Philips Dynalite DDRC810DT-GL User manual

DDRC810DT-GL
RJ12
215 mm (8.46 in)
93 mm (3.66 in)
103 mm (4.05 i
n)
64 mm (2.51 in)
1
45 mm
(2 in)
45 mm
(2 in)
Relay Controller
www.lighting.philips.com/dynalite
Installation Instructions
Instructions d’installation
Installationsanweisungen
Instrucciones de instalación
Istruzioni per l’installazione
Installatie-instructies
インストー ル 手 順
安装指示
50° C (122° F)
-5° C (23° F)
≤
90%
IEC Pollution Degree II
Devices must be installed in an
approved enclosure by a qualied
electrician in accordance with all
national and local electrical and
construction codes and regulations.
Les appareils doivent être installés dans un lieu jugé
apte, par un électricien qualié et conformément
aux règles et normes locales et nationales en
matière d’électricité et de construction.
Die Geräte müssen von einem geprüften Elektriker
entsprechend allen nationalen und lokalen Elektro
– und Bauvorschriften in einem zugelassenen
Gehäuse installiert werden.
Los dispositivos se deben instalar en un recinto
aprobado por un electricista cualicado de
acuerdo a todos los reglamentos eléctricos y de
construcción locales y nacionales pertinentes
I dispositivi devono essere installati da un
elettricista qualicato in un luogo approvato, in
conformità a tutti gli standard e le norme nazionali
e locali vigenti in materia di impianti elettrici e
costruzioni edilizie.
Apparaten moeten door een erkende elektricien
worden geïnstalleerd in een goedgekeurde
behuizing in overeenstemming met alle nationale
en lokale elektriciteits – en bouwvoorschriften
en wetgeving.
デバイスを取り付ける際は、資格のある電気技師に依頼
し、電気と建設に関する国および地域のすべての法令に
従って、認可されている筐体内に取り付けてください。
根据国家/地区及当地的电气与建筑规范和法规，该设
备必须由有资质的电工安装在经批准的外罩内。

C
L N
NO NC CNO NC
CH1 CH2
M
CNO NC CNO NC
CH1 CH2
PLC
M
COM
CH1-CH2, CH3-CH4, CH5-CH6, CH7-CH8 ≤ 9.8 FLA (1/
2
HP), 120 V
CH1-CH2, CH3-CH4, CH5-CH6, CH7-CH8 ≤ 8 FLA (1 HP), 240 V
DDRC810DT-GL ≤ 40 A
Output Ratings/Group
3 A 3 B
100-240 V
0.25 A
+12 V
D +
D -
GND
SHLD
AUX
N L
COM
NO
NC
CH1
COM
NO
NC
CH2
COM
NO
NC
CH3
µP
COM
NO
NC
CH4
COM
NO
NC
CH5
COM
NO
NC
CH6
COM
NO
NC
CH7
COM
NO
NC
CH8
DyNet
SELV/Class 2
RS-485
RJ12
Dry Contact 3
Common
Dry Contact 4
Common
Dry Contact 1
Dry Contact 2
Dry Contact 6
Dry Contact 5
Common Common
Dry Contact 7
Dry Contact 8
12 V 120 mA
Dry Contact Inputs
4
IEC Overvoltage Category III
CN NOLNC CNO NC CNO NC CNO NC CNO NC CNO NC CNO NC CNO
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
NC
Output Ratings/Channel (CH)
General Use
Load Type
10 A, 240 V
5 A, 24 V
5 A, 240 V
1 A, 120 V
0.5 A, 240 V
9.8 FLA (1/
2
HP), 120 V
8 FLA (1 HP), 240 V
100 A
Incandescent
TV-5, 120 V
5 A, 240 V
5 A, 24 V
CH1-CH8 N/CCH1-CH8 N/O
TV Rating
Inrush Current
Electronic Ballast
Motor
M
Output Ratings/Group
CH-CH ≤ 400 V
DDRC810DT-GL ≤ 40 A
≤5 mm2
10+ AWG
0.62 Nm
5.5 Lb-in
2

DyNet
RS-485
RJ12 RJ12
0.56 Nm
5 Lb-in
≤2.5 mm2
12+ AWG
SHLD D+ GND D-
+12 V AUX
SHLD GND D+ D- +12V AUX
DyNet RS-485
GND AUX
< 20 m
≤ 2 A
6 A 6 B
DyNet RS-485
7
1C32 4C5C6 7 C8
1 C
< 20 m ≤1.5 mm2
16+ AWG
0.33 Nm
3.0 Lb-in
5

Philips Dynalite
www.lighting.philips.com/dynalite
© 2017 Philips Lighting. All rights reserved.
Installation of a home and building automation and control system shall comply with HD 60364-4-41. The temperature limits and current-carrying capacities for
the communication wires specied in HD 384.5.523 shall not be exceeded.
8