Planet GSW-4804SF User manual

48-Port 10/100/1000Mbps with 4-Port
Shared SFP Web Smart Switch
GSW-4804SF
Quick Installation Guide

Table of Contents
Package Content.............................................................................................. 3
Requirements ................................................................................................ 3
Start Web Management.................................................................................... 4
While IP Address be changed or forgotten admin password – ............................. 6
Customer Support .......................................................................................... 8

3
Package Content
Thank you for purchasing PLANET 48-Port 10/100/1000Mbps with 4-Port Shared
SFP Web Smart Switch, GSW-4804SF. Terms of “Switch” in following section of
this Quick installation guide means the GSW-4804SF.
Upon open the box of the Switch and carefully unpack it. The box should contain
the following items:
The Switch x 1
This Quick Installation Guide x 1
User’s manual CD x 1
RS-232 Console cable x 1
Power Cord x 1
Rubber feet x 4
Two rack-mounting brackets with attachment screws x1
If any item is found missing or damaged, please contact your local reseller for
replacement.
Requirements
The GSW-4804SF provide remote Web interface for manage; the following
equipments are necessary for further management.
Network cables: Use standard network (UTP) cables with RJ45 connectors.
Subscriber PC installed with Ethernet NIC (Network Card)
The operate system of subscriber PC that running Windows 98/ME, NT4.0, 2000/XP,
MAC OS9 or later, Linux, UNIX or other platform compatible with TCP/IP protocols.
l
l
l
l
l
l
l

4
Start Web Management
The PLANET GSW-4804SF provides a built-in browser interface. You can manage
the Switch remotely by having a remote host with Web browser, such as Microsoft
Internet Explorer, Netscape Navigator or Mozilla Firefox.
The following shows how to startup the Web Management of the Switch, please
note the Switch is congured through an Ethernet connection, make sure the
manager PC must be set on the same IP subnet address, for example, the
default IP address of the Switch is 192.168.0.100 (the factory-default IP address),
then the manager PC should be set at 192.168.0.x (where x is a number between
1 and 254, except 100), and the default subnet mask is 255.255.255.0.
Use Internet Explorer 5.0 or above Web browser, enter default IP address
http://192.168.0.100
Default IP Address: 192.168.0.100
Default Account: admin
Default Password: admin

5
To access the Web interface then the Web login screen appears in Figure 1.
Figure 1. Web Login Screen of GSW-4804SF
After entering the username and password (default user name and password is
“admin”) in login screen (Figure 1 appears). The Web main screen appears as
Figure 2.
Figure 2. Web Main Screen of GSW-4804SF
Now, you can use the Web management interface to continue the Switch
management, please refer to the user manual for more.
Note
For security reason, please change and memorize the new pass-
word after this first setup.

6
While IP Address be changed or forgotten admin
password –
To reset the IP address to the default IP Address “192.168.0.100” and the user
name / password to factory default mode (default user name and password is
admin).
Connect a serial cable to a COM port on a PC or notebook computer and to serial
(console) port of the Switch. The console port of the Switch is DCE already, so
that you can connect the console port directly through PC without the need of Null
Modem.
Figure 3. Console port connection of GSW-4804SF
A terminal program is required to make the software connection to the Switch.
Windows Hyper Terminal program may be a good choice. It can be accessed from
the Start menu. Click START, then Programs, Accessories and then Hyper Terminal.
MS-DOS based terminal program such as PC-PLUS, PROCOMM, can also make the
connection with the Switch built-in software. The COM port should be congured
as:
Baud: 9600
Parity: None
Data bits: 8
Stop bits: 1
Flow Control: None
l
l
l
l
l

7
Once the terminal has connected to the device, power on the Switch, the terminal
will display that is perform the loading GSW-4804SF program procedures. When
the “Waiting 2 seconds : Press <d> for default parameters” text appears,
please press “d” from your keyboard then the Switch will perform the reset device
to factory default mode procedure and the screen appears in Figure 4.
Figure 4. Loading Default Parameters of GSW-4804SF
Note
This Console interface only provide reset system to factory default
mode, for further switch management. Please access GSW-4804SF
Web interface for further management.

8
Customer Support
Thank you for purchase PLANET products. You can browse our online FAQ resource
at the PLANET web site rst to check if it could solve you issue. If you need more
support information, please contact PLANET switch support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2008.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks
belong to their respective owners.