Philips 373720 User manual

311/32''
◗Ordering Information
Ordering Code CDM35/TC/830
ANSI Designation M130/E
Product Number 373720
DescriptionMasterColor Ceramic Metal Halide
Package Quantity 12
◗Physical Characteristics
Bulb Size T-4
Bulb Finish Clear
Base G-8.5 Bi-Pin
Max. Overall Length (MOL) 3.35'' (85mm)
Light Center Length (LCL) 2.0'' (52mm)
Arc Length 0.2'' (5mm)
Arc Tube Material Polycrystalline Alumina
Max. Permissible Bulb Temp. 500ºC (932ºF)
Max. Permissible Pinch Temp. 300ºC (572ºF)
Max. Arc Tube to Pinch Eccentricity 3º
◗Operating Characteristics (Photometric)
Rated Initial Lumens13300
Mean Lumens,Approx.22640
Rated Average Life, Hours 9000
Correlated Color Temp. (CCT)23000K
CIE Chromaticity Approx.2x-.432, y-.394
Color Rendering Index (CRI) 81
Efficacy (lpw) 85
◗Operating Position
Universal-Enclosed Luminaires Only
Note: Use on thermally protected electronic ballast only.
MasterColor® Spectral Power Distribution—3KTypes
RELATIVE ENERGY
400 450 500 550 600 650 700
WAVELENGTH (Nanometers)
350
300
250
200
150
100
50
0
MasterColor®Ceramic Metal Halide
39 Watt TC 3K Lamp
with FadeBlock™

Warnings, Cautions and Operating Instructions
“WARNING: These lamps can cause serious skin burn and eye inflammation from
short wave ultraviolet radiation if outer envelope of the lamp is broken or punctured.
Do not use where people will remain for more than a few minutes unless adequate
shielding or other safety precautions are used. Certain lamps that will automatically
extinguish when the outer envelope is broken or punctured are commercially
available.” This lamp complies with FDA radiation performance standard 21 CFR
subchapter J. (USA:21CFR 1040.30 Canada:SOR/DORS/80-381)
If the outer bulb is broken or punctured, turn off at once and replace
the lamp to avoid possible injury from hazardous short wave ultraviolet
radiation. Do not scratch the outer bulb or subject it to pressure as this
could cause the outer bulb to crack or shatter. A partial vacuum in the
outer bulb may cause glass to fly if the envelope is struck.
WARNING: The arc-tube of metal halide lamps are designed to operate under high
pressure and at temperatures up to 1000º C and can unexpectedly rupture due to
internal or external factors such as a ballast failure or misapplication. If the arc-tube
ruptures for any reason, the outer bulb may break and pieces of extremely hot glass
might be discharged into the surrounding environment. If such a rupture were to
happen, THERE IS A RISK OF PERSONAL INJURY, PROPERTY DAMAGE,
BURNS AND FIRE.
Certain lamps that will retain all the glass particles should inner arc-tube
rupture occur are commercially available from Philips Lighting Company.
RELAMP FIXTURES AT OR BEFORE THE END OF RATED LIFE.
Allowing lamps to operate until they fail is not advised and may increase
the possibility of inner arc tube rupture.
This lamp contains an arc tube with a filling gas containing Kr-85 and is
distributed by Philips Lighting Company, a division of Philips Electronics
North America Corporation, Somerset, New Jersey, 08875.
CAUTION: TO REDUCE THE RISK OF PERSONAL INJURY, PROPERTY
DAMAGE, BURNS AND FIRE RESULTING FROM AN ARC-TUBE RUPTURE THE
FOLLOWING LAMP OPERATING INSTRUCTIONS MUST BE FOLLOWED:
LAMP OPERATING INSTRUCTIONS:
1. RELAMP FIXTURES AT OR BEFORE THE END OF RATED LIFE. Allowing lamps
to operate until they fail is not advised and may increase the possibility of inner
arc tube rupture.
2. Use only in fully enclosed fixtures capable of withstanding particles of glass
having temperatures up to 1000º C. Lens/diffuser material must be heat
resistant. Consult fixture manufacturer regarding the suitability of the fixture
for this lamp.
3. Do not operate a fixture with a missing or broken lens/diffuser.
4. Operate lamp only within specified limits of operating position.
5. Before lamp installation/replacement, shut power off and allow lamp and fixture
to cool to avoid electrical shock and potential burn hazards.
6. Use only auxiliary equipment meeting Philips and/or ANSI standards. Use within
voltage limits recommended by ballast manufacturer.
A. Operate lamp only within specified limits of operation.
B. For total supply load refer to ballast manufacturers electrical data.
C. Operate CDM-T (G12 base) and CDM-TC (G8.5 base) lamps only
on thermally protected ballasts.
D. Operate CDM-TC lamps (G8.5 base) only on electronic ballasts.
7. Periodically inspect the outer envelope. Replace any lamps that show scratches,
cracks or damage.
8. If a lamp bulb support is used, be sure to insulate the support electrically to avoid
possible decomposition of the bulb glass.
9. Protect lamp base, socket and wiring against moisture, corrosive atmospheres and
excessive heat.
10. Time should be allowed for lamps to stabilize in color when turned on for the
first time. This may require several hours of operation, with more than one start.
Lamp color is also subject to change under conditions of excess vibration or
shock, and color appearance may vary between individual lamps.
11. Lamps may require 4 to 8 minutes to re-light if there is a power interruption.
12.Take care in handling and disposing of lamps. If an arc tube is broken, avoid skin
contact with any of the contents or fragments.
Philips Lighting Company
200 Franklin Square Drive ■P. O. Box 6800
Somerset, NJ 08875-6800
1-800-555-0050
www.lighting.philips.com/nam
A Division of Philips Electronics North America Corporation
Updated 5/04 CDM 028
Philips Lighting
281 Hillmount Road
Markham, Ontario
Canada L6C 2S3
1-800-555-0050
www.lighting.philips.com/nam
A Division of Philips Electronics Ltd.
MasterColor®Ceramic Metal Halide 39 Watt TC 3K Lamp with FadeBlock™
Electrical Data (Subject to change without notice)
Lamp Watts (Nominal) . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Lamp Operating Voltage (rms) (Nominal) 2. . . . . . . . . . . 88
Initial Lamp Voltage Range (rms) 3. . . . . . . . . . . . . . . . . . . 80 -100
Lamp Operating Current (Amps) (rms) (Nominal). . . . . 0.53
Lamp Current Crest Factor (Maximum). . . . . . . . . . . . . . 1.8
Warm-up Time to 80% of Output . . . . . . . . . . . . . . . . . . 3 Minutes
Restrike Time for Hot Lamp . . . . . . . . . . . . . . . . . . . . . . . 4-8 Minutes
Ballast Type (Electronic Only) . . . . . . . . . . . . . . . . . . . . . . ANSI M130/E
Ballast Open Circuit Voltage (Minimum) . . . . . . . . . . . . . . 209 RMS Min.
Pulse Peak Volts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000 Minimum, 4000 Maximum
Pulse Width @ 90% Peak. . . . . . . . . . . . . . . . . . . . . . . . . . 2 Micro Second Minimum
Pulse Repetition Rate (Minimum)4. . . . . . . . . . . . . . . . . . 1 per Half Cycle
Minimum Operating Temperature . . . . . . . . . . . . . . . . . . . -30º C (-22°F)
1) Measured at 100 hours of life in vertical position.
2) Measured at rated lamp watts on a linear reactor. LPW does not include ballast losses.
3) Measured with the lamp operating at rated watts.
4) Option-Pulse Width @ 90% Peak, 1 micro second minimum with 2 pulses per half cycle.
Installation Information: MasterColor
®
Metal Halide TC lamps must be used in combination with appropriate fully electronic ballast only.
R