attach the front panel
1Insert the right side of the panel in the
chassis until it is correctly engaged.
2Press the left side of the panel and point
the left hole at the left pillar.
3Release the panel to engage the left side.
4Attach the trim plate.
EN
English
EN

14
15
6Place the supplied rubber cushion over the
end of the mounting bolt.
7Slide the unit into the dashboard until you
hear a click sound.
8Reconnect the negative terminal of the car
battery.
4Install the sleeve into the dashboard and
bend the tabs outward to x the sleeve.
Note
Skip this step if the unit is not xed by sleeve but
supplied screws.
•
5Remove the two screws on the top of the
unit.
183 mm
52mm
4.75-5.56 mm
183 mm
52mm
4.75-5.56 mm
Set clock
1Press MENU/DISP for 3 seconds.
2Press or repeatedly until the currently
time is displayed.
3Turn clockwise to set hour.
4Turn anti-clockwise to set minute.
5Press to conrm.
View clock
1Press MENU/DISP repeatedly until the
clock is displayed.
Install remote control battery
Caution
Risk of explosion! Keep batteries away from heat,
sunshine or re. Never discard batteries in re.
Risk of decreased battery life! Never mix different
brands or types of batteries.
Risk of product damage! When the remote control is
not used for long periods, remove the batteries.
Perchlorate Material - special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate.
•
•
•
•
Forrst-timeuse:
1Remove the protective tab to activate the
remote control battery.
To replace the remote control battery:
1Open the battery compartment.
2Insert 1 CR2025 batteries with correct
polarity (+/-) as indicated.
Close the battery compartment.
Turn on
1Press to turn on the unit.
To turn off the unit, press for 3
seconds.
•
EN
English
EN

16
17
Store radio stations in
memory
You can store up to 6 stations in each band.
Store staions automatically
1Press SEARCH for 3 seconds.
The six strongest stations of the
selected band are saved in preset
channels 1-6 automatically.
Store staions manually
1Tune to a station that you want to store.
(see ‘Tune to a radio station’ on page 16)
2Press one of the numbered buttons 1to 6
for 3 seconds.
The station is saved in the selected
channel.
Tune to a preset station
1Press or to select band.
2Press the number button 1to 6to select
the preset station.
»
»
4 Listen to radio
Tune to a radio station
1Press SOURCE repeatedly to select Tuner.
2Press or to select band: [FM1], [FM2],
[FM3], [AM1], or [AM2] .
3Press or to tune to a radio station
manually.
The radio station is broadcast.
To search for a radio station
automatically, press or for 3
seconds.
Select tuner sensitivity
You can adjust the tuner sensitivity if you want
to receive more radio stations or only stations
with strong signal.
1Press MENU/DISP for over 2 seconds.
2Press or repeatedly until [LOCAL] or
[DX] is displayed.
3Rotate to select a setting:
[LOCAL] (local): Only stations with
strong signal can be broadcast.
[DX] (distance): Stations with strong
and weak signals can be broadcast.
4Press to conrm the selection.
Select stereo/mono broadcasting
For stations with weak signals: to improve the
reception, change to monoaural sound.
1Press MENU/DISP for 3 seconds.
2Press or repeatedly until [STEREO]
or [MONO] is displayed.
3Turn to select a setting:
[STEREO]: stereo broadcast.
[MONO]: mono broadcast.
4Press to conrm the selection.
»
»
•
•
•
•
2Speak a name stored in contact list stored
in the phone.
The unit repeats the number and calls
out.
[NO MATCH] is displayed if the unit
does not recognize a number.
Make a call
1Press .
2Press 0-9 to enter phone number.
Press / to change a number.
Press to reset entered numbers.
3Press to dial.
Call waiting
If there is another incoming call during call,
[CALL WAITING] ashes on the display panel.
1Press to terminate the present call.
The other call is automatically
answered.
The rst call is terminated.
Call transfer
You can transfer voice from loudspeaker to
mobile phones during call.
1Press .
[TRANSFER] is displayed.
Terminate call
aPress to terminate call.
»
»
•
•
»
»
»
5 Use bluetooth
devices
With this car audio system, you can listen
to audio les from a player or make a call
if bluetooth connection is available on your
phone or player.
Pairing bluetooth devices
You can pair your bluetooth device with the
unit as follows:
1Turn on bluetooth function on the device.
2Setup bluetooth fuction on your device.
3Select “CEM250” in the pairing list.
4Enter default password “0000”.
“[PAIR OK]” is displayed on the panel
if pairing succeeds.
Otherwise, “[PAIR ERR]” is displayed.
“[CONNECT]” is displayed when
connection is established.
Playaudioles
You can listen to audio from a bluetooth device
and control playback with the unit.
1Press SOURCE repeatedly to select [BT
MUSIC].
To play, press 1, .
To pause, press 1, again.
Voice dialing
You can dial a number by voice if your mobile
phone supports voice dialing.
1Press for 3 seconds.
[VOIC DIAL] is displayed.
»
»
»
•
•
»
EN
English
EN