Philips InteGrade User manual

Quick installation guide
Philips InteGrade LED xture system
for indoor environments and
refrigerated cabinets (-30 to +30 °C / -22 to +86 °F)

2
Please take the time to read this installation guide before you install this Philips LED product and driver.
The guide contains important information regarding installation and operation.
Warranty
Warranty only applies when the appropriate Philips LED driver and Philips cabling (as described in this guide and leaets) are used.
Please visit our website www.philips.com/ledrefrigeration or contact your local sales ofce for more information.
Warnings
• The installation guide does not supersede local or (inter)national regulations for electrical installations.
• This Philips LED product and LED driver must be installed by a professional electrician in accordance with the applicable and
appropriate electrical codes and the instructions provided by Philips.
• Please note that the driver should be built into an enclosure (Tcase max. 70 °C / 158 °F).
• This Philips LED product is designed to be connected to a circuit from a class 2 power source (Philips Xitanium LED power driver)
with energy-limited supply.
• This is a 24 V DC product.
• Do not connect this LED product to mains voltages.
• To allow for variance in the installation, it is not recommended to load the power driver beyond 90% of its rated maximum power.
The energy consumption of the engine is a nominal value, with an estimated 20% deviation.
• Before installation, maintenance or cleaning, always rst switch off or disconnect the power and follow the appropriate safety
procedures.
• Before removing any lens covers or uorescent lamps, always rst switch off or disconnect the mains power to the lighting system.
• Take care not to damage the existing (heating) wiring if the LED product is installed in a freezer.
• Do not use tape to x this InteGrade LED product or LED prole in position; please use the appropriate mounting clips.
• Please note that the colors of the wires in existing designs, such as refrigeration systems or cabinets, may differ. The position of the
(original) ballast may also differ.
• Do not make sharp bends with electrical wires.
• Due to the variety of designs and brands in which the Philips LED products can be installed, you may need to use customized mounting
accessories to t the specic design you are using. If you require further support, please contact your local Philips sales organization.
• To prevent unwanted tripping caused by the inrush current of the LED driver, an MCB (mini circuit breaker) / fuse (slow blow) of
at least 6 A must be installed.
• Philips advises using a zero-crossing/switching solid-state relay to reduce the inrush current peak.
• This product is designed for damp and dry locations only.
Cleaning
• Use a damp cloth and a mild cleaning agent. Do not wipe the LED product with a dirty or very wet dishcloth or towel
because they may leave residue that can damage the LED product.
• Do not use abrasive cleaners, scouring pads, bleach or cleaners containing chlorine because they can scratch and damage
the LED product.
Important
NL
DE
FR
IT
ES
www.philips.com/ledrefrigeration
Installation instructions

3
InteGrade LED
fixture
Xitanium LED Power Driver
20 W 24Vdc - 929000654006
80 W 24 Vdc - 929000653906
InteGrade LED
cable angle
InteGrade LED
cable
InteGrade LED
Mounting brackets shelf arm
InteGrade LED
Mounting brackets shelf
InteGrade LED
connector
InteGrade LED
lock inline
spare parts
Phillips H0 screw driver2.9 mm (1/8 inch)
Products and tools
OFF
ON
12
Start

4
1
2
2
1
1
2
1
2
Connecting the LED InteGrade xtures
in the prole
3

5
1
2
1
2
3
4
5
1
2
3
4
1
2
Installation examples with various
InteGrade mounting clips and xtures
4A 4B
1
2
4C
5

6
Number of InteGrade LED xtures allowed on one driver (max allowed load is 90%)
W per fixture On a Xitaniun
20 W driver
On a Xitanium
80 W driver
InteGrade LED xture value 875mm(34") 840 8 29
InteGrade LED xture value 875mm(34") 830 8 29
InteGrade LED xture value 1175mm(46") 840 10 1 7
InteGrade LED xture value 1175 mm (46") 830 10 1 7
Tcase max. 70 °C / 158 °F
80W
Power driver and wiring
• To allow for variance in the installation, it is not recommended to load the power driver
beyond 90% of it’s rated maximum power
- Xitanium LED driver 20 W (logistic code 929000654006) max 18 W
- Xitanium LED driver 80 W (logistic code 929000653906) max 72 W
• Use Philips InteGrade LED power cable of 1 m (39 inch) or 2.5 m (98 inch)
• If InteGrade power cables are extended, only use 0.75 mm2 (AWG 18) or thicker cable uptil a
length of max 10 m (32 feet) between driver and Philips LED power cable
• Only parallel connections are advised, see table below for quantities per driver. If you wish to
make any other conguration, please contact Philips.
Parallel connections
The driver should be built-in.
Wiring diagram with Philips InteGrade LED xtures
Philips LED
Power Driver
24V DC
A B
Philips LED
Power Driver
24V DC
AB
0.75 mm2
(AWG 18)
max. 10 m
(32 feet)
InteGrade LED fixture
InteGrade LED fixture
InteGrade LED fixture
InteGrade LED fixture
InteGrade LED fixture
InteGrade LED fixture
InteGrade LED fixture
InteGrade LED fixture
InteGrade LED fixture
InteGrade LED fixture
driver cable
approx 0.3 m
(12 inch)
Philips LED
power cable
max. 2.5 m
(98 inch)
0.75 mm2
(AWG 18)
max. 10 m
(32 feet)
driver cable
approx 0.3 m
(12 inch)
Philips LED
power cable
max. 2.5 m
(98 inch)

7

©2012 Royal Philips Electronics
All rights reserved.
Form No. 3222 635 67167 US -30-+30
LE-6600-A 09/2012
www.philips.com/oem
www.philips.com/ledrefrigeration
www.philips.com/ledmodulesna / NA Customer Support/Technical Service: Tel. [phone]