Planet ICA-5250V User manual

Vandalproof IR IP Camera
ICA-5250V / ICA-5260V / ICA-5550V
Quick Installation Guide

Table of Contents
Chapter 1. Introduction .................................................................................... 3
1.1 Before Installation ............................................................................... 3
1.2 System Requirements .......................................................................... 3
Chapter 2. Physical Description and Installation.................................................. 4
2.1 Package Contents ................................................................................ 4
2.2 Physical Details ................................................................................... 4
2.3 I/O Control Instruction......................................................................... 5
2.3.1 I/O Connection........................................................................... 6
2.3.2 I/OPINdenition ....................................................................... 6
2.4 Factory Default.................................................................................... 6
Chapter 3. Camera Windows Utility ................................................................... 8
3.1 IP Assignment..................................................................................... 8
Further Information ........................................................................................12

3
Chapter 1. Introduction
Thank you for purchasing PLANET Vandalproof IR IP camera. It is versatile
and high image solution of surveillance application for day and night. PLANET
IP Camera supports Multi-Prole function for simultaneous video streams.
These Network Cameras can generate H.264, MPEG-4 and M-JPEG streaming
simultaneously to different clients. Moreover, the resolution can be different from
one client to another. This state-of-art design is considerable to t in various
network environments.
This installation guide provides instructions for installing the following network
cameras:
zICA-5250V – Full HD Vandalproof IR IP Camera
zICA-5260V – 60fps Full HD Vandalproof IR IP Camera
zICA-5550V – 5 Mega-pixel Vandalproof IR IP Camera
1.1 Before Installation
Before installation, please be sure to read this quick installation guide and user’s
manual (CD) carefully to complete machine installation. This guide shows how to
quickly set up the IP camera.
1.2 System Requirements
CPU Intel Core i3-530
RAM 2048MB
Graphic Card 512MB
Display Resolution 1920 x 1200
Operating System Windows 2000, XP, 2003, Vista 32bit, Win7 32bit
Network Ethernet 10/100Base-TX

4
Chapter 2. Physical Description and Installation
2.1 Package Contents
zCamera Unit x 1
zPower Adapter x 1
zAccessories Kit x 1
zFemale to Female RJ45 Connector x 1
zMounting Label x 1
zUser’s Manual CD-ROM x 1
zQuick Installation Guide x 1
zDesiccant x 1
2.2 Physical Details
1. RJ-45 LAN Socket: Connect to PC or Hub/Switch.
When connecting to 10Base-T Ethernet or 100Base-TX Fast Ethernet cable, this
Ethernet port built N-Way protocol can detect or negotiate the transmission speed
of the network automatically. Please use CAT-5 cable to connect the Network
Camera to a 100Mbps Fast Ethernet network switch or hub.
2. Power Jack: The input power is 12V DC.
Power Jack
RJ-45

5
Note
1. To ensure maximum compatibility, use only the power adapter
that came with your product. Otherwise, the product may be
damaged.
2. The RJ45 port also supports IEEE 802.3af Power over Ethernet.
Apply either PoE or DC power to empower the IP camera and do
not use any other non-standard PoE injector to the camera.
2.3 I/O Control Instruction
I/O terminal connector is used for such functions as motion detection, and event
triggering.
RJ45
Micro SD
DEFAULT
DC
GND
GND
DO
DI
Line_OUT
MIC_IN
GND
VIDEO

6
2.3.1 I/O Connection
Please connect the GND & DO pin to the external relay (buzzer) device.
Please connect the GND & DI pin to the external trigger device.
2.3.2 I/OPINdenition
zGND (Ground): Initial status is Low
zDO (Digital Output): 5V DC
zDI (Digital Input): Max. 50mA, 5V DC
2.4 Factory Default
If you forget your password, please follow the steps to revert back to default
value.
1. Remove the power and Ethernet cable. Press and hold the button as shown in
the picture below.

7
2. Connect power to the camera again, and do not release the button during the
system booting.
3. It will take around 30 seconds to boot the camera.
4.Releasethebuttonwhencameranishesprocess.
5. Plug in the Ethernet cable, and re-login the camera using the default IP
(http://192.168.0.20), and user name (admin) and password (admin).
Note
If the dome housing is opened during installation, open the
package containing the silica gel and place it inside the dome for
avoiding humidity.
Step 1

Step 2 Step 3

8
Chapter 3. Camera Windows Utility
This chapter shows how to quickly set up your PLANET IP Camera. PLANET IP
Camera is with the default settings. However, to help you nd the networked
camera quickly, the windows utility (PLANET IP Installer) can search the cameras
in the network that will help you to congure some basic setting before you start
advanced management and monitoring.
Please insert the bundled CD disk into your CD/DVD-ROM drive. When the
welcome web page appears, please click your IP camera name on the IP camera
list. Then click the PLANET IPInstaller hyperlink to start the PLANET IP Installer.
3.1 IP Assignment
1. Use “IP Installer II” to assign an IP address of IP CAMERA.
The IP Installer software is in the attached CD.
2. IP Installer supports languages.
IPInstallerEng.exe
3. OS: Windows XP SP2 or above. If the following “Windows Security
Alert” pops out, please click “Unblock”.

9
4. The GUI of IP Installer is as follows (Default IP: 192.168.0.20).
zIP Installer will search all IP Cameras connected on LAN. The user can click
“Search Device” to search again.
zClick one of IP Cameras listed on the left side of IP Installer, then the network
conguration of that IP Camera will be listed on the right side. If parameters
change, click on “Submit”. Then, the network conguration will be changed.
Just click “OK” to reboot.
Please make sure the subnet of PC IP address and IP CAM IP address are the
same.
For Example:
IP CAM IP address: 192.168.0.20
PC IP address: 192.168.0.100
To Change PC IP addresses:
Control Panel  Network Connections  Local Area Connection Properties  Internet
Protocol (TCP/IP)  Properties

10
Please make sure your IP Camera and PC have the same subnet. If not, please
change IP Camera IP subnet or PC IP subnet accordingly.
zA quick way to access remote monitoring is to left-click the mouse twice on a
selected IP Camera listed on “Device list” of IP Installer. An IE browser will be
opened.
zThen, please key in the default User name: “admin” and Password: “admin” in
the following message box.