Planet ICA-151 User manual

Dual Mode Internet Camera
ICA-151 / ICA-750
Quick Installation Guide

Table of Contents
Chapter 1. Introduction .................................................................................... 3
1.1 Before Installation................................................................................. 3
Chapter 2. ICA-151 – Dual Mode CMOS IP Camera ............................................ 4
2.1 Package Content................................................................................... 4
2.2 Outlook................................................................................................ 4
2.2.1 Front Panel................................................................................. 4
2.2.2 Rear Panel.................................................................................. 5
2.3 Physical Installation ............................................................................. 6
Chapter 3. ICA-750 Dual Mode CCD Box IP Camera ........................................... 7
3.1 Package Content................................................................................... 7
3.2 Outlook................................................................................................ 7
3.2.1 Front Panel................................................................................. 7
3.2.2 Rear Panel.................................................................................. 8
3.3 Physical Installation............................................................................... 8
Chapter 4. Setup Wizard Installation and operation ............................................ 9
Chapter 5. Cam Viewer Plus Installation ...........................................................16
Appendix A: Feature Listing for Cam Viewer Plus...............................................21
Appendix B: Suggest Hardware / System Requirement ......................................22
Ordering Information for Cam Viewer Plus Pro .............................................23
Further Conguration .................................................................................23

3
Chapter 1. Introduction
Thank you for purchasing the IP surveillance product. It is versatile and high image
solution of the perfect surveillance application. The IP surveillance state-of-art
design is considerable to t in various network environments.
1.1 Before Installation
Before installation, please be sure to read this quick installation guide and user’s
manual (CD) carefully to complete machine installation.
This QIG includes the following chapter:
• Chapter 2. ICA-151 – Dual Mode CMOS IP Camera
• Chapter 3. ICA-750 – Dual Mode CCD Box IP Camera
• Chapter 4. Setup Wizard Installation and operation
• Chapter 5. Cam Viewer Plus Installation
• Appendix A: Feature Listing for Cam Viewer Plus
• Appendix B: Suggest Hardware / System Requirement

4
Chapter 2. ICA-151 – Dual Mode CMOS IP Camera
2.1 Package Content
ICA-151 x 1
Power Adapter x 1
Camera Stand x 1
CD Disk x 1
Quick Installation Guide x 1
Note
1. If any of the above items are missing, please contact your
dealer immediately.
2. Using a power supply with a different voltage that the one
included with the package will cause damage and void the
warranty.
2.2 Outlook
2.2.1 Front Panel
Microphone
PWR LAN
ACT
LED Status LED Description
PWR
Off No power.
On Power on.
Blinking The Power LED will blink during start up (15 ~ 20 sec).
ACT Off Camera is not capturing video.
Blinking Camera is capturing video.
LAN Off LAN is not connected or camera is not sending/receiving data.
Blinking Data is being transmitted or received via the LAN connection.

5
2.2.2 Rear Panel
AUDIO OUT PWR LAN
PORT PORT Description
AUDIO OUT An external speaker can be plugged in.
PWR Connect the supplied power adapter.
LAN Connect your Camera to a 10/100Base-TX hub or switch.
Reset
Reset to manufacturer default valued and reboot.
When pressed and held over 10 seconds, the settings of IP
Camera will be set to the default values.
Upon completion, the PWE LED will blink three times.
Bottom Panel of ICA-151

6
2.3 Physical Installation
1. Connect an Ethernet cable
Connect one end of an Ethernet cable to the LAN port located on the IP camera’s
rear panel and connect the other end to the network device (hub or switch).
2. Attach the external power supply
Attach the provided power adapter to the IP camera’s connector labeled “PWR”
on the rear panel.
3. Check the LEDs
a. The Power LED will turn on briey, and then start blinking during startup.
After startup is completed, the Power LED will remain ON.
b. The LAN LED will be ON.

7
Chapter 3. ICA-750 Dual Mode CCD Box IP Camera
3.1 Package Content
ICA-750 x 1
Power Adapter x 1
CD Disk x 1
Quick Installation Guide x 1
Allen Wrench x 1
Camera Stand x 1
Note
1. if any of the above items are missing, please contact your dealer
immediately.
2. Using a power supply with a different voltage that the one
included with the package will cause damage and void the
warranty.
3.2 Outlook
3.2.1 Front Panel
DC-drive type
Auto Iris Lens Connector
LAN
Microphone
PWR
LED Status LED Description
PWR
Off No power.
On Power on.
Blinking The Power LED will blink during start up (15 ~ 20 sec).
LAN
Off LAN connection is not detected.
On LAN connection is detected.
Blinking Data is being transmitted or received via the LAN connection.

8
3.2.2 Rear Panel
Reset LAN (PoE)
PWR AUDIO IN
AUDIO OUT
DI / DO
I/O Info
PORT PORT Description
Reset
Reset to manufacturer default valued and reboot.
When pressed and held over 10 seconds, the settings of IP
Camera will be set to the default values.
Upon completion, the PWE LED will blink three times.
LAN (PoE)
Connect your Camera to a 10/100Base-TX hub or switch. This
interface compliant with IEEE802.3af standard PoE PD (Powered
Device). Either mid-span & end-span PSE can be used.
PWR
Connect to the supplied power adapter 12V DC, 1A. When this
device is obtaining power from PoE already, you don’t have to
attach the power adapter to ICA-750.
DI / DO The terminal block includes 2 input ports and 2 output ports.
AUDIO IN An external microphone can be plugged in. That will disable the
built-in microphone on the front panel.
AUDIO OUT An external speaker can be plugged in.
3.3 Physical Installation
1. Connect an Ethernet cable
Connect one end of an Ethernet cable to the LAN port located on the IP camera’s
rear panel and connect the other end to the network device (hub or switch).
2. Attach the external power supply
Attach the provided power adapter to the IP camera’s connector labeled “PWR”
on the rear panel.
3. Check the LEDs
a. The Power LED will turn on briey, and then start blinking during startup.
After startup is completed, the Power LED will remain ON.
b. The LAN LED will be ON.

9
Chapter 4. Setup Wizard Installation and operation
This chapter shows how to quick set up your IP surveillance product. The IP
surveillance product is with the default settings. However to help you nd the
networked camera quickly the windows utility-IP Wizard can search the cameras in
the network that shall help you to congure some basic setting before you started
advanced management and monitoring.
Note
In the installation steps below, this guide use ICA-151 as the
example. However, the steps for ICA-750 are similar.
I Initial setup should be performed by using the supplied Windows-based Setup
Wizard as follows:
1. Insert the bundled Product CD into CD-ROM drive to launch the autorun
program.
2. After the web page displayed, click the “Setup Wizard” hyperlink on the menu
to start the conguration process.
Note
If the CD’s menu does not appear, click “Start” on the task bar
and select “Run” to type “X:\Utility\SetupWizard\SetupWizard.
exe”, assume X is your CD-Rom drive.
3. The welcome screen appears. Click on “Setup Camera” button to start the
wizard.

10
4. After clicking the setup camera button, it will auto search for the IP Cameras on
your network. Click on to continue.
5. The next screen below will list the IP Camera on your network. Select it from
the list on the left side, the current settings table will be displayed on the right
side. Click on to continue.