Philips DC220 User manual

1 Important Safety Important Safety Instructions a Read these instructions. b Keep these instructions. c Heed all warnings. d Follow all instructions. e Do not use this apparatus near water. f Clean only with dry cloth. g Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
h Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that produce heat.
i Protect the power cord from being walked on or pinched, par-
ticularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
j Only use attachments/accessories specified by the manufacturer. k Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer or sold with the apparatus.When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
l Unplug this apparatus during lightning storms or when unused
for long periods of time.
m Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
n Battery usage CAUTION – To prevent battery leakage which
may result in bodily injury, property damage, or damage to the unit:
Install all batteries correctly, + and - as marked on the unit.
•
Do not mix batteries (old and new or carbon and alkaline,
•
etc.). Remove batteries when the unit is not used for a long time.
•
The batteries shall not be exposed to excessive heat such as
•
sunshine, fire or the like.
o Apparatus shall not be exposed to dripping or splashing. p Do not place any sources of danger on the apparatus (e.g. liquid
filled objects, lighted candles).
q This product may contain lead and mercury. Disposal of these
materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org.
r Where the MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain readily operable.
Warning
Never remove the casing of this apparatus.• Never lubricate any part of this apparatus.• Never place this apparatus on other electrical equipment.• Keep this apparatus away from direct sunlight, naked flames or heat.• Ensure that you always have easy access to the power cord, plug or• adaptor to disconnect the apparatus from the power.
Copyright in the U.K. Recording and playback of material may require consent. See Copyright Act 1956 and The Performers’s Protection Acts 1958 to 1972. Notice Any changes or modifications made to this device that are not expressly
approved by Philips Consumer Lifestyle may void the user’s authority to operate the equipment.
This product complies with the radio interference requirements of the European Community. This product complies with the requirements of the following directives and guidelines: 2004/108/EC + 2006/95/EC Recycling Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. When you see the crossed-out wheel bin symbol attached to a product, it means the product is covered by the European Directive 2002/96/EC: Never dispose of your product with other household waste. Please inform yourself about the local rules on the separate collection of elec- trical and electronic products.The correct disposal of your old product helps prevent potentially negative consequences on the environment and human health. Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed of with normal household waste. Please inform yourself about the local rules on separate collection of batteries.The correct disposal of batteries helps prevent potentially negative consequences on the environment and human health. Environmental information All unnecessary packaging has been omitted.We have tried to make the packaging easy to separate into three materials: cardboard (box), poly- styrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regula- tions regarding the disposal of packaging materials, exhausted batteries and old equipment.
Note
The type plate is located on the bottom of the apparatus.•
Register your product and get support at www.philips.com/welcome
EN User manual
DC220
© 2010 Koninklijke Philips Electronics N.V. All rights reserved. DC220_05_UM_V1.1
2 Your Clock Radio for iPhone/iPod Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. Introduction With this unit, you can enjoy audio from the iPod, iPhone, other audio devices, or the radio. The radio, iPod, or iPhone can be set as the alarm timer.You can set two alarm timers to go off at different time. What’s in the box Check and identify the contents of your package:
Main unit
•
1 x AC power adaptor• 1 x MP3 LINK cable• User manual• Quick start guide•
Overview of the main unit Top View a POWER
Turn on the unit or switch to standby mode.
•
Deactivate the sleep timer.• Stop alarm.•
b DATE • AUTOTUNE/TIME SET
Set the date and clock.
•
Search and program radio stations automatically.•
c AL 1/AL 2
Set the alarm timer.
•
Turn off the alarm tone.• View alarm settings.•
REPEAT ALARM
BRIGHTNESS CONTROL
E
MULOV
TUNING
TUNING
SOURCE SLEEP AL2
AL1
BBD
DOCK for
a b c d e
l jk i gh f
d /
Skip to the previous/next audio file.
•
Search within an audio file.• Select a preset radio station.• Adjust time.•
e TUNING +/-
Tune to a radio station.
•
Adjust time.•
f VOL +/-
Adjust volume.
•
g
Start or pause iPod/iPhone play.
•
h REPEAT ALARM/BRIGHTNESS CONTROL
Repeat the alarm.
•
Adjust the display brightness.•
i iPod/iPhone dock
Load an iPod/iPhone.
•
j DBB
Turn on or off dynamic bass enhancement.
•
k SLEEP
Set the sleep timer.
•
l SOURCE
Select a source: iPod/iPhone, FM tuner or AUX.
•
Back View OPEN
MP3 LINK FM AERIAL
9V DC IN
n o m
p
m Backup battery compartment
Insert 2 pieces of AAA/R03/UM4, 1.5V batteries.
•
n FM AERIAL
Improve FM reception.
•
o MP3-LINK
Jack for an external audio device.
•
p DC IN
Power supply socket.
•
3 Get started
Caution
Use of controls or adjustments or performance of procedures• other than herein may result in hazardous radiation exposure or other unsafe operation.
Always follow the instructions in this chapter in sequence. If you contact Philips, you will be asked for the model and serial number of this apparatus.The model number and serial number are on the bot- tom of the apparatus. Write the numbers here: Model No. __________________________ Serial No. ___________________________
Connect power
Caution
Risk of product damage! Ensure that the power voltage• corresponds to the voltage printed on the back or underside of the apparatus. Ris
• k of electric shock! When you unplug the AC adaptor, always pull
the plug from the socket. Never pull the cord. Befor
• e connecting the AC adaptor, ensure you have completed all
other connections.
1Connect one end of the AC adaptor to the DC IN socket on the
main unit.
2 Connect the other end of the AC adaptor to the wall outlet.
Note
The voltage and power rating information is located on the bottom• of the unit.
Set time and date 1 Dock the iPod/iPhone on the unit. 2Open the iPod/iPhone.
Time and date information on the iPod/iPhone transfers to the
»
unit automatically.
To set time and date manually: 1In standby mode, press and hold DATE • AUTO TUNE/TIME SET
for 2 seconds.
[24 HR] begins to blink.
»
2 PressTUNING +/- or / to select 12/24 hour format.
3 Press DATE • AUTO TUNE/TIME SET to confirm.
The hour digits begin to blink.
»
4 Press TUNING +/- or / to set the hour.
5 Press DATE • AUTO TUNE/TIME SETto confirm.
The minute digits begin to blink.
»
6 Repeat steps 4-5 to set the minute, year, month, and day.
Turn on 1 Press POWER.
The unit switches to the last selected source.
»
Switch to standby 1 Press POWER again to switch the unit to standby mode.
The time and date (if set) appear on the display panel.
»

4 Play Play from iPod/iPhone You can enjoy audio from iPod/iPhone through this unit. Compatible iPod/iPhone Apple iPod and iPhone models with a 30-pin dock connector:
iPod classic, iPod touch, iPod nano, iPod 5th generation (video), iPod
•
with color display, iPod mini. iPhone, iPhone 3G, iPhone 3GS.
• Listen to the iPod/iPhone 1Place the iPod/iPhone into the dock. 2Press SOURCE repeatedly to select iPod/iPhone source.
The connected iPod/iPhone plays automatically.
»
To pause/resume play, press
•.
To skip to a track, press
•/ .
To search during play, press and hold
•/, then release to
resume normal play.
Charge the iPod/iPhone When the unit is connected to power, the docked iPod/iPhone begins to charge.
Tip
For certain iPod models, it may take up to a minute before the• charging indication appears.
Play from an external device You can also listen to an external audio device through this unit. 1Press SOURCE repeatedly to select AUX source. 2Connect the supplied MP3 link cable to:
the
•MP3 LINK jack (3.5mm) on the back of the unit.
the headphone jack on an external device.
•
3Start to play the device (see the device user manual). 5 Listen to radio
Note
Only FM radio reception is available on this unit.•
Tune to a radio station
Tip
Position the antenna as far as possible from TV,VCR or other radia-• tion source.
Note
For optimal reception, fully extend and adjust the position of the• antenna.
1Press SOURCE to select FM. 2Press and hold TUNING +/- for more than 2 seconds.
[SRCH]
»(search) displays.
The radio tunes to a station with strong reception
»
automatically.
3Repeat step 2 to tune to more stations.
To tune to a weak station, press
•TUNING +/- repeatedly until
you find optimal reception.
Program radio stations automatically You can program a maximum of 20 preset radio stations. 1In the tuner mode, press and hold DATE • AUTO TUNE/TIME SET
for more than 2 seconds to activate automatic program mode.
[AUTO] (auto) idisplays.
»
All available stations are programmed in the order of
»
waveband reception strength. The first programmed radio station is broadcast automatically.
»
Program radio stations manually You can program a maximum of 20 preset radio stations. 1Tune to a radio station. 2Press DATE • AUTO TUNE/TIME SET to activate the program
mode.
PR01 begins to blink.
»
3Press DATE • AUTO TUNE/TIME SET to confirm. 4Repeat the above steps to program other stations.
Tip
To overwrite a programmed station, store another station in its• place.
Select a preset radio station 1Press / to select a preset program number. 6 Other features Set the alarm timer You can set two alarms which go off at different time. 1Ensure that you have set the clock correctly. 2Press and hold AL 1 or AL 2 for 2 seconds.
[AL 1] or [AL 2] begin to blink.
»
3Press SOURCE repeatedly to select an alarm sound source: iPod/
iPhone, iPod/iPhone playlist, FM tuner, or buzzer.
4Press AL 1 or AL 2.
Hour digits begin to blink.
»
5Press TUNING +/- or / repeatedly to set the hour.
6Press AL 1 or AL 2 to confirm.
Minute digits begin to blink.
»
7Repeat steps 5-6 to set the minute. 8Repeat steps 5-6 to select whether to ring alarm the whole week,
on weekdays, or at weekend.
9Repeat steps 5-6 to set the alarm volume.
Tip
If you want to wake up to specific music track(s) on iPhone/iPod,• after set iPhone/iPod playlist as the wake up source on the unit, you need to create a playlist called ‘PHILIPS’ via iTunes and copy the track(s) to this new ‘PHILIPS’ playlist. If no playlist is created or there is no song in the playlist, the unit will
•
play the music track according to the last music playback preference on iPhone/iPod.
Activate and deactivate the alarm timer 1Press AL 1 or AL 2 repeatedly to activate or deactivate the timer.
If the timer is activated, [
»AL 1] or [ AL2] is displayed.
If the timer is deactivated,
»before [AL1] or [AL2] disappears.
Gentle wake Gentle wake function peacefully wakes you with gently ascending alarm volume.
If selected the alarm source iPhone/iPod, iPhone/iPod playlist or FM,
•
alarm volume will gentle increase. If selected the alarm source Buzzer, the alarm will increases beep
•
tone frequency within seconds.
Repeat alarm 1When the alarm rings, press BRIGHTNESS/REP ALM.
The alarm repeats ringing minutes later.
»
Tip
You can press•/ to adjust the interval to repeat alarm.
Stop alarm ring 1When the alarm rings, press the corresponding AL 1 or AL 2.
The alarm stops but the alarm settings remain.
»
View the alarm settings 1Press AL 1 or AL 2. Backup Battery Mode Under normal use, the unit should be powered through the AC adapter. If the AC adapter is disconnected, the unit will automatically switch to Backup Battery mode. Under Backup Battery mode:
The unit displays the same as under the Standby mode, with
•
backlight off. Only the functions below are available:
•
Clock
•
Alarm
•
Note
Alarm source is defaulted to ‘Buzzer’ under Backup Batter y mode.•
When AC Power is plugged back, the unit will exit Backup Battery mode and go to Standby mode.
Note
•Under Backup Battery mode, the unit can work over 3 months.
When the battery power is low, the display panel will indicate
•
“bAtt Lo” until the batteries are empty and the unit will switch off automatically. In this case, please replace the batteries in the backup battery compartment with 2 pieces of new 1.5V, AAA/R03/UM4 batteries.
Install backup batteries
Caution
Risk of explosion! Keep batteries away from heat, sunshine or fire.• Never discard batteries in fire. Risk of product damage! When the apparatus is not used for long
•
periods, remove the battery.
1Open the battery compartment on the back of the unit. 2Insert 2 x 1.5V R03/UM-4/AAA batteries with correct polarity. 3Close the battery compartment.
Note
•Batteries contain chemical substances, so they should be disposed
of properly.
Set the sleep timer This unit can switch to standby automatically after a set period of time. 1Press SLEEP repeatedly to select a set period of time (in minutes).
The sleep timer is activated
»
The display shows
»
The volume starts to decrease gradually from the last 5
»
minutes of sleep timer The unit switches to standby when reaches the set time.
»
To deactivate sleep timer 1Press SLEEP repeatedly until [OFF] displays.
»disappears on the display.
Adjust display brightness 1Press BRIGHTNESS/REP ALM repeatedly to select different levels
of display brightness.
7 Adjust sound Adjust volume level 1During play, press VOL +/- to increase/decrease the volume level. Enhance bass 1During play, press DBB to turn on or off dynamic bass enhance-
ment.
If DBB is activated, [DBB] is displayed.
»
8 Product information
Note
Product information is subject to change without prior notice.•
Specifications Amplifier
Rated Output Power 2 x 2.5 W RMS Frequency Response 125 Hz - 16 kHz, ±3 dB Signal to Noise Ratio >55 dB MP3 link 500 mV RMS 10 kohm
Tuner FM
Tuning Range 87.5 - 108 MHz Tuning grid 50 KHz Sensitivity - Mono, 26dB S/N Ratio - Stereo, 46dB S/N Ratio
<22 dBu <45 dBu
Search Selectivity <36 dBu Total Harmonic Distortion <3% Signal to Noise Ratio >45 dB
General information
AC power (power adaptor) AS190-090-Al180;
Input: 100-240 V~, 50/60Hz, 0,7 A; Class II; Output: 9.0V 1.8A
Operation Power Consumption 10 W Standby Power Consumption <1 W Dimensions - Main Unit (W x H x D) 216.9 x105 x139.4 mm Weight - Main Unit 0.75 kg
9 Troubleshooting
Warning
Never remove the casing of this apparatus.•
To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this apparatus, check the follow- ing points before requesting service. If the problem remains unsolved, go to the Philips web site (www.philips.com/welcome).When you contact Philips, ensure that the apparatus is nearby and the model number and serial number are available. No power
Ensure that the AC power plug of the unit is connected properly.• Ensure that there is power at the AC outlet.•
No sound
Adjust the volume.•
No response from the unit
Disconnect and reconnect the AC power plug, then turn on the• unit again.
Poor radio reception
Increase the distance between the unit and yourTV or VCR.• Fully extend the FM antenna.•
Timer does not work
Set the clock correctly.• Switch on the timer.•
Clock/timer setting erased
Power has been interrupted or the power plug has been discon-• nected. Reset the clock/timer.•
Note