Planet WNRT-625G User manual

802.11n 3G Broadband Router
WNRT-625G
Quick Installation Guide

Table of Contents
Package Content............................................................................. 3
Hardware Installation ...................................................................... 4
Other outlook interface.................................................................... 6
Web Conguration .......................................................................... 8
Further Conguration................................................................12

3
Package Content
1 x WNRT-625G
1 x Stand
1 x Ethernet Cable
1 x Power Adapter
1 x CD ROM
1 x Quick Installation Guide
Note
If any of the above items are missing or damaged,
contact your local dealer for support.
l
l
l
l
l
l

4
Hardware Installation
1. Locate an optimum location for the WNRT-625G.
2. Adjust the antennas of WNRT-625G for the best coverage of your
wireless network.
3. There are two way connecting to Internet, One is via 3G USB port,
and another is from WAN port.
3-1. Connect your 3G/3.5G USB modem to the USB port located in
front panel of WNRT-625G.
Note
Please also check with your local dealer or PLANET Web
site for supported 3G/3.5G USB adapter.
3-2. Connect ADSL/Cable Modem to WAN port of WNRT-625G via RJ-
45 Ethernet cable

5
4. Connect all your computers, network devices (network-enabled
consumer devices, like game console, or switch / hub) to LAN port of
WNRT-625G.
5. Connect the power adapter to the wall socket, and then connect it to
the ‘12V DC’ socket of WNRT-625G.
6. Please check all LEDs on the front panel. ‘PWR’ LED should be
steadily on.

6
Other outlook interface
Radio ON/OFF
Enable/disable wireless signal button.
** In case switching wireless signal via “Radio ON/
OFF” button to “OFF” status, the functions of
wireless settings on web UI will be unavailable.

7
RST / WPS
Button
This button has two functions:
1. To Clear All Data and restore the factory
default values:
Press the RST (reset) button for longer than 20
seconds until the LED of power ash, and then the
router will reset itself to the factory default settings.
(Warning: your original congurations will be
replaced with the factory default settings)
2. To make Wi-Fi Protected Setup (WPS) simple
and easier:
Press the WPS button (for less than 3 seconds);
machine will start WPS function to build connection
between wireless network clients and this wireless
router.

8
Web Conguration
WNRT-625G provides a user friendly interface for users to congure
it via web browser. Please follow the steps below to congure WNRT-
625G basic settings.
1. Open your web browser and type WNRT-625G default IP address
(http://192.168.0.1) into the “Address Field” of you web browser.
Before conguration, please make sure your PC’s IP address is under
the same IP range with WNRT-625G.
2. After enter the IP address and press Enter key, you can see the
dialog box appear as below, please enter the User name and Pass-
word with “admin”. Then press “OK”.

9
3. Please click “Quick Setup” on the left panel to setup WNRT-625G.
4. Select a Time Zone that corresponds to your country. Click “Next” to
continue.

10
5. WNRT-625G supports 7 Internet connection types. Please click
“3G/3.5G” to congure 3G mobile Internet. (Other methods please
refer to the manual in CD-ROM.
6. Please input the Internet connection parameters if it is required by
your 3G/3.5G Service Provider. Click “Next” to continue.

11
7. Congure wireless relative value (included choosing or changing Band
/ Band / Channel Number)
8. Select encryption type to secure your wireless network.
9. Click “Apply” to save the settings.
10. Please wait for 30 seconds for WNRT-625G restart. Then click “OK”.

12
Further Conguration
If you want to congure WNRT-625G with more detail settings, please
refer to the manual in the CD-ROM. If you have any difculty on
resolving the problem while installing or using WNRT-625G, please
contact with local dealer or PLANET technical support.