Pioneer ND-PS1 User manual

Manual ND-PS1
Parking Sensor

Warning
• Consultyourdealerifinstallationrequiresdrillingofholesorother
modificationstothevehicle.
• Donotattempttoinstallorservicethisproductbyyourself.
Installationorservicingofthisproductbypersonswithouttraining
andexperienceinelectronicequipmentandautomotive
accessoriesmaybedangerousandcouldexposeyoutotheriskof
electricshock,injury,orotherhazards.
• ThisproductisareversingaidandPioneeracceptsno
responsibilityforanylossordamageofanykindincurredasaresult
oftheuseofthesensors.

SAFETY STANDARD
CAUTION
Thisproductisevaluatedinmoderateand
tropicalclimateconditionundertheAudio,
videoandsimilarelectronicapparatus
-Safetyrequirements,IEC60065.
Thegraphicalsymbol placedonthe
productmeansdirectcurrent.

NOTES
• Thecarmustbepoweredoffduringtheinstallationofthedevice.
• Thesensorsmaybeaffectedinthefollowingsituations:
heavyrain,gravelroad,bumpyroad,slopingroad,grassyroad,verycoldorhotweather,moistweather,thesensorsarecoveredbysnow
orice,etc.
• Thesensorsshouldbeinstalledappropriately.
• Donotinstallthesensorsonametallicbumper.
• Avoidinstallingthecontrolboxinornearventpipeorwiring.
• Makesurethatthedeviceworksproperlybeforeandafterinstallingthisproduct.<TestMethod:RefertoTESTBEFOREINSTALLATION>

LIMITATIONS
Fig 1:Thedisplaymaynotbethesameastherealconditiondueto
thesensorposition,obstacle,shape,reflectioncondition,andsoon.
 Ifanobjectistoohigh
 Ifthereisaverysmallobject
 Whenbackingupdownhill
Fig 2:Objectshardtobedetectedinthefollowingconditions.
 Smoothslope
 Smoothroundobjects
 Objectsthatabsorbwaves(e.g.cotton)
Fig 1
Fig 2

GENERAL INSTALLATION DIAGRAM
 Controlbox
 Sensor
 Pioneercompatibleunit
(soldseparately)
 Powercable
 Connectioncable
 Holesaw

WIRING DIAGRAM
 Reversinglight(Red)
 Ground(Black)
 Tothecompatibleunit

TEST BEFORE INSTALLATION
Testthedistancewithahardplateof100cm × 100cmorawall.
Thefarthestdetectiondistanceis2.5m.(Theshortestdetection
distanceis30cm).Makesuretochecktheoperationbeforethe
installation.
2.5 m

SENSOR INSTALLATION
Fig 1:Presetofsensorinstallationheightis
55-65cmverticallytotheground.
Fig 2:Applytheadhesivepapertothe
appropriateheightpositionofthesensor,
andthenmeasuretheinstallationposition
ofthe4sensorsandmarkwithapen.
Fig 1
Fig 2
55 cm 65 cm
40 cm 40 cm
20 cm 20 cm

SENSOR INSTALLATION2
Fig 1:Installthe19mmholesaw(supplied)intotheelectricdrill
anddrilltheholesinthemarked4positions.
Fig 2:Insertthesensorsintotheholesonebyoneandtighten
them.
Caution
Neverpaintonthesensors.Itisquitedifficulttoreceiveultrasonic
waves.
NOTES
• Makesurethearrowdirectionpointsupwardwheninsertingthe
sensorintothehole.
• Makesuretoinstallthesensorssnugly.
Fig 2
Fig 1
19 mm

CONTROL BOX INSTALLATION
Theredwireisconnectedtothepositiveofthereversinglightand
theblackwireisconnectedtotheground.Usetheinsulationtape
tocoverthejointwhichisconnectedbysolderingiron.
 Ground(Black)
 Reversinglight(Red)

CONTROL BOX INSTALLATION

SPECIFICATION
Control box specification
Nominalvoltage:14.4VDC
Operatingvoltage:10.8~15.1VDC
Ratedcurrent:10~30mAat14.4VDC
Detectionrange:0.3m~2.5m
Operationtemperaturerange:-20˚C~70˚C
Dimensions(WxHxD):105.3mm × 
21.8mm × 56.0mm
Weight:52g
Cable length
Powercable:1m
Connectioncable:5m
Sensor Specifications
Centerfrequency:40kHz
DirectivityX-axis:70°
DirectivityY-axis:70°
Maximuninputvoltage:120Vp-p
(at40kHz)
IPcode:IP67
Operationtemperaturerange:-30˚C~80˚C
Dimensions:φ23.5mm×19.8mm
(Excludecable)
Weight:50g/1pc
Cablelength:2.5m
Learn more about cameras and driver safety we have.