Philips HR 2831/B User manual

ServiceManual
Philips Domestic Appliances and Personal Care
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
Service Manual 4322 277 00103 is herewith cancelled.
Food processor
HR 2831/B
HR 2833/B
Product meets the requirements regarding
interference suppression on radio and TV.
After the product has been repaired, it should
function properly and has to meet the safety
requirements as laid down officially estab-
lished at this moment.
Cucina
PRODUCT INFORMATION
Motor : Universal, radio/TV interference
suppressed power
Consumption : 350 Watt
Voltage 220-240V, 120V, 50-60Hz
Cordset : 1.2m, double insulated
Speed setting HR 2831 : 1 speed + pulse
HR 2833 : vario speed + pulse (500-1800 rpm)
Bowl capacity : 2.2 L dry ingredients
0.8 L liquids
Kneading capacity : 250 g of flour with metal knife
: 350 g of flour with metal kneader
Dimensions product : 270 x 200 x 250 mm (l x w x h)
SERVICE INFORMATION
Use grease 4822 390 20004 to lubricate the parts of the gearbox.
4322 277 00351
00/08
Note:
Support the rotorshaft to prevent forces on the motor bearings,
during the assembly of the pinion on the rotorshaft.
3,50 ± 0,15
44A

SERVICE INFORMATION
HR 2831 HR 2833
1 4203 065 62230 Pulse knob assy x x
2 4203 065 62240 Upper housing assy x -
4203 065 62250 Upper housing assy - x
3 4822 466 11658 Motor buffer x x
4 4822 361 11005 Drive unit 220-240V x x
4203 065 61580 Drive unit 110-127V x x
4A 4203 065 61800 Gearbox + pinion x x
5 4822 466 62531 Drive unit buffer x x
6 4822 277 11718 Safety swit h x x
HR 2831 HR 2833
7 4822 441 12041 Lower housing x x
8 4822 528 11164 Drive oupling x x
9 4822 690 10114 Food pusher x x
10 4822 442 00892 Bowl over x x
11 4822 321 10364 Cord x x
12 4822 214 12419 Speed ontrol unit - x
13 4203 065 62260 Bowl assy x x
14 4822 690 40212 Spatula x x
- 4822 290 40369 Cord lip x x
2
1
3
44A
5
7
6
8
9
10
11
12
13
14
DAP1009

HR 2831 HR 2833
15 4822 690 10115 Balloon beater - x
16 4822 522 10615 Gear box - x
16A 4203 065 62270 Kneading tube - x
17 4822 690 10116 Kneading hook - x
18 4203 065 62280 Si kle knife x x
19 4822 528 11108 A essory holder x x
20 4203 065 61530 Sli ing insert fi ne x x
HR 2831 HR 2833
21 4203 065 61540 Sli ing insert medium x x
22 4203 065 61570 Granulating insert x x
23 4203 065 61550 Shredding insert fi ne x x
24 4203 065 61560 Shredding insert medium x x
25 4203 065 62310 Shredding insert oarse x x
26 4203 065 61520 Insert arier x x
27 4822 442 01104 Bowl over (opt.) x x
HR 2833 only
DAP1008
23
24
25
26
22
21
20
27
19
18
15
16
16A
17

MAX
SERVICE INSTRUCTION FOR PRINT-ASSY HR 2831/33
HR 2833
–turn the poti-gear to the MAX. left position.
mount the print-plate in the housing.
–
turn the speed-knob to the most right position for
one time;
the poti-gear is now right position.
–
HR 2831
turn the poti-gear to the MAX. left position.
remove the poti-gear.
mount the print-plate in the housing.
–
–
–
turn the speed-knob to pos. 2
put a screw driver to trim the
speed to 1250 rpm.
–
poti-gear
1. put the speed knob to the most left position.
SERVICE INSTRUCTION FOR REMOVING THE PULSE KNOB
2. take a small screw driver and press it between
speed knob and pulse knob.
3. turn the screw driver to pull the knob a little bit out
of the power unit (a), set the screw driver deeper
into the created hole (b) and lift it (c).
4. pull the pulse knob out of the speed knob.
ac
b