Planet GSW-1601 User manual

16/24-Port 10/100/1000Mbps
Gigabit Ethernet Switch
GSW-1601/GSW-2401
User's Manual

Trademarks
Copyright © PLANET Technology Corp. 2008.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks
belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all
environments and applications, and makes no warranty and representation, either
implied or expressed, with respect to the quality, performance, merchantability, or
tness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User’s Manual is subject to change without notice and does not
represent a commitment on the part of PLANET. PLANET assumes no responsibility
for any inaccuracies that may be contained in this User’s Manual. PLANET makes
no commitment to update or keep current the information in this User’s Manual,
and reserves the right to make improvements to this User’s Manual and/or to the
products described in this User’s Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or incomplete,
we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.

CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human health as a
result of the presence of hazardous substances in electrical and electronic
equipment, end users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do not
dispose of WEEE as unsorted municipal waste and have to collect such
WEEE separately.
Revision
PLANET 16/24-Port 10/100/1000Mbps Gigabit Ethernet Switch User's Manual
For Models: GSW-1601 / GSW-2401
Revision: 3.0 (April. 2008)
Part No: EM_GSW1624v3 (2011-A50140-000)

TABLE OF CONTENTS
1. INTRODUCTION.......................................................................................... 5
1.1 Package Contents ................................................................................ 5
1.2 How to Use This Manual ..................................................................... 5
1.3 Product Features ................................................................................. 5
1.4 Product Specications .......................................................................... 6
2. INSTALLATION............................................................................................ 7
2.1 Product Description.............................................................................. 7
2.1.1 Product Overview ....................................................................... 7
2.1.2 Switch Front Panel ..................................................................... 8
2.1.3 LED Indicators ........................................................................... 8
2.1.4 Switch Rear Panel ...................................................................... 8
2.2 Installing the Switch ............................................................................ 9
2.2.1 Desktop Installation.................................................................... 9
2.2.2 Rack Mounting ..........................................................................10
3. Switch Operation .......................................................................................12
3.1 Address Table.....................................................................................12
3.2 Learning ............................................................................................12
3.3 Forwarding & Filtering.........................................................................12
3.4 Store-and-Forward..............................................................................12
3.5 Auto-Negotiation ................................................................................13
4. Troubleshooting .........................................................................................14
APPENDIX A NETWORKING CONNECTION .........................................................15
A.1 Switch's RJ-45 Pin Assignments ............................................................15
A.2 RJ-45 cable Pin Assignments ................................................................15

5
1. INTRODUCTION
1.1 Package Contents
Check the contents of your package for following parts:
● Gigabit Ethernet Switch x 1
● User's manual x 1
● Power cord x 1
● Rubber feet x 4
● Two rack-mounting brackets with attachment screws x 1
If any of these are missing or damaged, please contact your dealer immediately,
if possible, retain the carton including the original packing material, and use them
against to repack the product in case there is a need to return it to us for repair.
1.2 How to Use This Manual
This Gigabit Ethernet Switch User Manual is structured as follows:
Chapter 2 Installation
The chapter explains the feature, functionality and the physical installation of the
Gigabit Ethernet Switch.
Chapter 3 Switch operation
The chapter explains the Gigabit Ethernet Switch transmit operation.
Chapter 4 Troubleshooting
The chapter explains the troubleshooting of the Gigabit Ethernet Switch.
Appendix A
This chapter contains cable information of the Gigabit Ethernet Switch.
In the following section, the term “Gigabit Ethernet Switch” means the GSW-
1601 / GSW-2401.
1.3 Product Features
● Comply with IEEE 802.3, 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab
1000Base-T Ethernet standard
● 16 / 24-Port 10/100/1000Mbps Gigabit Ethernet ports
● Features Store-and-Forward mode with wire-speed ltering and forwarding rates
● Hardware based 10/100Mbps, half / full duplex and 1000Mbps full duplex mode,
ow control and auto-negotiation

6
● IEEE 802.3x ow control for full duplex operation and Backpressure for half
duplex operation
● Integrated address look-up engine, support 8K absolute MAC addresses
● 9K Jumbo packet support
● Automatic address learning and address aging
● Supports Auto MDI/MDI-X function
● Support CSMA/CD protocol
● 100~240VAC, 0.6A, 50~60Hz universal Power input
● FCC, CE class A compliant
1.4 Product Specications
Product GSW-1601 GSW-2401
Hardware Specication
10/100/1000Base-T MDI/MDIX
Ports
16 24
Throughput (packet per second)
23.8Mpps 35.7Mpps
Switch fabric
32Gbps 48Gbps
Weight
2.50kg 2.71kg
Power Consumption / Dissipation
21 watts / 71 BTU 34 watts / 116 BTU
Power Requirement
100~240 VAC, 0.6A, 50-60 Hz
Dimensions (W x D x H)
440 x 180 x 45mm, 1U height
Switch Processing Scheme
Store-and-Forward
Address Table
8K entries
Jumbo packet size
9K
Flow Control
Back pressure for half duplex, IEEE 802.3x Pause
Frame for full duplex
Temperature
Operating: 0~50 degree C
Storage -40~70 degree
Humidity Operating:
5% to 90%, Storage: 5% to 90% (Non-condensing)
Standards Conformance
Regulation Compliance
FCC Part 15 Class A, CE
Standards Compliance
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab(Gigabit Ethernet)
IEEE 802.3x (Full-duplex ow control)

7
2. INSTALLATION
This section describes the functionalities of the Gigabit Ethernet Switch’s
components and guides how to install it on the desktop. Basic knowledge of
networking is assumed. Please read this chapter completely before continuing.
2.1 Product Description
The PLANET Gigabit Ethernet Switch is 10/100/1000Mbps Gigabit Ethernet Switch
with 16/24 ports respectively, and non-blocking wire-speed performance. With
a 32/48Gbps internal switching fabric, the Gigabit Ethernet Switch can handle
extremely large amounts of data in a secure topology linking to a backbone or
high capacity servers.
The Gigabit Ethernet Switch has 8K MAC Address table. The Gigabit Ethernet
Switch offers wire-speed packets transfer performance without risk of packet loss.
The high data throughput of Gigabit Ethernet Switch makes it ideal for most Gigabit
environments, especially while network upgrades to a Gigabit environment.
All RJ-45 copper interfaces support 10/100/1000Mbps Auto-Negotiation for optimal
speed detection through RJ-45 Category 6, 5 or 5e cables. Support standard for
Auto-MDI/MDI-X that can detect the type of connection to any Ethernet device
without requiring special straight or crossover cables.
The Flow Control function allows your Gigabit Ethernet Switch supported routers
and Servers to directly connect to this Switch for fast, reliable data transfer.
2.1.1 Product Overview
The PLANET Gigabit Ethernet Switch with 16/24 RJ-45 10/100/1000Mbps ports for
high-speed network connectivity. The Gigabit Ethernet Switch can also automatically
identify and determine the correct transmission speed and half/full duplex mode
of the attached devices with its 16/24 ports. The Gigabit port with jumbo frame
feature supported, can handle extremely large amounts of data transmission in a
secure topology linking to a backbone or high-power servers.
The Gigabit Ethernet Switch also supports Store-and-Forward forwarding scheme
to ensure low latency and high data integrity, eliminates unnecessary trafc and
relieves congestion on critical network paths. With an intelligent address recognition
algorithm, the Gigabit Ethernet Switch could recognize up to 8K different MAC
address and enables ltering and forwarding at full wire speed.

8
2.1.2 Switch Front Panel
Figure 2-1 & 2-2 shows a front panel of Gigabit Ethernet Switch.
Figure 2-1 GSW-1601 front panel
Figure 2-2 GSW-2401 front panel
2.1.3 LED Indicators
GSW-1601 / GSW-2401
System
LED Color Function
PWR Green Lights to indicate that the Switch has power.
FAN Green Lights to indicate that FAN is operating.
Per 10/100/1000Mbps port
LED Color Function
LNK / ACT Green
Lights to indicate the link through that port is
established successfully.
Blinks indicate that the Switch is actively sending or
receiving data over that port.
1000 Green Lights to indicate the port is run at 1000Mbps.
Off: indicate that the port is operating at 10/100Mbps.
2.1.4 Switch Rear Panel
Figure 2-3 & 2-4 shows a rear panel of Gigabit Ethernet Switch.
Figure 2-3 GSW-1601rear panel

9
Figure 2-4 GSW-2401 rear panel
Power
Notice
1. The device is a power-required device, it means, it will not work
till it is powered. If your networks should active all the time,
please consider using UPS (Uninterrupted Power Supply) for your
device. It will prevent you from network data loss or network
downtime.
2. In some area, installing a surge suppression device may
also help to protect your Gigabit Ethernet Switch from being
damaged by unregulated surge or current to the Switch or the
power adapter.
2.2 Installing the Switch
This part describes how to install your Gigabit Ethernet Switch and make
connections to it. Please read the following topics and perform the procedures in
the order being presented.
Note
This Gigabit Ethernet Switch does not need software configuration.
2.2.1 Desktop Installation
To install the Gigabit Ethernet Switch on desktop, simply follow the next steps:
Step 1: Attach the rubber feet to the recessed areas on the bottom of the Gigabit
Ethernet Switch.
Step 2: Place the Gigabit Ethernet Switch on desktop near an AC power source.
Step 3: Keep enough ventilation space between the Gigabit Ethernet Switch and
the surrounding objects.
Note
When choosing a location, please keep in mind the environmental
restrictions discussed in Chapter 1, Section 1.4 Product Specifica-
tions.
Step 4: Connect your Gigabit Ethernet Switch to network devices.

10
A. Connect one end of a standard network cable to the 10/100/1000 RJ-45 ports on the
front of the Gigabit Ethernet Switch.
B. Connect the other end of the cable to the network devices such as printer servers, work-
stations or routers…etc.
Note
Connection to the Gigabit Ethernet Switch requires UTP Category 5
network cabling with RJ-45 tips. For more information, please see
the Cabling Specification in Appendix A.
Step 5: Supply power to the Gigabit Ethernet Switch.
A. Connect one end of the power cable to the Gigabit Ethernet Switch.
B. Connect the power plug of the power cable to a standard wall outlet.
When the Gigabit Ethernet Switch receives power, the Power LED should remain
solid Green.
2.2.2 Rack Mounting
To install the Gigabit Ethernet Switch in a 19-inch standard rack, follow the
instructions described below.
Step 1: Place your Gigabit Ethernet Switch on a hard at surface, with the front
panel positioned towards your front side.
Step 2: Attach a rack-mount bracket to each side of the Switch with supplied
screws attached to the package. Figure 2-5 shows how to attach brackets
to one side of the Gigabit Ethernet Switch.
Figure 2-5 Attaching the brackets to the Gigabit Ethernet Switch
Caution
You must use the screws supplied with the mounting brackets.
Damage caused to the parts by using incorrect screws would invali-
date your warranty.
Step 3: Secure the brackets tightly.