PICOTE Small Grabber Value Use and care manual

MINI CLEANER
SUPER MIDI MILLER 8/16 | SUPER MIDI MILLER
These instrucons are for your personal safety. Always ensure that you
have read and understood these instrucons before using the machinery.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
SMALL GRABBER
OPERATION & SAFETY MANUAL

2www.picoteinstute.com
TABLE OF CONTENTS
To watch praccal demonstraon videos, take a course, or to download an electronic copy of these Instrucons, please visit www.picoteinstute.com.
Please note that videos and courses are not intended as a replacement or alternave to this operang and safety manual, but only as an addional learning tool.
TOPIC PAGE
General Safety Informaon 3
Storage & Disposal 4
General Informaon & Intended use 5
Operang Instrucons 6
Changing The Jaws 7
Maintenance 8
Repairing Damaged Cable (Jaw End) 9
Repairing Damaged Cable (Handle End) 13
Accessories, Spares & Recommended Parts 17
Warranty Policy & Procedure 18

Personal Protecve Equipment (PPE)
Always use Personal Protecve Equipment including suitable protecve clothing, footwear, plus:
Suitable eye protecon to protect against sewage, chemicals or dust from irritang
eyes.
Suitable heat and cut-resistant gloves to help prevent any hand injuries. Any open
injuries or skin irritaons should always be covered to avoid contact with sewage,
chemicals or dust.
www.picotesoluons.com www.picoteinstute.com 3
Picote Soluons Oy Ltd
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
GENERAL SAFETY INFORMATION
Always read all safety warnings and instrucons. Failure to follow warnings and instrucons may result in serious
injury.
This secon contains important safety informaon. Failure to comply could result in serious injury.
1. Always wear eye protecon as well as heat and cut-resistant gloves.
Other personal protecve equipment, such as dust mask, gloves and overalls should be worn when necessary.
Dust produced when working can be dangerous to your health, inammable or explosive.
Always wear appropriate personal protecve equipment.
2. Before each use inspect the Grabber and Jaws carefully for any potenal break or damage. Change damaged
parts immediately.
3. Only use this tool with the accessories and spare parts oered by the Picote Soluons. Accessories and spare
parts should only be used in the manner intended and as described by Picote Soluons.

STORAGE
It is recommended that the Small Grabber is stored indoors to protect it from rain and sunlight and also in a constant
ambient temperature. It is recommended that the 5m (16) long Small Grabber is stored in a coil with two turns and
the 10m (32) long Small Grabber in four turns.
DISPOSAL
The Jaw set, wire and handle can be recycled in metal waste collecon points. The plasc outer casing of the sha can
be disposed of as plasc waste.
Always follow your local waste handling rules and regulaons.
This secon contains important safety informaon. Failure to comply could result in serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
STORAGE & DISPOSAL
10
4Picote Soluons Oy Ltd www.picoteinstute.com

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
GENERAL INFORMATION & INTENDED USE
6
www.picoteinstute.com Picote Soluons Oy Ltd
5
1. Retrieving lost items or foreign objects from inside a pipe.
INTENDED USE
SMALL GRABBER
2370000020 Small Grabber Value DN50-75 (2-3”) 5m (16) Model 1 Jaw Type (Paw)
2370000021 Small Grabber Value DN50-75 (2-3”) 10m (32) Model 1 Jaw Type (Paw)
2370000022 Small Grabber Extra DN50-75 (2-3”) 5m (16) Model 1 (Paw) and Model 2 (Claw) Jaw types
2370000023 Small Grabber Extra DN50-75 (2-3”) 10m (32) Model 1 (Paw) and Model 2 (Claw) Jaw types
Two lengths available: 5m (16) & 10m (32). No extension available.
Two models of Jaw set for dierent uses: Model 1 (Paw) & Model 2 (Claw).
Two packages are available: Extra with 4 Jaws (with both Models 1 & 2) and Value with 2 Jaws (Model 1 only).

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
OPERATING INSTRUCTIONS
1. To close the Jaws, rotate the handle clockwise.
2. To open the Jaws, rotate the handle counter clockwise.
NOTE! The Small Grabber should only be used in an uncoiled posion. Excessive use of
force may result in the tool breaking!
10
6Picote Soluons Oy Ltd www.picoteinstute.com

www.picoteinstute.com Picote Soluons Oy Ltd
7
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
OPERATING INSTRUCTIONS
CHANGING THE JAWS
1. Use a 2.5mm hex key to unscrew both screws at the Jaw
2. Take out the Jaws and re-assemble in reverse order

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
MAINTENANCE
10
8Picote Soluons Oy Ltd www.picoteinstute.com
Clean any dirt from the screw handle and
lubricate the threads with vaseline aer
each use.
Clean dirt from the Jaw mechanism and
lubricate it with oil aer each use.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
REPAIRING DAMAGED CABLE - JAW END
www.picoteinstute.com Picote Soluons Oy Ltd
9
1. Use 2.5mm hex key to unscrew both screws at the Jaw
2. Take out the Jaws
3. Use 2mm and 3mm hex keys to unscrew the set screw to remove the wire holder and spring

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
REPAIRING DAMAGED CABLE - JAW END
14
4. Use a wrench to remove the Jaw Head
5. Carefully cut the outer casing. Avoid cung the wire inside. Cut at least 25mm (1”) or unl you
have no damaged wire le.
6. Trim the wire. 7. Pull the wire inside its casing—it should
measure at least the same length as the
trimmed outer casing.
10
10 Picote Soluons Oy Ltd www.picoteinstute.com

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
REPAIRING DAMAGED CABLE - JAW END
www.picoteinstute.com Picote Soluons Oy Ltd
11
14
8. Trim the inner casing to the same length as the outer casing. Approximately 5mm (0.2”) of the inner
casing should be showing (see below). Push the wire back inside and screw the handle all the way in.
9. Screw the Jaw Head back on to the outer casing. A vice helps hold it in place.
10. Replace the spring and the wire holder.
Do not ghten the wire holder yet.
11. Put the Jaws back and ghten the Jaw
screws.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
REPAIRING DAMAGED CABLE - JAW END
12. Pull the wire to remove any loose wire. Tighten the set screw.
13. Test that the tool works and trim the excess wire.
10
12 Picote Soluons Oy Ltd www.picoteinstute.com

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
REPAIRING A DAMAGED CABLE - HANDLE END
www.picoteinstute.com Picote Soluons Oy Ltd
13
1. Use 2.5mm hex key to unscrew both screws at the Jaw end
2. Remove the Jaws
3. Use 1.5mm hex key to unscrew both set screws from the end cap.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
REPAIRING A DAMAGED CABLE - HANDLE END
4. Take out the bearing and unscrew the handle from the outer casing
5. Carefully cut the outer casing. Avoid
cung the wire inside. Cut at least 25mm
(1”) or unl there is no damaged wire le.
6. Pull the wire at the Jaw end and trim the
inner casing to the same length as the outer
casing. Approximately 5mm (0.2”) of the
inner casing should be showing.
7. Push the wire back in and screw the handle back on to the outer casing. A vice helps hold it in
place.
10
14 Picote Soluons Oy Ltd www.picoteinstute.com

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
REPAIRING A DAMAGED CABLE - HANDLE END
www.picoteinstute.com Picote Soluons Oy Ltd
15
8. Re-assemble the handle in reverse order
9. Put the end cap back but don’t push the wire completely through the end cap to avoid sharp edges!

If there is problem that you cannot resolve with this manual, please consult your Picote
Reseller or Picote Solutions.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
REPAIRING A DAMAGED CABLE - HANDLE END
10. Loosen the set screw at the wire holder
12. Pull the wire to remove any loose wire at the handle end. Tighten the set screw.
11. Put the Jaws back and ghten the screws.
13. Test the tool works and trim the excess wire.
10
16 Picote Soluons Oy Ltd www.picoteinstute.com

SMALL GRABBER
2370000020 Small Grabber Value DN50-75 (2-3”) 5m (16) Model 1 Jaws (Paw)
2370000021 Small Grabber Value DN50-75 (2-3”) 10m (32) Model 1 Jaws (Paw)
2370000022 Small Grabber Extra DN50-75 (2-3”) 5m (16) with Model 1 (Paw) and Model 2 (Claw) Jaws
2370000023 Small Grabber Extra DN50-75 (2-3”) 10m (32) with Model 1 (Paw) and Model 2 (Claw) Jaws
SPARE PARTS
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
ACCESSORIES, SPARES & RECOMMENDED PARTS
You must use only Picote Soluons accessories and aachments with the Product described in this
operaons manual. The use of other accessories or aachments could present a risk of injury.
The accessories or aachments should only be used in the proper and intended manner. Always
follow Picote Soluons instrucons.
10
17 Picote Soluons Oy Ltd www.picoteinstute.com
2370000024 Small Grabber Jaw Set 1 (Paw) for DN50 (2”)
2370000025 Small Grabber Jaw Set 2 (Claw) for DN50 (2”)
2370000026 Small Grabber Jaw Set 1 (Paw) for DN75 (3”)
2370000027 Small Grabber Jaw Set 2 (Claw) for DN75 (3”)
www.picoteinstute.com Picote Soluons Oy Ltd
17
The Small Grabber comes with the Model 1 Jaw (Paw) as standard. The
DN50 (2”) head is pre-aached. The Paw is perfect for grabbing most
items with a larger surface area where you cannot get the jaw all the
way around the object. Also ideal for objects with smoother surfaces
which can be harder to grab.
Model 1 Jaw (Paw)
Model 2 Jaw (Claw)
You can buy the Model 2 Jaws (Claws) separately or as part of the Extra
package. The jaws of the Claw overlap so that they can fully encompass
a smaller object or a smaller part of an object (for example a chain link).
RECOMMENDATION
Always use a CCTV Camera while operang the Small Grabber.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
WARRANTY POLICY & PROCEDURE
Limited Warranty:
Picote warrants to the original End User that the Product purchased by such End User will operate in
accordance with, and substanally conform to their published specicaons when shipped or otherwise
delivered to the End User and for a period of one (1) year, except electric motors for which the warranty
period shall be six (6) months, provided, however, that Picote does not warrant any claim or damage under
this Warranty if such claim or damage results from:
1. Consumable parts or normal wear and tear resulng from use of the Products,
2. Product overload or overheated motor,
3. Regular periodic maintenance of Products,
4. Misuse, neglect, or improper installaon or maintenance of the Products, or use of Products
not for their intended purpose,
5. Products that have been altered, modied, repaired, opened or tampered with by anyone
other than Picote or an authorized Picote Service Centre, or unsuitable or unauthorized spare
parts, accessories or third party products when using the Products or;
6. the use of the Products not in compliance with their respecve Documentaon, user manuals,
safety and maintenance instrucons, and any usage restricons contained therein, or
7. accident, re, power failure, power surge, or other hazard.
Otherwise, the Products are sold AS IS. End User is responsible for using the Products within
their specicaons and instrucons as contained in the Documentaon.
EXCEPT AS SPECIFIED IN THIS WARRANTY, ALL EXPRESS OR IMPLIED CONDITIONS,
REPRESENTATIONS, AND WARRANTIES INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY OR
CONDITION OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NON INFRINGEMENT,
SATISFACTORY QUALITY OR ARISING FROM A COURSE OF DEALING, LAW, USAGE, OR TRADE PRACTICE,
ARE HEREBY EXCLUDED TO THE EXTENT ALLOWED BY APPLICABLE LAW. TO THE EXTENT AN IMPLIED
WARRANTY CANNOT BE EXCLUDED, SUCH WARRANTY IS LIMITED IN DURATION TO THE WARRANTY
PERIOD. BECAUSE SOME STATES OR JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS, THE ABOVE LIMITATION MAY NOT APPLY. This disclaimer and exclusion shall
apply even if the express warranty set forth above fails of its essenal purpose.
10
18 Picote Soluons Oy Ltd www.picoteinstute.com

Revision number: Rev. 1
Author: Ville Hukkanen
Accepted: Dawn Greig
Date: JAN. 2021
Please Contact:
Your Reseller / Salesperson or Picote
www.picotesoluons.com
Finland. United Kingdom. USA.
Authorised Resellers:
www.picotesoluons.com/resellers
support@picotesoluons.com Pienteollisuuse 24
06450 Porvoo, Finland
support@picotesoluons.com
Producon & R&D
Internaonal Oces Technical Support
Claims
claims@picotesoluons.com