Philips BVP528 User manual

BVP528 HGB
BVP528 BV
BVP518 HGB
BVP518 BV
220 V
400 V
OptiVision LED gen3.5
BVP528/BVP518
1 RG1
*Lumen maintenance at median useful life 50Khrs is L80
© 07/2020 Signify Holding. All rights reserved
Any modication on the luminaire will cancel the warranty
SCx
Performance is not guaranteed for rated NOMINAL mains voltage of below 220Vac and over 400Vac.
Tolerance for voltage uctuations: safety ±10%, performance -8/+6%, is part of the design and as per standard EN 62384.
1/24
Printed in Spain
Data subject to change without notice
Keep for future reference: www.philips.com/lighting
443000021241_A
HGB BV 90º HGB
BVP528 33 26,5 0,47
BVP518 29 22 0,33
Conguration 0º 15º 30º 40º 50º 65º 90º
BVP518 HGB 0,18 0,22 0,25 0,27 0,27 0,29 0,33
BVP518 HGB+ EXTERNAL LOUVER 0,23 0,25 0,27 0,26 0,25 0,25 0,32
BVP518 BV 0,10 0,17 0,21 0,24 0,26 0,30 0,34
BVP518 BV+EXTERNAL LOUVER 0,13 0,18 0,22 0,25 0,25 0,26 0,32
BVP528 BV 0,12 0,20 0,29 0,33 0,33 0,41 0,48
BVP528 BV+EXTERNAL LOUVER 0,14 0,24 0,29 0,31 0,34 0,38 0,44
BVP528 HGB 0,20 0,27 0,30 0,32 0,33 0,41 0,47
BVP528 HGB+EXTERNAL LOUVER 0,23 0,30 0,32 0,32 0,34 0,39 0,44
OPERATING
TEMPERATURE MAX. MIN.
OUTDOOR 45ºC -40ºC
INDOOR 45ºC -40ºC

2/24
BVP528 50000h 757 203000 1500 20ºC
BVP528 50000h 740 203000 1500 20ºC
BVP528 50000h 730 189000 1500 20ºC
BVP528 50000h 757 202000 1500 25ºC
BVP528 50000h 740 202000 1500 25ºC
BVP528 50000h 730 188000 1500 25ºC
BVP528 50000h 757 194000 1420 30ºC
BVP528 50000h 740 194000 1420 30ºC
BVP528 50000h 730 180000 1420 30ºC
BVP528 50000h 757 185000 1340 35ºC
BVP528 50000h 740 185000 1340 35ºC
BVP528 50000h 730 172000 1340 35ºC
BVP528 50000h 757 176000 1270 40ºC
BVP528 50000h 740 176000 1270 40ºC
BVP528 50000h 730 164000 1270 40ºC
BVP528 50000h 757 167000 1200 45ºC
BVP528 50000h 740 167000 1200 45ºC
BVP528 50000h 730 155000 1200 45ºC
BVP528 100000h 757 194000 1420 20ºC
BVP528 100000h 740 194000 1420 20ºC
BVP528 100000h 730 182000 1420 20ºC
BVP528 100000h 757 187000 1340 25ºC
BVP528 100000h 740 187000 1340 25ºC
BVP528 100000h 730 174000 1340 25ºC
BVP528 100000h 757 178000 1270 30ºC
BVP528 100000h 740 178000 1270 30ºC
BVP528 100000h 730 166000 1270 30ºC
BVP528 100000h 757 169000 1200 35ºC
BVP528 100000h 740 169000 1200 35ºC
BVP528 100000h 730 157000 1200 35ºC
BVP528 100000h 757 160000 1120 40ºC
BVP528 100000h 740 160000 1120 40ºC
BVP528 100000h 730 149000 1120 40ºC
BVP528 100000h 757 146000 990 45ºC
BVP528 100000h 740 146000 990 45ºC
BVP528 100000h 730 136000 990 45ºC
BVP528 50000h 757 167000 1200 35ºC
BVP528 50000h 740 167000 1200 35ºC
BVP528 50000h 757 144000 990 45ºC
BVP528 50000h 740 144000 990 45° C
BVP528 100000h 757 146000 990 35ºC
BVP528 100000h 740 146000 990 35ºC
BVP528 100000h 757 131000 880 45ºC
BVP528 100000h 740 131000 880 45° C
BVP518 50000h 757 135000 1000 20ºC
BVP518 50000h 740 135000 1000 20ºC
BVP518 50000h 730 126000 1000 20ºC
BVP518 50000h 757 134000 1000 25ºC
BVP518 50000h 740 134000 1000 25ºC
BVP518 50000h 730 125000 1000 25ºC
BVP518 50000h 757 129000 945 30ºC
BVP518 50000h 740 129000 945 30ºC
BVP518 50000h 730 120000 945 30ºC
BVP518 50000h 757 123000 895 35ºC
BVP518 50000h 740 123000 895 35ºC
BVP518 50000h 730 115000 895 35ºC
BVP518 50000h 757 117000 850 40ºC
BVP518 50000h 740 117000 850 40ºC
BVP518 50000h 730 109000 850 40ºC
BVP518 50000h 757 111000 800 45ºC
BVP518 50000h 740 111000 800 45ºC
BVP518 50000h 730 103000 800 45ºC
BVP518 100000h 757 129000 945 20ºC
BVP518 100000h 740 129000 945 20ºC
BVP518 100000h 730 120000 945 20ºC
BVP518 100000h 757 125000 895 25ºC
BVP518 100000h 740 125000 895 25ºC
BVP518 100000h 730 116000 895 25ºC
BVP518 100000h 757 119000 850 30ºC
BVP518 100000h 740 119000 850 30ºC
BVP518 100000h 730 110000 850 30ºC
BVP518 100000h 757 113000 800 35ºC
BVP518 100000h 740 113000 800 35ºC
BVP518 100000h 730 105000 800 35ºC
BVP518 100000h 757 106000 745 40ºC
BVP518 100000h 740 106000 745 40ºC
BVP518 100000h 730 99000 745 40ºC
BVP518 100000h 757 97000 660 45ºC
BVP518 100000h 740 97000 660 45ºC
BVP518 100000h 730 90000 660 45ºC
BVP518 50000h 757 111000 800 35ºC
BVP518 50000h 740 111000 800 35ºC
BVP518 50000h 757 96000 660 45ºC
BVP518 50000h 740 96000 660 45° C
BVP518 100000h 757 97000 660 35ºC
BVP518 100000h 740 97000 660 35ºC
BVP518 100000h 757 87000 585 45ºC
BVP518 100000h 740 87000 585 45° C

In luminaire version for swimming pool applications (SWP):
Fixture mounting system (including fasteners) needs to be compliant with EN
13451-1 or MIS 1203
Mounting system and product shall be a subject of periodical inspection at least
every year.
Any rusted element needs to be replaced.
The light source contained in this luminaire shall only be replaced by the manu-
facturer or his service agent or a similar qualied person.
If the external exible cable or cord of this luminaire is damaged, it shall be ex-
clusively replaced by the manufacturer or his service agent or a similar qualied
person in order to avoid a hazard
NOT ALLOWED
LIGHT FACING UP
POSITIONS ALLOWED
POSITIONS NOT ALLOWED
80º
80º
3/24

FLAT WASHER NEEDED
ACCORDING TO
DIN9021
In case of using only one xation point
and if the luminaire is higher >3m, the
use of a 2nd xing security system is
needed
The fasteners have to resist environment corrosion.
Stainless steel screws not recommended and protective coating might be
applied.
30mm
2XM20 SCREW 1XM20 SCREW
123
4If luminaire placed as
shown, rotation angle
limited (only HGB
version, BV version no
limitation):
28º<angle<76º
angle<28º or >76º


30
Attention: do not hold the luminaire by the cable gland
100
5
25
17 50
• In case of using only one screw, use uniquely the position 1. Never use
one single screw in Pos.2 or Pos.3
• If using the Pos.2, the second screw must be in the opposite Pos. 2.
• If using the Pos.3, the second screw must be in the opposite Pos. 3.
92,5mm
A cable can be used as second security system.
Section has to be enough for the installation and support
environmental conditions (e.g. sheathed steel)
4/24

PC
CLEANING TECHNIQUES
1. Always test the sample with the cleaner and
according to the chosen technique before
2. Do not leave cleaners on plastic parts for a
long period
3. Do not apply cleaners in direct sunlight or at
elevated temperatures
1. Remove physical elements that can block
and modify the aircooling (heatsink ns)
2. Cleaning Frequency (depending on installa-
tion place and environment)
CLEANING PARTS
RECOMMENDED
Mild Soap
Lukewarm Water
Soft/Grid free Cloth
Sponge
Water Cleaning
Cleaning Interval
(months)
Pollution Category
High Medium Low
12 0,91 0,92 0,93
18 0,90 0,91 0,92
24 0,88 0,89 0,91
30 0,85 0,88 0,9
36 0,83 0,87 0,9
CLEANING
The list is not exhaustive
FORBIDDEN
Abrasive Cleaners
Highly Alkaline Cleaners
Aromatic Solvents
Halogenated Solvents
Brushes
Steel Wood
S3
S4
S6
S6
5/24

ACCESSORIES
12NC: 912300024868 ZVP418 EXTERNAL LOUVER
LOUVRE (External louvre (1 per module, 2 or 3 pieces per luminaire)
PRECISION AIMING DEVICE
12NC: 912300024470 AIMING DEVICE WITHOUT VISOR
3
123
TURN TO CORRECT POSITION
3
4a 5a 6a
12
12x screws to
be removed
12x screws
BVP528
4b 5b 6b
BVP518
20 1.6
Always align the direc-
tion TOP and BOTTOM
when installing the
louver
6/24

CHANGE FROM BV TO HGB
CONNECTIONS IN NEXT SLIDES
COMPONENT TORQUE TOOL
SCREW M5 (4X)
SCREW M10 (2X)
WASHER -
CABLE SEE 8-9
25 3.5
17 50
12NC
912300024570 A AVOV G3 RAW DRV SUPPORT V2 AND CABLE
912300024571 A AVOV G3 LGR DRV SUPPORT V2 AND CABLE
912300024572 A AVOV G3 DGR DRV SUPPORT V2 AND CABLE
GEN 3 BRACKET
7/24

EVP500
OptiVision LED gen3.5
Driver box
EVP500
145
500
477
129
120
Iin (Mains 220V-240V) 8A
Iin (Mains 380V-400V) 4.6A
Inrush (220V-240V) 20 A during 160 µs
Inrush (380V-400V) 30 A during 160 µs
Power Factor > 0.95 at full power
Surge Protection* 10kV Com. Mode
6kV Dif. Mode
Maximum Heat Disipation** 75W
Driver box Features
L<50 page 9
50<L<200 page 12
Distances between driver and luminaire
-40
45
** According to the maximum
heat disipation, a thermal
study should be done for a
cabinet installation
* A surge protection device should
be integrated in the installation
before the luminaire
6,3
L
220 V
400 V
8/24

ELECTRICAL CONNECTION FOR EVP500 DALI L< 50m
a
CONNECTION
BOX DALI
MAINS MAINS CONNECTION
BOX
Cable from Driver box
to Connection Box
MAINS
DALI
b
Ø min
(mm)
Ø max
(mm)
TORQUE MAX VOLTAGE
SUPPORTED
RECOMMENDED CABLE TYPE CONNECTOR
SECTION
MAX
DALI Cable M20 Ø6Ø12 3 Nm 1000 V
H05VV-F (3182-Y) 2
core x 1.5mm or H05VV-F (3182-Y) 2
core x 2.5mm
2.5 mm2
MAINS Cable M25 Ø13 Ø18 5 Nm 1000 V H07RN-F 450V/750V 4 mm2
Connection Box M25 Ø13 Ø18 4.5 Nm 1000 V H07RN-F 450V/750 or A11VV U-600/1000V 2.5 mm2
20 1.6 L
9/24
STRIPPING LENGTH:
8-9 mm
8-9 mm

ELECTRICAL CONNECTION L< 50m (only on special requests)
MAINS
Cable from Driver box
to Connection Box
DMX (2 entries)
Ø min
(mm)
Ø max
(mm)
TORQUE MAX VOLTAGE
SUPPORTED
RECOMMENDED CABLE TYPE CONNECTOR
SECTION MAX
DMX Cable M20 2 x Ø6mm
+/-1mm NA 4.5 Nm 1000 V 2x ETHERNET shielded cable CAT5
MAINS Cable M25 Ø13 Ø18 5 Nm 1000 V H07RN-F 450V/750V 4 mm2
Connection Box M25 Ø13 Ø18 4.5 Nm 1000 V H07RN-F 450V/750 or A11VV U-600/1000V 2.5 mm2
TERMINATOR RJ45 (not supplied by Philips)
For safety reasons the terminator must have
isolated housing
CONNECTION BOX
DMX
1) Remove plugs only when needed
2) Slip the DMX cable without RJ45
plug through the cable gland
3) Crimp the RJ45 modular plug on
the DMX cable inside the driver
MAINS
Ø13-18mm
Pin numbering and color in accordance with ANSI/TIA/EIA-568
scheme T568B
PIN # COLOR FUNCTION
1 WHITE/ORANGE DATA 1+
2 ORANGE DATA 1-
3 WHITE/GREEN DATA 2+ (Optional)
6 GREEN DATA 2- (Optional)
4 BLUE Not assigned
5 WHITE/BLUE Not assigned
7 WHITE/BROWN Signal Common for data 1 (0 V)
8 BROWN Signal Common for Data 2 (0 V)
9 DRAIN
20 1.6 L
10/24
STRIPPING LENGTH:
8-9 mm
8-9 mm