Planet IPX-1900 User manual

Internet Telephony PBX system
IPX-1900
Quick Installation Guide

Table of Content
Document Objectives ....................................................................................... 3
Equipment Packaging & Overview .................................................................... 3
Installation Connect the IP PBX......................................................................... 4
Physical Introduction................................................................................... 4
Physical Installation .................................................................................... 5
Basic Conguration .................................................................................... 6
A. Web conguration access ................................................................. 6
B. IP PBX Quick Conguration .............................................................. 6
Step 1. Internet Setting ....................................................................... 7
Step 2. NAT setup ............................................................................... 8
Step 3. IP PBX Setup........................................................................... 9
Quick reference in CD-ROM guide ...............................................................10

3
Document Objectives
This guide provides physical installation, network congurations, and Internet
access establishment information for the PLANET Internet Telephony PBX System.
Equipment Packaging & Overview
Package Contents
IP PBX Unit
Power adapter (12V)
Quick Installation Guide
User’s Manual CD
RJ-45 cable
RS-232 cable
Rack mount

4
Installation Connect the IP PBX
Physical Introduction
Figure1. Font Panel of IP-1900
Front Panel LED State Descriptions
PWR On
Off
PBX Power ON
PBX Power OFF
SYS On
Flashing
System is booting
System is ready
LAN
On
Flashing
Off
LAN is connected successfully
Data is transmitting
Ethernet not connected to PC
WAN
On
Flashing
Off
PBX network connection established
Data trafc on cable network
Waiting for network connection
FXO/FXS Port
On
Flashing
Off
Port is busy
Ring indication. (FXS only)
Port is not enabled.
Table 1. Font Panel description of IP PBX
Figure 2. Rear Panel of IPX-1900

5
12V DC 12V DC Power input outlet
Power Switch “|” power is on, “O” Power is off
Reset
(Rest Button)
Push this button until 3 -5 seconds, and IP PBX will be
set to factory default conguration.
RS – 232 Port 9 pin RS232 Serial port, Data rates 57600 bits.
LAN
(Local Area network)
Connect to PC with Ethernet cable. 1 port allows your
PC or Switch/Hub to be connected to the IPBX through
a networking cable with RJ-45 connectors used on
10Base-T and 100Base-TX networks.
WAN
(Wide Area network)
Connect to the network with an Ethernet cable. This
port allows your IPBX to be connected to an Internet
Access device, e.g. router, cable modem, ADSL modem,
through a networking cable with RJ-45 connectors used
on 10Base-T and 100Base-TX networks.
Slot A/B 2 external slots with compliance FXO/FXS/FSL module.
FXS Port
(Modular IPX-19FS)
Connect to Phone with RJ-11 (Black) analog line. FXS
port was connected to your telephone sets, FAX, or
Trunk Line of PBX.
FXO Port
(Modular IPX-19FO)
Connect to PBX or CO line with RJ-11 (Write) analog
line. FXO port was connected to the extension port of a
PBX or directly connected to a PSTN line of carrier
Note: IPX-19SL 2-Port PBX Life Line Module IPX-1900 (1FXO, 1FXS)
Table 2. Rear Panel description of IP PBX
Internet
Internet IPX-1900 IP Phone
Physical Installation
Step 1: Connecting Power AC Power (12V DC).
Note
Use only the power adapter shipped with the unit to ensure correct
functionality.

6
Step 2: Connecting LAN to a PC
1. Connect the Ethernet cable (with RJ-45 connector) to LAN port.
2. Connect the other end of the Ethernet cable to your PC’s installed network inter-
face card (NIC).
Step 3: Connecting WAN to Internet
1. Connect the Ethernet cable (with RJ-45 connector) to WAN port.
2. Connect the other end of the Ethernet cable to DSL/Cable modem or the
external Ethernet hub or switch.
Basic Conguration
A. Web conguration access
The IP PBX provides GUI (Web based, Graphical User Interface) for machine
management and administration.
The default IP address of IP PBX LAN side is 192.168.0.1. You may now open
your web browser, and insert http://192.168.0.1 in the address bar of your web
browser to logon Internet IP PBX web conguration page.
The IP PBX will prompt for logon username/password, please enter: admin / 123
to continue device’s administration.
Note
In order to connect the IP PBX for administration, please locate
your PC in the same network segment (192.168.0.x) of IP PBX. If
you’re not familiar with TCP/IP, please refer to related chapter on
user’s manual CD or consult your network administrator for proper
network configurations.
B. IP PBX Quick Conguration
After pass the authentication, please click for quick IP PBX
setup.
For most users, Internet access is the primary application. The IP PBX supports the
WAN interface for Internet access and remote access. The following sections will
explain more details of WAN Port Internet access and broadband access setup.

7
Step 1. Internet Setting
Three modes are available for WAN setup
I. Fixed – IP User: If you are a leased line user with a xed IP address, ll out
the following items with the information provided by your ISP.
Figure 3. Wizard-NAT Static Setting Screen
II.DHCP – Cable Modem User: Get WAN IP Address automatically
Figure 4. Wizard-DHCP Setting Screen

8
III. ADSL Dial-Up User (PPPoE Enable): Some ISP’s provide DSL-based service and
use PPPoE to establish communication link with end-users. If you are connected
to the Internet through a DSL line, check with your ISP to see if they use
PPPoE. If they do, you need to select this item.
Figure 5. Wizard-PPPoE Setting Screen
Step 2. NAT setup
NAT (Network Address Translation) is a method of connecting multiple computers
to the Internet using one IP address.
Figure 6. Wizard-LAN IP Setting Screen

9
LAN IP Address: Private IP address for connecting to a local private network
Subnet Mask: Subnet mask for the local private network (Default:
255.255.255.0).
DHCP Server: Enable to open LAN port DHCP server.
Assigned DHCP IP Address: DHCP server range from start IP to end IP.
DHCP IP Lease Time: Client to ask DHCP server refresh time, range from 60 to
86400 seconds
Step 3. IP PBX Setup
The IP PBX allows multiple ITSP providers / User Extensions registration by simply
ll-in the required information in the provided table.
Figure 7. Wizard-IP PBX Setting Screen
Service Provider:
Caller id: Input service provider caller id / name
Username: Input Provider name
Password: Input Provider password
Host: Input Providers server address.
Port: Input Providers Port
User Extensions：
User Extension: Input Extension number
Password: Input Extension password
Caller id: Input Extension caller id

10
Quick reference in CD-ROM guide
This guide is used to help you startup your IP PBX settings. It is also recommended
to check the user manual CD-ROM for more details like the “IP PBX Setup”, “Trunk
Management”, and how to set the device back to default value.

This page is intentionally left blank

This page is intentionally left blank