Philips dynalite DMRC210-RJ-DA User manual

…………………………………………………....…………………………………………………………
DMRC210-RJ-DA
EcoSet Relay Controller
Installation Instructions
…………………………………………………....……………………………………………………
……
Connect Data Cable in a ‘Daisy Chain’
Serial Cable Termination
RJ12 connectors using flat cable recommended.
Double-adaptor (Y-splitter) is usable for spurs.
Electrical diagram
RJ12
DyNet
RS485
RJ12
µP
DIPswitch
Supply:
230V
1 Phase
20A
LIN
NCH1
out CH2
out
N
isolation barrier
(double-insulated)
Installation Overview
WARNING
Before installation or servicing,
disconnect power at circuit breakers or
remove fuses to avoid electrical shock
or damage to the unit. It is
recommended that an electrician
perform this installation.
To reduce the risk of fire or electric shock , do not expose this
device to rain or moisture.
Do not energise unless the front cover is in place. Network (DyNet)
wiring is SELV and must be double –insulated from mains in
accordance with the local wiring rules. Installation, programming
and maintenance must be carried out by qualified personnel.
No more than 60 DMRC210 units may be safely connected to a
single Dynet network without additional grounding precautions.

…………………………………………………....…………………………………………………………........
..
Mounting dimensions
Product specifications
…………………………………………………....…………………………………………………………
…………………………………………………....…………………………………………………………
Supply
100-240V 50/60Hz Single Phase at 20A
Dynet DC Supply:
150mA@12VDC
Switched output
2 x switched output at 10A (inductive)
Switching Device
Relay, Tungsten Carbide pilot contact,
12A inductive, 120A surge
Control Inputs 1 x RS485 DyNet/2 X RJ12 connectors
File button configurations R7
Supply Terminals
Line, Neutral
1 x 4mm2 max conductor size
Output Terminals
CH1, CH2, Neutral
1 x 4mm2 max conductor size
Compliance CE, C-Tick
Operating Environment
0º to 50ºC ambient temp
0% to 90% RH non condensing
IP rating : 20 (all supplied lids closed)
Enclosure polycarbonate
Dimensions L 240mm x W 45mm x D 38mm
Weight Packed weight 0.19kg
Installation steps
1. Insert a screwdriver into the keyslot , and open the end lids.
2. Unscrew and remove the cable retainers on both sides of the controller box
3. Insert RJ12 DyNet connectors into sockets.
4. Fasten the cable clamp on the cable of the DyNet cable(s).
5. Remove at least 10 mm of insulation and fasten load power cables into pressure-pad screw terminals , CH1, CH2
6. Remove at least 10mm of insulation and fasten L and N mains cables into pressure pad screw terminals.
7. Fasten the cable clamp over the power leads.
8. Close end lids on both sides after terminations are complete.
9. Fix the housing to a fixed flat surface using two screw flanges and 5 mm screws. Allow no contact with other devices.
10. For indoor use only. Observe IP rating requirements in installation.
11. DIPswitches are set according to Truth Tables; see Channel 1 and Channel 2 tables.
…………………………………………………....…………………………………………………………
Recommended Cable
200m Unterminated Roll: DYNET-SFLAT6-CABLE
10m Patchlead: DYNET-SFLAT6-CABLE-10M
5m Patchlead: DYNET-SFLAT6-CABLE-5M
3m Patchlead: DYNET-SFLAT6-CABLE-3M
Reference:
Philips Dynalite EcoSet System Technical Guide
Channel 1
Channel 2
Area
Sw1
Sw2
Sw3
Sw4
Sw5
Area
Sw6
Sw7
Sw8
Sw9
Sw10
1.
ON
0
0
0
0
1.
ON
0
0
0
0
2.
0
ON
0
0
0
2.
0
ON
0
0
0
3.
ON
ON
0
0
0
3.
ON
ON
0
0
0
4.
0
0
ON
0
0
4.
0
0
ON
0
0
5.
ON
0
ON
0
0
5.
ON
0
ON
0
0
6.
0
ON
ON
0
0
6.
0
ON
ON
0
0
7.
ON
ON
ON
0
0
7.
ON
ON
ON
0
0
8.
0
0
0
ON
0
8.
0
0
0
ON
0
9.
ON
0
0
ON
0
9.
ON
0
0
ON
0
10.
0
ON
0
ON
0
10.
0
ON
0
ON
0
11.
ON
ON
0
ON
0
11.
ON
ON
0
ON
0
12.
0
0
ON
ON
0
12.
0
0
ON
ON
0
13.
ON
0
ON
ON
0
13.
ON
0
ON
ON
0
14.
0
ON
ON
ON
0
14.
0
ON
ON
ON
0
15.
ON
ON
ON
ON
0
15.
ON
ON
ON
ON
0
16.
0
0
0
0
ON
16.
0
0
0
0
ON
17.
ON
0
0
0
ON
17.
ON
0
0
0
ON
18.
0
ON
0
0
ON
18.
0
ON
0
0
ON
19.
ON
ON
0
0
ON
19.
ON
ON
0
0
ON
20.
0
0
ON
0
ON
20.
0
0
ON
0
ON
21.
ON
0
ON
0
ON
21.
ON
0
ON
0
ON
22.
0
ON
ON
0
ON
22.
0
ON
ON
0
ON
23.
ON
ON
ON
0
ON
23.
ON
ON
ON
0
ON
24.
0
0
0
ON
ON
24.
0
0
0
ON
ON
25.
ON
0
0
ON
ON
25.
ON
0
0
ON
ON
26.
0
ON
0
ON
ON
26.
0
ON
0
ON
ON
27.
ON
ON
0
ON
ON
27.
ON
ON
0
ON
ON
28.
0
0
ON
ON
ON
28.
0
0
ON
ON
ON
29.
ON
0
ON
ON
ON
29.
ON
0
ON
ON
ON
30.
0
ON
ON
ON
ON
30.
0
ON
ON
ON
ON
31.
ON
ON
ON
ON
ON
31.
ON
ON
ON
ON
ON
Web: dynalite-online.com
E-Mail: info@ dynalite-online.com
Tel: [phone]
DMRC210-RJ-DA Installation Instructions Rev A Sept 2010
Specifications subject to change without notice. All rights reserved.
Dynalite, DyNet and associated logos are the registered trademarks
of Philips Dynalite. Not to be reproduced without permission.
Manufactured by WMGD Pty Ltd (ABN 33 097 246 921) Unit 6, 691
Gardeners Road, Mascot, NSW 2020, Australia