Planet GT-915A User manual

User’s Manual of GT-915A
1
10/100/1000BASE-T to
100/1000BASE-X SFP Managed Media
Converter
GT-915A

User’s Manual of GT-915A
2
Trademarks
Copyright © PLANET Technology Corp. 2023.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no
warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for
a particular purpose. PLANET has made every effort to ensure that this User's Manual is accurate; PLANET disclaims liability
for any inaccuracies or omissions that may have occurred.
Information in this User's Manual is subject to change without notice and does not represent a commitment on the part of
PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User's Manual. PLANET makes
no commitment to update or keep current the information in this User's Manual, and reserves the right to make improvements to
this User's Manual and/or to the products described in this User's Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and
suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class Adigital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
CE Mark Warning
This device is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference.
Energy Saving Note of the Device
This power required device does not support Standby mode operation. For energy saving, please remove the power cable to
disconnect the device from the power circuit. In view of saving the energy and reducing the unnecessary power consumption, it
is strongly suggested to remove the power connection for the device if this device is not intended to be active.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET 10/100/1000BASE-T to 100/1000BASE-X SFP Managed Media Converter User's Manual
FOR MODELS: GT-915A
REVISION: 1.0 (February, 2023)
Part No: EM-GT-915A_v1.0

User’s Manual of GT-915A
3
TABLE OF CONETNTS
1. INTRODUCTION....................................................................................................................6
1.2 Product Description.....................................................................................................................................7
1.3 How to Use This Manual............................................................................................................................10
1.4 Product Features........................................................................................................................................11
1.5 Product Specifications ..............................................................................................................................13
2. INSTALLATION ................................................................................................................... 16
2.1 Hardware Description................................................................................................................................16
2.1.1 Converter Front Panel.........................................................................................................................................16
2.1.2 Converter LED Indicators ....................................................................................................................................17
2.1.3 Rear Panel...........................................................................................................................................................18
2.1.4 Power Information ...............................................................................................................................................18
2.2 Media Converter Installation.....................................................................................................................19
2.2.1 Stand-alone Installation.......................................................................................................................................19
2.2.2 Wall-mount Installation ........................................................................................................................................19
2.2.3 Media Chassis Installation...................................................................................................................................20
2.2.4 Installing the SFP Transceiver.............................................................................................................................21
3. MEDIA CONVERTER MANAGEMENT ...............................................................................24
3.1 Requirements .............................................................................................................................................24
3.2 Management Access Overview.................................................................................................................24
3.3 Web Management.......................................................................................................................................25
3.4 SNMP-Based Network Management.........................................................................................................26
3.5 PLANET Smart Discovery Utility ..............................................................................................................27
4. WEB CONFIGURATION......................................................................................................29
4.1 Main Web Page ...........................................................................................................................................32
4.2 System.........................................................................................................................................................35
4.2.1 Management........................................................................................................................................................36
4.2.1.1 System Information....................................................................................................................................36
4.2.1.2 System Configuration................................................................................................................................37
4.2.1.3 Device Information.....................................................................................................................................38

User’s Manual of GT-915A
4
4.2.1.4 Users Configuration...................................................................................................................................38
4.2.1.5 CPU Resource Utilization..........................................................................................................................39
4.2.1.6 Syslog Settings..........................................................................................................................................40
4.2.1.7 System Log ...............................................................................................................................................41
4.2.2 IP Configuration...................................................................................................................................................42
4.2.2.1 IPv4...........................................................................................................................................................42
4.2.2.2 IPv6...........................................................................................................................................................42
4.2.3 SNMP Settings....................................................................................................................................................43
4.2.3.1 SNMP Configuration..................................................................................................................................44
4.2.3.2 SNMP View Table......................................................................................................................................44
4.2.3.3 SNMP Group Table....................................................................................................................................46
4.2.3.4 SNMP User Table......................................................................................................................................47
4.2.3.5 SNMP Community Table............................................................................................................................48
4.2.3.6 SNMP Host Table......................................................................................................................................49
4.2.4 NTP Configuration...............................................................................................................................................50
4.2.5 Remote Management..........................................................................................................................................51
4.3 Switching.....................................................................................................................................................53
4.3.1 Port Management................................................................................................................................................54
4.3.1.1 Port Configuration......................................................................................................................................54
4.3.1.2 SFP Module Information............................................................................................................................55
4.3.2 OAM TS-1000......................................................................................................................................................56
4.3.2.1 Local OAM TS-1000 Configuration............................................................................................................56
4.3.2.2 Remote OAM TS-1000 Configuration........................................................................................................57
4.3.2.3 OAM TS-1000 Loop Back..........................................................................................................................58
4.3.3 OAM 802.3ah ......................................................................................................................................................60
4.3.3.1 Common OAM 802.3ah Configuration.......................................................................................................60
4.3.3.2 Remote OAM 802.3ah Configuration.........................................................................................................61
4.3.3.3 OAM 802.3ah Loop Back ..........................................................................................................................62
4.3.4 VLAN Configuration.............................................................................................................................................64
4.3.4.1 VLAN Overview.........................................................................................................................................64
4.3.4.2 IEEE 802.1Q VLAN...................................................................................................................................65
4.3.4.3 VLAN Mode...............................................................................................................................................68
4.3.4.4 VLAN Tag-based Entry Config...................................................................................................................69
4.3.4.5 VLAN Port Config......................................................................................................................................71
4.3.4.6 Q-in-Q Port Config.....................................................................................................................................74
4.3.4.7 Q-in-Q Index Config...................................................................................................................................76
4.3.5 LLDP....................................................................................................................................................................78
4.3.5.1 LLDP Global Setting..................................................................................................................................78
4.3.5.2 LLDP Port Setting......................................................................................................................................79
4.3.5.3 LLDP Remote MIB.....................................................................................................................................81

User’s Manual of GT-915A
5
4.3.6 Link Fault Passthrough........................................................................................................................................82
4.4 QoS ..............................................................................................................................................................83
4.4.1 Understanding QoS.............................................................................................................................................83
4.4.2 General................................................................................................................................................................84
4.4.2.1 QoS Mode Set...........................................................................................................................................84
4.4.2.2 Class of Service.........................................................................................................................................85
4.4.2.3 802.1p-based QoS....................................................................................................................................86
4.4.2.4 DSCP-based Priority .................................................................................................................................87
4.4.2.5 IPAddr Base..............................................................................................................................................88
4.4.3 Bandwidth Control...............................................................................................................................................89
4.4.4 Storm Control ......................................................................................................................................................90
4.5 Security .......................................................................................................................................................92
4.5.1 Access Security...................................................................................................................................................92
4.5.1.1 Access Management.................................................................................................................................92
4.5.1.2 HTTPS.......................................................................................................................................................93
4.6 Maintenance................................................................................................................................................94
4.6.1 Configuration.......................................................................................................................................................94
4.6.1.1 Backup ......................................................................................................................................................94
4.6.1.2 Restore......................................................................................................................................................94
4.6.1.3 Save..........................................................................................................................................................94
4.6.2 Firmware Update.................................................................................................................................................95
4.6.3 Factory Default....................................................................................................................................................95
4.6.4 System Reboot....................................................................................................................................................96
5. TROUBLESHOOTING......................................................................................................... 97
Appendix A Networking Connection ....................................................................................99
A.1 Device‘s RJ-45 Pin Assignments.............................................................................................................99
A.2 RJ-45 cable pin assignment ...................................................................................................................100

User’s Manual of GT-915A
6
1. INTRODUCTION
Thank you for purchasing PLANET Managed Media Converter. In the following sections, unless specified, the term “Managed
Media Converter” mentioned in this manual refers to the GT-915A.
Open the box of the Managed Media Converter and carefully unpack it. The box should contain the following items:
XST-705A Smart Media Converter x 1 Quick Start QR code sheet x 1 SFP Dust Cap x 1
Power adapter (5V,2A) x 1
If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the
original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

User’s Manual of GT-915A
7
1.2 Product Description
Remotely Managed Gigabit Converter
PLANET GT-915A 10/100/1000BASE-T to 100/1000BASE-X Managed Media Converter is developed to meet the advanced
demand of network applications but it comes with the easy Plug and Play feature. The GT-915A provides all kinds of
10/100/1000Mbps Ethernet Media on RJ45 port and offers highly-stable Gigabit SFP fiber performance. It supports conversion
between 10/100/1000BASE-T and 100/1000BASE-X Ethernet, which includes SFP slot with single-mode or multi-mode media
as required. The Ethernet signal allows three types of segments to connect easily, efficiently and inexpensively.
Enhanced Smart Management Features
The GT-915A provides auto MDI/MDI-X on its TP port and built-in Link Fault Pass-through function (LFP). The LFP function
includes Link Loss Carry Forward (LLCF) and Link Loss Return (LLR), both of which can immediately alarm administrators
the problem of the link media and provide efficient solution to monitoring the net.
LLCF means when a device connected to the converter and the TP line loses the link, the converter’s fiber port will
disconnect the link of transmission.
LLR means when a device connected to the converter and the fiber line loses the link, the converter’s fiber port will
disconnect the link of transmission.
Therefore, the GT-915A greatly supports the administrators to manage the network efficiently.

User’s Manual of GT-915A
8
Network with Cybersecurity Helps Minimize Security Risks
The GT-915A comes with enhanced cybersecurity to fend off cyberthreats and cyberattacks. It supports SSHv2, TLSv1.2 and
SNMPv3 protocols to provide strong protection against advanced threats. Served as a key point to transmit data to customer's
critical equipment in a business network, the cybersecurity feature of the IGT-900-Series protects the management and
enhances the security of the mission-critical network without any extra deployment cost and effort.
User-friendly and Centralized Web Management Interface
For efficient management, the GT-915A is equipped with a remote Web/SNMP interface. With its built-in Web-based
management, PLANET GT-915A acts as an easy-to-use, platform-independent management and configuration facility. The
GT-915A also supports standard Simple Network Management Protocol (SNMP) and can be managed via any standard-based
management software.
OAM Management
TS-1000/802.3ah OAMprotocol (operation, administration, and maintenance) supported enables remote OAM compliant device
to be managed and monitored by the GT-915A.
Remotely Manage Solution
PLANET's Universal Network Management System (UNI-NMS) and CloudViewer App support IT staff to remotely manage all
network devices and monitor the GT-915A operation statuses. Thus, they're designed for both the enterprises and industries
where deployments of the GT-915A can be as remote as possible, without having to go to the actual location once a bug or
faulty condition is found. With the UNI-NMS or CloudViewer app, all kinds of businesses can now be speedily and efficiently
managed from one platform.

User’s Manual of GT-915A
9
Enhanced Traffic Control
The GT-915A can be programmed for advanced management functions such as IP address configuration, DHCP client function,
port configuration, converter configuration, 802.1Q tag VLAN, Q-in-Q VLAN, ingress/egress bandwidth control, QoS and Layer
protocol filter, and broadcast storm and bandwidth control to enhance bandwidth utilization.
Intelligent SFP Diagnosis Mechanism
The GT-915A supports SFP-DDM (digital diagnostic monitor) function that greatly helps network administrator to easily monitor
real-time parameters of the SFP transceivers, such as optical output power, optical input power, temperature, laser bias current,
and transceiver supply voltage.
Easy Chassis Installation
The GT-915A Media Converter can be used as a stand-alone unit or as a slide-in module to the PLANET Media Converter
Chassis (MC-700, MC-1500 and MC-1500R series). The media chassis can assist in providing DC power to the GT-915A
Media Converter to maintain the fiber-optic network at one centralized location. It can be DIN-rail or wall mounted for efficient
use of cabinet space.

User’s Manual of GT-915A
10
1.3 How to Use This Manual
This User’s Manual is structured as follows:
Section 2, INSTALLATION
The section explains the functions of the Managed Media Converter and how to physically install the Managed Media
Converter.
Section 3, SWITCH MANAGEMENT
The section contains the information about the software function of the Managed Media Converter.
Section 4, WEB CONFIGURATION
The section explains how to manage the Managed Media Converter by Web interface.
Section 5,TROUBLESHOOTING
The chapter explains how to do troubleshooting of the Managed Media Converter.
Appendix A
GLOSSARY

User’s Manual of GT-915A
11
1.4 Product Features
Physical Port
One 1G/100/10BASE-T RJ45 interface with auto MDI/MDI-X function
One 1G/100BASE-X SFP interface
Layer 2 Features
Supports VLAN
−IEEE 802.1Q tagged VLAN
−Supports provider bridging (VLAN Q-in-Q, IEEE 802.1ad)
−VLAN transparent
Storm Control support
−Broadcast/Multicast/DLF (Destination Lookup Failure)/ARP/ICMP
Store-and-Forward mechanism
Non-blocking full wire-speed forwarding rate
16K jumbo frame size support
Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
Automatic address learning and address aging
Supports port status/Ethernet statistics on both TP and fiber interfaces
Supports Link Fault Passthrough (LFP) and Link Layer Discovery Protocol (LLDP)
OAM Compliant
TS-1000 OAM / IEEE 802.3ah OAM / Loop Back Test
Quality of Service
Ingress Shaper and Egress Rate Limit per port bandwidth control
8 priority queues on all converter ports
Strict priority and Weighted Round Robin (WRR) CoS policies
Traffic classification
- IEEE 802.1p CoS
- IP DSCP
- IPAddress
Management
IPv4 and IPv6 dual stack management
Management Interfaces
−Web HTTP management
−Telnet Command Line Interface
−SNMP v1, v2c monitoring
−SSHv2, TLSv1.2 and SNMP v3 secure access
System Maintenance
−Firmware upload/download via HTTP
−Reset button for system reboot or reset to factory default

User’s Manual of GT-915A
12
Network Time Protocol (NTP)
SNMP Management
−SNMP trap for interface link up and link down notification
−Four RMON groups (history, statistics, alarms and events)
Network Diagnostic
−SFP-DDM (Digital Diagnostic Monitor)
Syslog remote alarm
Local system Log
PLANET Smart Discovery Utility for deploy management
PLANET Remote Management
−PLANET NMS Controller and CloudViewer for deployment management
Case and Installation
External 5V DC, 2A power supply
0 to 50 degrees C operating temperature
Supports 6000 VDC Ethernet ESD protection
Wall mounting and DIN-rail installation supported
Works with PLANET’s 10”/19” Media Converter Chassis
(MC-700/MC-1500/MC-1500R/MC-1500R48)
Plug and Play installation

User’s Manual of GT-915A
13
1.5 Product Specifications
Model GT-915A
Hardware Specifications
Copper Interface
1 x 10/100/1000BASE-T RJ45 port (Auto-MDI/MDI-X) twisted pair
Fiber Interface
1 x 100/1000BASE-X SFP Slot
Reset Button < 10 sec.: System reboot
> 10 sec.: Factory default
ESD Protection
6KV DC
Enclosure
Compact-sized metal case
Installation
Wall mountable
Media convert Chassis installation
Optional DIN-rail kit
Dimensions (W x D x H)
94 x 70 x 26mm
Weight
201g (device only)
Power Input DC 5V, 2A
Power Consumption
3.4 watts/11.6 BTU (maximum)
LED Indicator
PWR, (Green)
TP LINK/ACT, 1000 (Green)
Fiber LINK/ACT (Green)
Network Cables
10/100/1000BASE-T
：
10BASE-T: 2-pair UTP Cat. 3,4,5, up to 100 m
100BASE-TX: 2-pair UTP Cat. 5, up to 100 m
1000BASE-T: 4-pair STP Cat 5 up to 100m
100/1000GBASE-SX/LX
：
50/125μm or 62.5/125μm multi-mode fiber cable, up to 220/550m.
9/125μm single-
mode cable, extending long distance to 10/20/40/60/80/120km (vary on
fiber transceiver or SFP module)
Switching Specifications
Switch Processing
Scheme
Store and Forward
Fabric 4Gbps
Throughput
(packet per second)
2.98Mpps@64bytes
Address Table 1K entries, automatic source address learning and aging
Flow Control
Back pressure for half duplex
IEEE 802.3x pause frame for full duplex
Jumbo Frame 16K
Shared Buffer 512Kb
Layer 2 Function
Port Configuration Port disable/enable Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
Flow control disable/enable
Port Status Display each port’s speed duplex mode, link status, flow control status,
auto negotiation status

User’s Manual of GT-915A
14
VLAN
IEEE 802.1Q tag-based VLAN
IEEE 802.1ad Q-in-Q tunneling
Up to 16 VLAN groups, out of 4094 VLAN IDs
Management VLAN
Bandwidth Control Per port bandwidth control Ingress: 1~1000,000Kbps
Egress: 1~1000,000Kbps
QoS
Traffic classification based, strict priority and WRR
8-level priority for switching
Traffic classification:
- 802.1p priority
- IP DSCP
- IP Address
Security Function
Access Security
Remote management protocols control by SSH, Telnet, HTTP ans HTTPs
System Management
Basic Management
Interfaces
Telnet; Web browser; SNMP v1, v2c
Secure Management
Interfaces
SSHv2, TLS v1.2, SNMP v3
System Management
Firmware upgrade by HTTP protocol through Ethernet network
Configuration upload/download through HTTP
LLDP protocol
NTP
PLANET Smart Discovery Utility
PLANET CloudViewer app
Event Management
Remote syslog
Local system log
SNMP trap
Standards Conformance
Regulatory Compliance FCC Class A, CE Class A
Standards Compliance
IEEE 802.3, 10BASE-T
IEEE 802.3u, 100BASE-TX/FX
IEEE 802.3ab, 1000BASE-T
IEEE 802.3z, 1000BASE-SX/LX
IEEE 802.3x full-duplex flow control
IEEE 802.1p Class of Service
IEEE 802.1Q VLAN tagging
IEEE 802.1ad Q-in-Q VLAN stacking
IEEE 802.1ab LLDP
IEEE 802.3ah OAM
RFC 768 UDP
RFC 783 TFTP
RFC 791 IP

User’s Manual of GT-915A
15
RFC 792 ICMP
RFC 2068 HTTP
Environment
Operating Temperature: 0 ~ 50 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)
Storage Temperature: -10 ~ 70 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)

User’s Manual of GT-915A
16
2. INSTALLATION
This section describes the hardware features and installation of the Managed Media Converter on the desktop or rack mount.
For easier management and control of the Managed Media Converter, familiarize yourself with its display indicators, and ports.
Front panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the Managed
Media Converter, please read this chapter completely.
2.1 Hardware Description
2.1.1 Converter Front Panel
The front panel provides a simple interface monitoring the Managed Media Converter. Figure 2-1 shows the front panels of the
Managed Media Converter.
Figure 2-1: Front Panels of Managed Media Converter
■Gigabit TP interface
10/100/1000BASE-T Copper, RJ45 Twisted-pair: Up to 100 meters.
■SFP slots
100/1000BASE-X mini-GBIC slot, SFP (Small Factor Pluggable) transceiver module: From 550 meters to 2km (Multi-mode
fiber), up to above 10/20/30/40/50/60/70/120 kilometers (Single-mode fiber).
■Reset button
At the left of the front panel, the reset button is designed for rebooting the Managed Media Converter without turning off and
on the power. The following is the summary table of Reset button functions:
Reset Button Pressed and Released
Function
< 5 sec: System Reboot Reboot the Managed Media Converter.

User’s Manual of GT-915A
17
> 5 sec: Factory Default
Reset the Managed Media Converter to Factory Default
configuration. The Managed Media Converter
will then reboot
and load the default settings as below:
。Default Username: admin
。Default Password: admin
。Default IP address: 192.168.0.100
。Subnet mask: 255.255.255.0
。
Default Gateway: 192.168.0.254
2.1.2 Converter LED Indicators
Figure 2-2 shows the LED indications of the Managed Media Converter.
■System
LED Color Function
PWR Green Lights to indicate that the Media Converter has power.
■1000BASE-X Fiber Optic interface (SFP, SC & WDM)
LED Color Function
LNK/ACT Green
Lights to indicate that the fiber optic link is established.
Blinks to indicate that the fiber optic link is actively sending or receiving
data over that fiber port.
■10/100/1000BASE-T Port
LED Color Function
LNK/ACT Green Lights to indicate the link through TP port is successfully established.
Blinks to the TP port is actively sending or receiving data
1000
Speed Green
Lights to indicate that the port is operating at 1000Mbps.
Off to indicate that the port is link down or 10Mbps or 100Mbps.

User’s Manual of GT-915A
18
2.1.3 Rear Panel
The rear panel of the Managed Media Convertere consists of one DC jack, which accepts input power with 5V DC, 2A.
2.1.4 Power Information
The central pole of the Managed Media Convertere’s power jacks measures 2.5mm wide that require +5VDC power input. It
conforms to the bundled AC-DC adapter and PLANET’s media chassis. Should you have the issue of power connection, please
contact your local sales representative.
Please keep the AC-DC adapter as a spare part when the GT-915A is installed in a media chassis.
2.5mm
Width of DC Receptacle: 2.5mm
+5V for each slot
DC receptacle is 2.5mm wide that matches the central pole; the width of the Media
Converter DC jack also measures 2.5mm.
Warning: Do not install any improper unit.
The device is a power-required device, meaning it will not work till it is powered. If your networks should be active all the time,
please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data loss or network
downtime.
In some areas, installing a surge suppression device may also help to protect your Media Converter from being damaged by
unregulated surge or current to the converter or the power adapter.

User’s Manual of GT-915A
19
2.2 Media Converter Installation
This section describes the functionalities of the Media Converter’s components and guides you to how to install it on the desktop.
Basic knowledge of networking is assumed. Please read this chapter completely before continuing.
2.2.1 Stand-alone Installation
Step 1: Unpack the Media Converter.
Step 2: Connect the 5V DC power adapter to the GT-915A and verify that the Power LED lights up.
(Please refer to the 2.1.4 Power Information section for power input.)
Step 3:
3-1: Prepare a twisted-pair, straight-through Category 5e/6/7 UTP cable for Ethernet connection.
3-2: Prepare a fiber cable for connection to the SFP slot, and make sure both sides of the SFP transceiver are with the same
media type.
(Please refer to the 3.5 Cable Connection section for the type of connection.)
Step 4:
4-1: Insert one side of Category 5e/6/7 cable into the Media Converter Ethernet port (RJ45) while the other side of Category
5e/6/7 cable into the network devices' Ethernet port (RJ45), e.g., switch, PC or server.
The UTP port (RJ45) LED on the Media Converter will light up when the cable is connected with the network device.
(Please refer to the 2.1.2 LED Indicators section for the functions of LED lights.)
4-2: Connect the fiber cable.Attach the duplex LC connector on the network cable to the SFP transceiver. Attach the fiber
cable from the GT-915A to the fiber network. TX, RX must be paired at both ends.
Step 5: When all the connections are all set and the LED lights all show normally, the installation is complete.
2.2.2 Wall-mount Installation
Step 1: Please find the wall that can mount the Managed Media Converter
Step 2: Screw two screws on the wall.

User’s Manual of GT-915A
20
Step 3: Hang the Managed Media Converter on the screws from the wall.
Step 4: Refer to Chapter 2.1.4 Power Information on power supply to the Managed Media Converter.
Before mounting the
device to the wall, please check the location of the electrical outlet and the length of the
Ethernet cable.
2.2.3 Media Chassis Installation
To install the Media Converter in a 10-inch or 19-inch standard rack, follow the instructions described below.
Step 1: Place your Managed Media Converter on a hard flat surface, with the front panel positioned towards your front side.
Step 2: Carefully slide in the module until it is fully and firmly fitted into the slot of the chassis; the Power LED of the Media
Converter will turn ON.
Figure 2-2: Insert Managed Media Converter into an available slot