Planet IGT-900 Series User manual

Industrial 1-/2-Port 10/100/1000T +
1-/2-Port 100/1000/2500X SFP
Managed Media Converter
IGT-900-Series
Quick Installation Guide

Table of Contents
1. Package Contents...................................................................... 3
2. Requirements............................................................................ 4
3. Wiring the Power Inputs ............................................................ 5
3.1 Grounding the Device.......................................................... 6
4. Starting Web Management ......................................................... 7
4.1 Logging in to the Media Converter ....................................... 7
 4.2 SavingCongurationviaWeb .............................................10
5. RecoveringBacktoDefaultConguration ...................................11
6. Customer Support ....................................................................12

3
1. Package Contents
Thank you for purchasing PLANET Industrial Managed Media Converter,
IGT-900-Series. The models are as follows:
Model Port RJ45 Ports SFP Ports
IGT-900-1T1S 1 1
IGT-900-2T2S 2 2
“Media Converter” mentioned in this Quick Installation Guide refers
to the above two models.
Open the box of the Media Converter and carefully unpack it. The
box should contain the following items for each of the two models:
Package Contents Model IGT-900-1T1S IGT-900-2T2S
Quick Installation Guide  
DIN-rail Kit  
Wall Mounting Kit  
RJ45 Dust Cap 1 2
SFP Dust Cap 1 2
If any of these are missing or damaged, please contact your dealer
immediately. If possible, retain the carton including the original packing
materials to enable you to repack the product in case there is a need
to return it to us for repair.

4
2. Requirements
The Media Converter provides remote login interface for management
purposes. The following equipment is necessary for further
management:
zWorkstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS
X or later, Linux, UNIX, or other platforms are compatible with TCP/
IP Protocols.
zWorkstations are installed with Ethernet NIC (Network Interface
Card)
zEthernet Port Connection
Network cables -- Use standard network (UTP) cables with RJ45
connectors.
The above PC is installed with Web browser.
Note
It is recommended to use Internet Explorer 11.0 or
above to access the Industrial Managed Media Converter.

5
3. Wiring the Power Inputs
The Upper Panel of the Media Converter comes with one 6-contact
terminal block. Please follow the steps below to insert the power wire.
1. Insert positive/negative DC power wires into Contacts 1 and 2 for
Power 1, or Contacts 5 and 6 for Power 2.
IGT-900-1T1S and IGT-900-2T2S: DC 9-48V, AC 24V
Max. Fault Alarm Loading: 24V, 1A
DC Input: 9-48V
, 1A max.
AC Input: 24V
, 0.6A max.
V1+ V2+
PWR1 PWR2Alarm
1 2 3 4 5 6
Figure 3-1: IGT-900-1T1S/IGT-900-2T2S Upper Panel
2. Tighten the wire-clamp screws for preventing the wires from loos-
ening.
123456
V+ V- V+ V-
Power 1 Power 2
Positive (+) Pin Negative (-) Pin
IGT-900-Series Pin 1/5 Pin 2/6
Caution
PWR1 and PWR2 must provide the same DC voltage
while operating with dual power input.

6
Note
1.The wire gauge for the terminal block should be in the
range from 12 to 24 AWG.
2.Please check the wire AWG Ampere specification before
connecting Media Converter.
3.1 Grounding the Device
Users MUST complete grounding wired with the device; otherwise, a
sudden lightning could cause fatal damage to the device.
Max. Fault Alarm Loading: 24V, 1A
DC Input: 9-48V
, 1A max.
AC Input: 24V
, 0.6A max.
V1+ V2+
PWR1 PWR2Alarm
1 2 3 4 5 6
Earth Ground

7
4. Starting Web Management
The following shows how to start up the Web Management of the
Media Converter. Note the Media Converter is congured through an
Ethernet connection. Please make sure the manager PC must be set to
the same IP subnet address.
For example, the default IP address of the Media Converter is
192.168.0.100, then the manager PC should be set to 192.168.0.x
(where x is a number between 1 and 254, except 100), and the
default subnet mask is 255.255.255.0.
IP Address:
192.168.0.x IP Address:
192.168.0.100
IGT-900 Series
RJ45/UTP Cable
Figure 4-1: IP Management Diagram
4.1 Logging in to the Media Converter
1. Use Internet Explorer 8.0 or above for Web browser and enter IP
address https://192.168.0.100 (the factory-default IP address) to
access the Web interface.
2. When the following dialog box appears, please enter the default user
name “admin” and password “admin” (or the password you have
changed before) as shown in Figure 4-2.
Default IP Address: 192.168.0.100
Default User Name: admin
Default Password: admin

8
Figure 4-2:Login Screen
3. After entering the password, the main screen appears as shown in
Figure 4-3.
Figure 4-3: Web Main Screen of Industrial Managed Media Converter
The Industrial Managed Media Converter Menu on the top and left of
the Web page lets you access all the functions and status the Industrial
Managed Media Converter provides. The Menu always contains one or

9
more buttons, such as “System”, “Switching”, “QoS”, “Security”,
“Ring” and “Maintenance”.
Figure 4-4: Menu
Now, you can use the Web management interface to continue the
Media Converter management. Please refer to the user manual for
more.
Note
If you are not familiar with Switching functions or the
related parameter, press the “Help icon” anytime on
the Web page to get the help description.

10
4.2 SavingCongurationviaWeb
To save all applied changes and set the current conguration as a
startup conguration, the startup-conguration le will be loaded
automatically across a system reboot.
1. Click the Save icon on the top Menu bar.
Figure 4-5: Save Cong -- Hot Key
2. Press the “Save Conguration” button.
3. Or the other way to save the setting is to Click Maintenance, Save
Startup Cong.
Figure 4-6: Save Cong -- Maintenance